1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. -rrp 05-02-09 R. MONNIN REV SHET REV SHET REV STATUS REV A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 PMIC N/A PREPARED BY LARRY T. GAUDER DEFENSE SUPPLY CENTER COLUMBUS STAND
2、ARD MICROCIRCUIT DRAWING CHECKED BY THOMAS M. HESS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY MONICA L. POELKING MICROCIRCUIT, DIGITAL, BIPOLAR, ADVANCED SCHOTTKY TTL, OCTAL BUFFERS/LINE DRIVERS WITH 3-STATE OUTPUTS AND 25 OHM SE
3、RIES PULL-DOWN RESISTORS IN OUTPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 94-08-01 AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-93250 SHEET 1 OF 12 DSCC FORM 2233 APR 97 5962-E125-05 Provided by IHSNot for ResaleNo reproduction or networking per
4、mitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (de
5、vice classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as sh
6、own in the following example: 5962 - 93250 01 M R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices
7、meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). T
8、he device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54F2244 Octal buffers/line drivers with 3-state outputs and 25 series pull-down resistors in outputs 1.2.3 Device class designator. The device class designator is a single letter identifying th
9、e product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2
10、.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat package 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The
11、 lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS C
12、OLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc Input voltage range (VIN) . -0.5 V dc to +7.0 V dc Input current range (IIN) -30 mA to 5.0 mA Standard output -0.5 V to VCCTRI-STATE output -0.
13、5 V to 5.5 V Storage temperature range . -65C to +150C Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +175C Maximum power dissipation (PD): . 500 mW 2/ Thermal resistance, junction-to-case (JC) See MIL-STD-1835 1.4 Recommended operating conditions. Supply voltage (VCC) 4.
14、5 V dc to 5.5 V dc High level input voltage (VIH) . 2.0 V Low level input voltage (VIL) 0.8 V Case operating temperature range (TC) -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this
15、drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-ST
16、D-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at h
17、ttp:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum
18、 levels may degrade performance and affect reliability. 2/ Maximum power dissipation is defined as VCCx ICCand must withstand the added PDdue to the short circuit output test (e.g., IOS). Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICRO
19、CIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. N
20、othing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modif
21、ied in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices a
22、nd as specified herein. 3.2 Design, construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline. The case outline s
23、hall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuit and swit
24、ching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as spec
25、ified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with
26、the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA
27、designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or
28、 “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the r
29、equirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an ap
30、proved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of confo
31、rmance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of produc
32、t (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable
33、required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 30 (see MIL-PRF-38535, appendix A). Provided by IH
34、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Con
35、ditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max High level output voltage VOH1VCC= 4.5 V, VIL= 0.8 V IOH= -12 mA, VIH= 2.0 V 1, 2, 3 01 2.0 V Low level output voltage VOL1VCC= 4.5 V, VIH= 2.0 V IOL= 1 mA, VIL= 0.8 V 1, 2, 3 01 0.5 V High level outpu
36、t voltage VOH2VCC= 4.5 V, IOH= -3 mA 1, 2, 3 01 2.4 V Low level output voltage VOL2VCC= 4.5 V, IOL= 12 mA 1, 2, 3 01 0.75 V ICCHVCC= 5.5 V, VIN= 5.5 V 60 ICCLVCC= 5.5 V, VIN= GND 90 Supply current ICCZVCC= 5.5 V, VIN= 5.5 V 1, 2, 3 01 90 mA Input clamp voltage VIKVCC= 4.5 V, II= -18 mA 1 01 -1.2 V I
37、IH1VCC= 5.5 V, VIN= 2.7 V 1, 2, 3 20 High level input current IIH2VCC= 5.5 V, VIN= 7.0 V 1, 2, 3 01 100 A IIL1VCC= 5.5 V VIN= 0.5 V other inputs = 5.5 V Standard Inputs (In) -1.6 Low level input current IIL2OE1 , OE2 1, 2, 3 01 -1.0 mA IOZHVCC= 5.5 V, VOUT= 2.7 V 50 Output leakage current IOZLVCC= 5
38、.5 V, VOUT= 0.5 V 1, 2, 3 01 -50 A Short circuit output current IOSVCC= 5.5 V, VOUT= 0.0 V 1/ 1, 2, 3 01 -100 -225 mA Functional test See 4.4.1b, VCC= 4.5 V and 5.5 V 7, 8 01 VCC= 5.0 V 9 01 1.5 7.0 tPLHVCC= 4.5 V to 5.5 V 10, 11 1.5 7.0 VCC = 5.0 V 9 2.5 8.0 Propagation delay time Into OntPHLRL= 50
39、0 CL= 50 pF tr= 2.5 ns tf= 2.5 ns VCC= 4.5 V to 5.5 V 10, 11 2.0 8.0 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218
40、-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max VCC= 5.0 V 9 1.5 9.0 tPZHVCC= 4.5 V to 5.5 V 10, 11 1.0 9.5 VCC = 5.0 V 9
41、2.5 11.5 Output enable time tPZLRL= 500 CL= 50 pF tr= 2.5 ns tf= 2.5 ns VCC= 4.5 V to 5.5 V 10, 11 01 2.5 12.0 ns VCC= 5.0 V 9 1.5 9.0 tPHZVCC= 4.5 V to 5.5 V 10, 11 1.0 9.5 VCC = 5.0 V 9 1.5 8.5 Output disable time tPLZRL= 500 CL= 50 pF tr= 2.5 ns tf= 2.5 ns VCC= 4.5 V to 5.5 V 10, 11 01 1.5 9.5 ns
42、 1/ Not more than one output should be shorted at a time. For testing IOS, the use of high speed test apparatus and/or sample and hold techniques are preferable in order to minimize internal heating and more accurately reflect operational values. Otherwise prolonged shorting of a high output may rai
43、se the chip temperature well above normal and thereby cause invalid readings in other parameter tests. In any sequence of parameter tests, IOStests should be performed last. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWIN
44、G SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Device type 01 Case outline R, S, and 2 Terminal number Terminal symbol 1 OE1 2 1a 3 0e 4 1b 5 0f 6 1c 7 0g 8 1d 9 0h 10 GND 11 1h 12 0d 13 1g 14 0c 15 1f 16 0b 17 1e 18 0a 19
45、OE2 20 VCCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 OE1 1an
46、0an OE2 1bn 0bn H X Z H X Z L H H L H H L L L L L L H = High voltage level L = Low voltage level X = Irrelevant Z = High impedance FIGURE 2. Truth table. FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT D
47、RAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 NOTES: 1. Pulse generator characteristics: PRR = 1 MHz, tr= tf 2.5 ns duty cycle = 50 percent. 2. CL= 50 pF 3. RL= 500 4. CL= includes probe and jig capacitance 5. VM= 1.5
48、 V FIGURE 4. Test circuit and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-93250 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance
