1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changes in accordance with NOR 5962-R136-97. - JB 96-11-20 Monica L. Poelking B Add limit for linear energy threshold (LET) with no latch-up in section 1.5. Update the boilerplate to the requirements of MIL-PRF-38535. Editorial changes throughout
2、. - TVN 07-01-22 Thomas M. Hess REV SHET REV B B SHET 15 16 REV B B B B B B B B B B B B B B REV STATUS OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder CHECKED BY Thanh V. Nguyen DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil APPR
3、OVED BY Monica L. Poelking DRAWING APPROVAL DATE 96-04-19 MICROCIRCUIT, DIGITAL, RADIATION HARDENED, ADVANCED CMOS, DUAL 4-INPUT NOR GATE, MONOLITHIC SILICON SIZE A CAGE CODE 67268 5962-96596 STANDARD MICROCIRCUIT DRAWING THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS AND AGENCIES OF THE DEPAR
4、TMENT OF DEFENSE AMSC N/A REVISION LEVEL B SHEET 1 OF 16 DSCC FORM 2233 APR 97 5962-E178-07 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVIS
5、ION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the P
6、art or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 H 96596 01 V X A Federal RHA Device Device Case Lead stock class designator type class outline finish designato
7、r (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-P
8、RF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACS4002 Radiation hardened, dual 4-
9、input NOR gate 1.2.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircui
10、ts in accordance with MIL-PRF-38535, appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style C GDIP1-T14 or CDIP2-T14 14 Dual-in-line
11、X CDFP3-F14 14 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROC
12、IRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VDD) -0.3 V dc to +7.0 V dc DC input voltage range (VIN) -0.3 V dc to VDD + 0.3 V dc DC output voltage range (VOUT) . -0
13、.3 V dc to VDD+ 0.3 V dc DC input current, any one input (IIN). 10 mA Latch-up immunity current (ILU) 150 mA Storage temperature range (TSTG) . -65C to +150C Lead temperature (soldering, 5 seconds). +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) +175C Ma
14、ximum power dissipation (PD) . 1.0 W 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VDD) +4.5 V dc to +5.5 V dc Input voltage range (VIN) 0.0 V dc to VDDOutput voltage range (VOUT). 0.0 V dc to VDDMaximum input rise or fall time at VDD= 4.5 V (tr, tf) 1 ns/V 4/ Case operating temp
15、erature range (TC). -55C to +125C 1.5 Radiation features. 5/ Total dose 1 x 106Rads (Si) Single event phenomenon (SEP) effective: Linear energy threshold (LET), no upsets (see 4.4.4.4). 80 MeV/(mg/cm2) Linear energy threshold (LET), no latch-up (see 4.4.4.4). 120 MeV/(mg/cm2) Dose rate upset (20 ns
16、pulse) 1 x 109Rads (Si)/s Latch-up. None Dose rate survivability 1 x 1012Rads (Si)/s 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Unless otherwise specified, all vol
17、tages are referenced to VSS. 3/ The limits for the parameters specified herein shall apply over the full specified VDDrange and case temperature range of -55C to +125C unless otherwise specified. 4/ Derate system propagation delays by difference in rise time to switch point for tror tf 1 ns/V. 5/ Ra
18、diation testing is performed on the standard evaluation circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FO
19、RM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitati
20、on or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEF
21、ENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Ave
22、nue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spec
23、ific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM p
24、lan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, con
25、struction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal connec
26、tions shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figur
27、e 4. 3.2.6 Irradiation test connections. The irradiation test connections shall be as specified in table III. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post irradiation parameter
28、limits are as specified in table IA and shall apply over the full case operating temperature range. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-39
29、90 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table IA. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein.
30、 In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be mar
31、ked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-3
32、8535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (
33、see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for t
34、his drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device
35、 classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving
36、devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offsh
37、ore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 36 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproductio
38、n or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 6 DSCC FORM 2234 APR 97 TABLE IA. Electrical performance characteristics. Limits 2/ Test Symbol Test conditions 1/ -5
39、5C TC +125C unless otherwise specified Device type VDDGroup A subgroups Min Max Unit All 1, 2, 3 3.15 M, D, P, L, R, F, G, H 3/ All 4.5 V 1 3.15 All 1, 2, 3 3.85 High level input voltage VIH M, D, P, L, R, F, G, H 3/ All 5.5 V 1 3.85 V All 1, 2, 3 1.35 M, D, P, L, R, F, G, H 3/ All 4.5 V 1 1.35 All
40、1, 2, 3 1.65 Low level input voltage VIL M, D, P, L, R, F, G, H 3/ All 5.5 V 1 1.65 V For all inputs affecting output under test, VIN= VDDor VSSIOH= -100 A All 1, 2, 3 4.25 High level output voltage VOH M, D, P, L, R, F, G, H 3/ All 4.5 V 1 4.25 V For all inputs affecting output under test, VIN= VDD
41、or VSSIOL= 100 A All 1, 2, 3 0.25 Low level output voltage VOL M, D, P, L, R, F, G, H 3/ All 4.5 V 1 0.25 V For input under test, VIN= VDDFor all other inputs, VIN= VDDor VSSAll 1, 2, 3 +1.0 Input current high IIH M, D, P, L, R, F, G, H 3/ All 5.5 V 1 +1.0 A For input under test, VIN= VSSFor all oth
42、er inputs, VIN= VDDor VSSAll 1, 2, 3 -1.0 Input current low IIL M, D, P, L, R, F, G, H 3/ All 5.5 V 1 -1.0 A For output under test, VOUT= VDD - 0.4 V VIN= VDDor VSSAll 1, 2, 3 -8.0 Output current (source) IOH4/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 1 -8.0 mA For output under test, VOUT= 0.4
43、V VIN= VDDor VSSAll 1, 2, 3 8.0 Output current (sink) IOL4/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 1 8.0 mA VIN= VDDor VSSAll 1, 2, 3 10.0 Quiescent supply current IDDQM, D, P, L, R, F, G, H 3/ All 5.5 V 1 10.0 A Short circuit output current IOS5/ 6/ VOUT= VDDand VSSAll 5.5 V 1, 2, 3 200 mA S
44、ee footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SIZE A 5962-96596 STANDARD MICROCIRCUIT DRAWING DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 7 DSCC FORM 2234 APR 97 TABLE IA. Electrical
45、 performance characteristics Continued. Limits 2/ Test Symbol Test conditions 1/ -55C TC +125C unless otherwise specified Device type VDDGroup A subgroups Min Max Unit Input capacitance CINf = 1 MHz See 4.4.1c All 0.0 V 4 15.0 pF Output capacitance COUTf = 1 MHz See 4.4.1c All 0.0 V 4 15.0 pF CL= 50
46、 pF, per switching output All 4, 5, 6 1.9 Switching power dissipation PSW7/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 4 1.9 mW/MHzVIH= 0.7 VDD, VIL= 0.3 VDD See 4.4.1b All 7, 8 L H Functional test 8/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 7 L H CL= 50 pF minimum See figure 4 All 9, 10, 11
47、 2.0 14.0 tPLH9/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 9 2.0 14.0 CL= 50 pF minimum See figure 4 All 9, 10, 11 1.0 12.0 Propagation delay time, any input to output tPHL9/ M, D, P, L, R, F, G, H 3/ All 4.5 V and 5.5 V 9 1.0 12.0 ns 1/ Each input/output, as applicable, shall be tested at the s
48、pecified temperature, for the specified limits, to the tests in table IA herein. Output terminals not designated shall be high level logic, low level logic, or open, except for the IDDQtest, the output terminals shall be open. When performing the IDDQtest, the current meter shall be placed in the circuit such that all current flows through the meter. 2/ For negative and positive voltage and current values, the sign designates the potential difference in reference to VSSand the direction of current flow, respectively; and the absolute value of the
