1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Update boilerplate to MIL-PRF-38535 requirements. - CFS 05-10-04 Thomas M. Hess REV A A A A A A A A A A A A A SHEET 75 76 77 78 79 80 81 82 83 84 85 86 87 REV A A A A A A A A A A A A A A A A A A A A SHEET 55 56 57 58 59 60 61 62 63 64 65 66 67 68
2、 69 70 71 72 73 74 REV A A A A A A A A A A A A A A A A A A A A SHEET 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 43 54 REV A A A A A A A A A A A A A A A A A A A A SHEET 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1
3、2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Larry T. Gauder DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY Thanh Nguyen COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICROCIRCUIT,
4、DIGITAL, 32-BIT INTEGRATED COMMUNICATION CONTROLLER, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 98-07-01 SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-97607 SHEET 1 OF 87 DSCC FORM 2233 APR 97 5962-E405-05Provided by IHSNot for ResaleNo reproduction or
5、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents two product assurance class levels consisting of high
6、reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. Th
7、e PIN is as shown in the following example: 5962 - 97607 01 M X X Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2)Device class designatorCase outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q and V RHA m
8、arked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Dev
9、ice type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 68EN360-25 MHz 32-bit integrated communication controller 02 68EN360-33.34 MHz 32-bit integrated communication controller 1.2.3 Device class designator. The device class designato
10、r is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q or V Certification and
11、 qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style X CMGA10-P241 241 pin grid array Y See figure 1 240 ceramic leaded chip carrier, gullwing-lead 1.2.5 Lead finish.
12、 The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEFENSE SUPPLY CENTER COLUMB
13、US COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Storage temperature range (TSTG) . -55C to +150C Supply voltage range (VCC) 2/ . -0.3 V dc to +6.5 V dc Input voltage range (VIN) 2/ . -0.3 V dc to +6.5 V dc Power dissipation (PD) . 2W Therm
14、al resistance, junction to case (JC): Case X 7C/W Case Y 2C/W Lead temperature range (soldering, 5 seconds). 270C 1.4 Recommended operating conditions. Case operating temperature range -55C to +125C Supply voltage range (VCC) 4.75 V dc VCC 5.25 V dc System frequency: Device type 01 25 MHz Device typ
15、e 02 33.34 MHz 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitati
16、on or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEF
17、ENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or http:/assist.daps.dla.mil or from the Standardization Document Order Desk, 700 Robbins Ave
18、nue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a spec
19、ific exemption has been obtained. _ 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 2/ Although sections of the device contain circuitry to protect against damage from hig
20、h static voltages or electrical fields, take normal precautions to avoid exposure to voltages higher than maximum rated voltages. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEFENSE SUPPLY CENTER CO
21、LUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Mana
22、gement (QM) plan. The modification in the QM plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construc
23、tion, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 herei
24、n and figure 1. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Block diagram. The block diagram shall be as specified on figure 3. 3.2.4 Timing waveforms. The timing waveforms shall be as specified on figure 4. 3.3 Electrical performance characteristics
25、 and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electrical test requirements. The electrical test
26、requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN n
27、umber is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance with MIL-PRF-38535. Marking for device clas
28、s M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6
29、Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer i
30、n order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q and V, the requirement
31、s of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided wit
32、h each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification an
33、d review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group a
34、ssignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 105 (see MIL-PRF-38535, appendix A).Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEF
35、ENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxInput high voltage (except EXTAL) VIH
36、1, 2, 3 All 2.0 VCCV Input low voltage (5 V part) VIL1, 2, 3 All GND 0.8 V Input low voltage (3.3 V part only; PA8-15, PB1, PCS5, PC7, TCK) VIL1, 2, 3 All GND 0.5 V Input low voltage (3.3 V part only; all other pins) VIL1, 2, 3 All GND 0.8 V Input high voltage EXTAL VIHC1, 2, 3 All 0.8 VCCVCC+0.3 V
37、Undershoot US1, 2, 3 All -0.8 V Input leakage current IINAll input only pins except for TMS,TDI, and TRST VIN= VCC= or GND 1, 2, 3 All -2.5 2.5 A OFF-STATE leakage current IOZAll non-crystal outputs and I/O pins, VIN= 0.5/2.4 V 1, 2, 3 All -20 20 A Signal low input current ILVIL= 0.8 V, (TMS, TDI, a
38、nd TRST pins only) 1, 2, 3 All -0.5 0.5 mA Signal high input current IHVIH= 2.0 V (TMS, TDI, and TRST pins only) 1, 2, 3 All -0.5 0.5 mA Output high voltage VOHIOH= -0.8 mA , VCC= 4.75 V 1, 2, 3 All 2.4 V IOL= 2.0 mA, CLKO1-2, FREEZE, IPIPEO-1, IFETCH, BKPTO 0.5 TOL= 5.3 mA, DSACK0-1, R/W, DS, OE, R
39、MC, BG, BGACK, BERR 0.5 TOL= 7 mA, TXD1-4 0.5 IOL= 8.9 mA, PB6, PB7, HALT, RESET, BR (Output) 0.5 Output low voltage (For 5 V part) VOLTOL= 3.2 mA, A31-A0, D31-D0, FC3-0, SIZ0-1, PA0, 2, 4, 6, 8-15, PB0-5 PB8-17, PC0-11, TDO, PERR, PRTY0-3, IOUT0-2, AVECO, AS, CAS3-0, BLCRO, RAS0-7 1, 2, 3 All 0.5 V
40、 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrica
41、l performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxInput capacitance All I/O pins CIN4 All 20 pF Load capacitance (except CLKO1-2) CLSee 4.4.1b 4 All 100 pF Load capacitance (CLKO1-2) CLc 4 All 5
42、0 pF Power (For 5 V version) VCC1, 2, 3 All 4.75 5.25 V Power (For 3.3 V version) VCC1, 2, 3 All 3.0 3.6 V Functional tests See 4.4.1c 7, 8 All Minimum VCCramp up time on power reset tRAMP9, 10, 11 All 4 mSec AC ELECTRICAL SPECIFICATIONS CONTROL TIMING 39/ VCC= 5.0 V, 25 MHz 9, 10, 11 01 dc 41/ 25 S
43、ystem frequency fSYSVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 33.34 MHz VCC= 5.0 V, 25 MHz 9, 10, 11 01 25 6000 Crystal frequency fXTALVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 25 6000 KHz VCC= 5.0 V, 25 MHz 9, 10, 11 01 20 50 On-chip VCO system frequency fSYSVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 20 67 MHz Start-up
44、time, with external clock (oscillator disabled) or after changing the multiplication factor MF tpllVCC= 5.0 V, 25 MHz 9, 10, 11 01 2500 clks CLKO1-2 stability CLKVCC = 5.0 V, 25 MHz 9, 10, 11 01 TBD TBD % VCC= 5.0 V, 25 MHz 9, 10, 11 01 40 (1) CLKO1 period tCYCVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 30 n
45、s VCC= 5.0 V, 25 MHz 9, 10, 11 01 40 60 (1A) EXTAL duty cycle, MF tdcycVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 40 60 % VCC= 5.0 V, 25 MHz 9, 10, 11 01 40 (1C) External clock input period tEXTcycVCC= 5.0 V, 33.34 MHz 9, 10, 11 02 30 ns VCC= 5.0 V, 25 MHz 9, 10, 11 01 19 (2,3) CLKO1 pulse width (measured a
46、t 1.5 V) tCW1VCC= 5.0 V, 33.34 MHz 9, 10, 11 02 14 ns VCC= 5.0 V, 25 MHz 9, 10, 11 01 9.5 (2A,3A) CLKO2 pulse width (measured at 1.5 V) tCW2VCC= 5.0 V, 33.34 MHz 9, 10, 11 02 7 ns VCC= 5.0 V, 25 MHz 9, 10, 11 01 2 (4,5) CLKO1 rise and fall times (Full drive) tCrf1VCC= 5.0 V, 33.34 MHz 9, 10, 11 02 2
47、 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-97607 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electr
48、ical performance characteristics - Continued. Test Symbol Conditions -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min MaxAC ELECTRICAL SPECIFICATIONS CONTROL TIMING - Continued. 39/ VCC= 5.0 V, 25 MHz 9, 10, 11 01 2 (4A,5A) CLKO2 rise and fall times (Full drive)
49、 tCrf2VCC= 5.0 V, 33.34 MHz 9, 10, 11 02 2 ns (5B) EXTAL to CLKO1 Skew-PLL enabled (MF5) tEXTP1VCC= 5.0 V, 25 MHz and 33.34 MHz 9, 10, 11 All 40/ ns (5C) EXTAL to CLKO2 Skew-PLL enabled (MF5) tEXTP2VCC= 5.0 V, 25 MHz and 33.34 MHz 9, 10, 11 All 40/ ns (5D) CLKO1 to CLKO2 Skew tCSKWVCC= 5.0 V, 25 MHz and 33.34 MHz 9, 10, 11 Al
