1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Delete subgroup 4 entirely from final electrical parameters for device classes M, Q, and V under Table II. Changes in accordance with N.O.R. 5962-R194-95. 95-08-25 M. A. FRYE B Drawing updated to reflect current requirements. Redrawn - ro 02-02-2
2、1 R. MONNIN C Add new footnote 4/ to SSBW, GFP, GFR, HD2, and HD3 tests as specified under Table I. Make changes to Table II. - ro 03-06-12 R. MONNIN D Updating boilerplate paragraphs. - ro 09-06-02 R. RODENBECK REV SHET REV SHET REV STATUS REV D D D D D D D D D D D D D OF SHEETS SHEET 1 2 3 4 5 6 7
3、 8 9 10 11 12 13 PMIC N/A PREPARED BY RICK OFFICER CHECKED BY RAJESH PITHADIA DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPROVED BY MICHAEL FRYE STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPARTMENT OF
4、DEFENSE DRAWING APPROVAL DATE 94-08-23 MICROCIRCUIT, LINEAR, DUAL, WIDEBAND, VIDEO OPERATIONAL AMPLIFIER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL D SIZE A CAGE CODE 67268 5962-94719 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E325-09 Provided by IHSNot for ResaleNo reproduction or networking permitt
5、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device
6、 classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown i
7、n the following example: 5962 - 94719 01 M P A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet
8、the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The de
9、vice type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 CLC412 Dual, wideband, video operational amplifier 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Devi
10、ce requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designat
11、ed in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style P GDIP1-T8 or CDIP2-T8 8 Dual-in-line 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix
12、 A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum rating
13、s. 1/ Supply voltage (VCC) 7 V dc Output current (IOUT) 96 mA Common mode input voltage VCCPower dissipation (PD) 1.15 W Lead temperature (soldering, 10 seconds) +300C Junction temperature (TJ) . +175C Storage temperature range -65C to +150C Thermal resistance, junction-to-case (JC): Case P . +50C/W
14、 Case 2 . +45C/W Thermal resistance, junction-to-ambient (JA): Case P . +100C/W Case 2 . +60C/W 1.4 Recommended operating conditions. Supply voltage (VCC) 5 V dc Gain range (AV) +1 V/V to +10 V/V Ambient operating temperature range (TA) . -55C to +125C 2. APPLICABLE DOCUMENTS 2.1 Government specific
15、ation, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38
16、535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Dr
17、awings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a
18、conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause
19、 permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS C
20、OLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (
21、QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, an
22、d physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Ter
23、minal connections. The terminal connections shall be as specified on figure 2. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table
24、 I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN lis
25、ted in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator
26、shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as req
27、uired in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements
28、 of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved sour
29、ce of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as r
30、equired for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2
31、herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required do
32、cumentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 49 (see MIL-PRF-38535, appendix A). Provided by IHSNot for Re
33、saleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/
34、-55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxStatic and dc tests. Input bias current +IBN1,2 01 -12 +12 A 3 -28 +28 -IBN1 -15 +15 2 -20 +20 3 -34 +34 Input offset voltage VIO1 01 -6 +6 mV 2 -12 +12 3 -10 +10 TCTA= +125C, -55C 3/ 2 01 -90 +90 nA/C Averag
35、e input bias current drift (+IBN) 3 -187 +187 TC2 -80 +80 (-IBN) 3 -125 +125 Average input offset voltage drift TC(VIO) TA= +125C, -55C 3/ 2,3 01 -60 +60 V/C Supply current ICCRL= 1,2 01 12.8 mA 3 13.6 PSRR +VS= +4.5 V to +5.0 V, 1 01 46 dB Power supply rejection ratio -VS= -4.5 V to 5.0 V 2,3 44 CM
36、RR VCM= 1 V 4 01 45 dB Common mode 3/ rejection ratio 5,6 43 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
37、ION LEVEL D SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxFrequency domain tests. Small signal bandwidth SSBW -3 dB bandwidth, 4 01 175 MHz
38、 VOUT 0.5 VPP5 4/ 135 6 4/ 150 Large signal bandwidth LSBW -3 dB bandwidth, 3/ 4,6 01 80 MHz VOUT 4.0 VPP5 65 GFP 0.1 MHz to 30 MHz, 4 01 0.1 dB Gain flatness peaking high VOUT 0.5 VPP5 4/ 0.2 6 4/ 0.1 Gain flatness rolloff GFR 0.1 MHz to 30 MHz, 4 01 0.3 dB VOUT 0.5 VPP5 4/ 0.3 6 4/ 0.4 Linear phas
39、e deviation LPD DC to 75 MHz, 3/ 4,5 01 1.0 Degrees VOUT 0.5 VPP6 1.3 Differential gain DG 4.43 MHz, RL= 150 3/ 4,6 01 0.04 % 5 0.08 Differential phase DP 4.43 MHz, RL = 150 3/ 4,6 01 0.04 Degree 5 0.08 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitt
40、ed without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise s
41、pecified Group A subgroups Device type Limits 2/ Unit Min MaxDistortion and noise tests. HD2 2 VPPat 20 MHz 4 01 -42 dBc Second harmonic distortion 5 4/ -38 6 4/ -42 HD3 2 VPPat 20 MHz 4 01 -46 dBc Third harmonic distortion 5 4/ -42 6 4/ -46 VEN 1 MHz 3/ 4,6 01 3.4 nV / Equivalent noise input positi
42、ve voltage 5 3.8 Hz ICN 1 MHz 3/ 4,6 01 13.9 pA / Equivalent input inverting current noise 5 15.5 Hz NICN 1 MHz 3/ 4,6 01 2.6 pA / Equivalent input non- inverting current noise 5 3.0 Hz Noise floor SNF 1 MHz 3/ 4,6 01 -156 dBm 5 -155 (1 Hz) Crosstalk (input referred) XTLK At 10 MHz 3/ 4,5,6 01 -64 d
43、B See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 8 DSCC FORM 2234 APR 97 TABLE I. Electric
44、al performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxTiming tests. Rise and fall time tRS0.5 V step 3/ 9 01 2.0 ns 10 2.6 11 2.3 tRL4 V step 3/ 9,11 4.4 10 4.8 Slew rate SR Measured 1 V with 3/
45、 2 V step, AV= 2 4,6 01 1000 V/s 5 800 Settling time tS2 V step at 0.05 % of 3/ the fixed value 9,11 01 18 ns 10 20 Overshoot OS 0.5 V step 3/ 9,10,11 01 15 % Performance tests RIN3/ 4,5 01 500 k Input resistance (positive) 6 300 Input capacitance (positive) CIN3/ 4,5,6 01 2.0 pFOutput resistance RO
46、UTClosed loop 3/ 4 01 0.3 5 0.2 6 0.6 Output voltage range VOUTRL= 3/ 1,2 01 -3.0 +3.7 V 3 -2.9 +3.6 RL= 100 3/ 1,2 -2.7 +2.7 3 -2.5 +2.0 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZ
47、E A 5962-94719 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL D SHEET 9 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TA+125C unless otherwise specified Group A subgroups Device type Limits 2/ Unit Min MaxPerf
48、ormance tests continued. CMIR 3/ 1,2 01 -2.0 +2.0 V Common mode input voltage range 3 -1.4 +1.4 Output current IOUT3/ 1,2 01 45 mA 3 25 1/ Unless otherwise specified, VCC= 5 V dc, AV= +2, load resistance (RL) = 100 , feedback resistance (RF) = 634 and gain resistance (RG) = 634 2/ The algebraic convention, whereby the most negati
