1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Drawing updated to reflect current requirements. - gt 02-06-17 Raymond Monnin REV SHET REV A A A A SHEET 15 16 17 18 REV STATUS REV A A A A A A A A A A A A A A OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY RICK OFFICER DEF
2、ENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY RAJESH PITHADIA COLUMBUS, OHIO 43216 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY RAYMOND MONNIN MICROCIRCUIT, DIGITAL-LINEAR, RADIATION HARDENED DUAL NON-INVERTING MOSFET AND AGENCIES OF
3、THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 99-06-02 DRIVER, MONOLITHIC SILICON AMSC N/A REVISION LEVEL A SIZE A CAGE CODE 67268 5962-99560 SHEET 1 OF 18 DSCC FORM 2233 APR 97 5962-E384-02 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited.Provided by IHSNot for Res
4、aleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents three product assurance class lev
5、els consisting of high reliability (device classes Q and M), space application (device class V) and for appropriate satellite and similar applications (device class T). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available
6、, a choice of Radiation Hardness Assurance (RHA) levels are reflected in the PIN. For device class T, the user is encouraged to review the manufacturers Quality Management (QM) plan as part of their evaluation of these parts and their acceptability in the intended application. 1.2 PIN. The PIN is as
7、 shown in the following example: 5962 F 99560 01 V X C Federal stock class designator RHA designator (see 1.2.1) Devicetype (see 1.2.2) Device class designator Caseoutline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q, T, and V RHA marked d
8、evices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device typ
9、e(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 HS-4424RH Radiation hardened dual non-inverting MOSFET drivers with 10 V lockout voltage 02 HS-4424BRH Radiation hardened dual non-inverting MOSFET drivers with 7.5 V lockout voltage 1.2
10、.3 Device class designator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance w
11、ith MIL-PRF-38535, appendix A Q, V Certification and qualification to MIL-PRF-38535 T Certification and qualification to MIL-PRF-38535 with performance as specified in the device manufacturers approved quality management plan. 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1
12、835 and as follows: Outline letter Descriptive designator Terminals Package style X CDFP4-F16 16 Flat pack 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q, T, and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction
13、or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ Supply voltage range (VS). 10 V to 20 V Input voltage range (V
14、IN). -0.3 V to +V 2/ Output short circuit duration (single supply) Continuous 3/ Maximum junction temperature (TJ) 175C Maximum storage temperature -65C to +150C Maximum lead temperature (soldering 10 seconds) 265C Thermal resistance, junction-to-case (JC) . 18C/W Thermal resistance, junction-to-amb
15、ient (JA) 90C/W 4/ 1.4 Recommended operating conditions. Supply voltage range (VS). 12 V to 18 V Low voltage lockout voltage: Device type 01 . 10.0 V Device type 02 . 7.5 V Operating temperature range -55C to +125C 1.5 Radiation features. SEP effective let no upsets TBD Maximum total dose available:
16、 (dose rate = 50 - 300 rad(Si) / s) Device classes M, Q, and V . 300 Krads (Si) Device class T 100 Krads (Si) Latch up immune. 5/ 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the e
17、xtent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATION DEPARTMENT OF DEFENSE MIL-PRF-38535 - Integrate
18、d Circuits, Manufacturing, General Specification for. STANDARDS DEPARTMENT OF DEFENSE MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. 1/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extend
19、ed operation at the maximum levels may degrade performance and affect reliability. 2/ Inputs must not go more negative than -0.3V. 3/ Short circuit from the output to VScan cause excessive heating and eventual destruction. 4/ JAis measured with the component mounted on an evaluation PC board in free
20、 air. 5/ Guaranteed by process or design. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 4 DSCC FORM 2234 APR 97 HANDBOOK
21、S DEPARTMENT OF DEFENSE MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Unless otherwise indicated, copies of the specification, standards, and handbooks are available from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D
22、, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption h
23、as been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q, T, and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM plan shall no
24、t affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. 3.1.1 Microcircuit die. For the requirements for microcircuit die, see appendix A to this document. 3.2 Design,
25、construction, and physical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q, T, and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with
26、 1.2.4 herein. 3.2.2 Terminal connection(s). The terminal connection(s) shall be as specified on figure 1. 3.2.3 Logic diagram(s). The logic diagram(s) shall be as specified on figure 2. 3.2.4 Truth table. The truth table shall be as specified in figure 3. 3.2.5 Radiation exposure circuit. The radia
27、tion exposure circuit shall be as specified on figure 4. 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply ove
28、r the full case operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In ad
29、dition, the manufacturers PIN may also be marked as listed in MIL-HDBK-103. For packages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designato
30、r shall still be marked. Marking for device classes Q, T, and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q, T, and V shall be a “QML“ or
31、“Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q, T, and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to th
32、e requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an
33、 approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q, T, and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. Provided by IHSNot for ResaleNo reproduction or
34、 networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions 1/ -55C TC +125C unless o
35、therwise specified Group A subgroups Device type Limits Unit Min Max Power supply current, low ICCSBVS= 18 V, inputs = 0 V 1 01,02 3.5 mA low 2,3 4.0 M,D,P,L,R,F 2/ 1 4.0 Power supply current, high ICCSBVS= 18 V, inputs = 18 V 1 01,02 3.5 mA high 2,3 4.0 M,D,P,L,R,F 2/ 1 4.0 Input current, low IILVS
36、= 18 V 1 01,02 2 A 2,3 4 M,D,P,L,R,F 2/ 1 4 Input current, high IIHVS= 18 V 1 01,02 2 A 2,3 4 M,D,P,L,R,F 2/ 1 4 Voltage output VOL, VS= 12 1 01,02 VS 0.75 0.8 V VOH2,3 VS 0.75 0.8 M,D,P,L,R,F 2/ 1 VS 0.75 0.8 Input voltage VIL, VS= 12 V, 1 01,02 3.0 0.4 V VIHlimits applied during 2,3 3.5 0.4 functi
37、onal test M,D,P,L,R,F 2/ 1 3.5 0.4 Functional test FTVS= 12 V, VS= 18 V 7,8A,8B 01,02 M,D,P,L,R,F 2/ 7 See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTE
38、R COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics Continued. Test Symbol Conditions 1/ -55C TC +125C unless otherwise specified Group A subgroups Device type Limits Unit Min Max Propagation delay, low tPHLVS= 12 V, 9 0
39、1,02 250 ns CL= 4300 pF 10,11 350 M,D,P,L,R,F 2/ 9 350 Propagation delay, high tPLHVS= 12 V 9 01,02 250 ns CL= 4300 pF 10,11 350 M,D,P,L,R,F 2/ 9 350 Response time, rise TR VS= 12 V, 9 01,02 75 ns CL= 4300 pF 10,11 95 M,D,P,L,R,F 2/ 9 95 Response time, fall TF VS= 12 V, 9 01,02 75 ns CL= 4300 pF 10,
40、11 95 M,D,P,L,R,F 2/ 9 95 1/ VS= 12 V to 18 V. 2/ The devices supplied to this drawing meet all levels M, D, P, L, R, F of irradiation (classes M, Q, and V), and all levels M, D, P, L, R for class T. However, this device is only tested at the “F“ level (classes M, Q, and V) and for class T, “R” leve
41、l (see paragraph 1.5). Pre and Post irradiation values are identical unless otherwise specified in Table I. When performing post irradiation electrical measurements for any RHA level, TA= +25C. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q, T, and V in
42、 MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to
43、 this drawing is required for any change as defined in MIL-PRF-38535, appendix A. 3.9 Verification and review for device class M. For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore d
44、ocumentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 89 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reproduction or
45、networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 7 DSCC FORM 2234 APR 97 Device types 01 and 02 Case outline X Terminal number Terminal symbol 1 NC 2 INPUT A 3 NC 4 GND 56
46、 NC 7 INPUT B 8 NC 910 OUTPUT B 11 OUTPUT12 VS13 VS14 OUTPUT A 15 OUTPUT 16 NCFIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHI
47、O 43216-5000 REVISION LEVEL A SHEET 8 DSCC FORM 2234 APR 97 FIGURE 2. Logic diagram. INPUT A OUTPUT A 1 1 0 0 INPUT B OUTPUT B 1 1 0 0 FIGURE 3. Truth table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99
48、560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 9 DSCC FORM 2234 APR 97 NOTES: VS= 15 V and R1 = 5 k. FIGURE 4. Radiation exposure circuit. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-99560 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000 REVISION LEVEL A SHEET 10 DSCC FORM 2234 APR 97 4. QUALITY ASSURANCE PROVISIONS 4.1 Sampling and inspection. For device classes Q, and V, sampling and inspection pr
