1、A-A-53787 66 777777r 0033242 7 A-A-53 9 8 9 18 September 1989 COMMERCIAL ITEM DESCRIPTION CAP, SCREW, BOTTLE AND JAR The General Services Administration has authorized the use of this commercial item description in preference to Military Specification MIL-C-42061. This commercial item description co
2、vers one type of threaded closure cap for use with aircraft lubricants and hydraulic fluids. Salient characteristics. Shall be a closure cap for use in an oil analysis program for checking the condition of aircraft lubricants and hydraulic fluids. Material. Shall be fabricated from white urea materi
3、al (see Notes). Size. Construction. thread for closure on a glass bottle with a 24 millimeter GPI 400 finish (see Notes). shall have ribbed surfaces to facilitate gripping. ribbed surfaces shall cover at least (50) percent of the gripping surface. Durability. Shall be capable of withstanding a 14 da
4、y immersion in typical aircraft lubricants and hydraulic fluids without any evidence of deterioration that would cause softening, cracking or failure as a closure cap on a glass bottle holding aircraft lubricant or hydraulic fluid samples (see Notes) . Shall be a size 24-400 closure cap. Shall be a
5、closure cap with an internal The outside of the closure cap The Shall be supplied without a liner. AMSC N/A FSC 6640 DISTRIBUTION STATEMENT A. distribution is unlimited. Approved for public release; I . THIS DOCUMENT CONTAINS /-=& ?E*- Licensed by Information Handling ServicesA-A- 5 3 9 8 9 Intended
6、 use. Shall be suitable for use as a closure cap on a bottle used for transporting samples, and then as a specimen cup for evaluating a sample in an atomic emission spectrophotometer. As a specimen cup for use with an atomic emission spectrophotometer, shall be capable of withstanding heating of oil
7、 without evidence of melting or other types of deterioration (see Notes) . Workmansh-iE. detract from its appearance or impair its serviceability. CI_ Unit. Package (PG). One package containing 3600 caps, as specified, constitutes one unit. The screw cap shall be free from defects which Quality Assu
8、rance Provisions. Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use
9、 his own or any facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supp
10、lies and services conform to prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of th
11、e contract and for a period of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determ
12、ination by technical means of physical and chemical properties) of the item. Inspection and tests. Inspection and tests shall be conducted in accordance with commercial practice to determine compliance with specification requirements. Sampling for inspections and tests shall also be conducted in acc
13、ordance with commercial practice . 2 Licensed by Information Handling ServicesA-A-53 9 8 9 Metric products. Products manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerances specified using conver
14、sion tables contained in the latest revision of Federal Standard 376, and all other requirements of this document are met. dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is accep
15、table. The contracting officer has the option of accepting or rejecting the product. Contractor certification. The contractor shall certify that the product offered meets the salient-characteristics of this description and conforms to the producers own drawings, specifications, standards, and qualit
16、y assurance practices. The Government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. If a product is manufactured to metric Regulatory requirements. Federal Food, Druq and Cosmetic
17、Act. If the product covered by this document has been determined by the U. S. Food and Drug Administration to be under its jurisdiction, the offeror/ contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of the Federal Food, Drug and Cosmet
18、ic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Federal, State and local statutes, ordinances, and regulations. 0 Recovered m
19、aterials. The offeror/contractor is encouraged to use recovered material in accordance with Public Law 94-580, as amended, and as implemented by Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. Presemation, packaqing, packing, labelinq, and marking. Unless otherwise speci
20、fied, preservation, packaging, and packing shall - be to a degree of proiection to preclude damage to-containers and/or contents thereof under normal shipping conditions, handling, etc:, involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity, and
21、 shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities and labeling and marking shall be as specified in the contract and/or order. 3 Licensed by Information Handling ServicesA-A- 5 3 9 8 9 NOTE: This document covers the following item listed in the
22、 Federal Supply Catalog: - NSN Item Identification I 6640-01-042-6583 CAP, SCREW, BOTTLE AND JAR The following item listed in the Federal Supply Catalog is the bottle that is intended for use with the screw cap for transporting fluid samples. - NSN Item Identification 8125-00-933-4414 BOTTLE, SCREW
23、CAP The white urea material that is specified, is intended to withstand the heating of a fluid sample when used as a specimen cup in an atomic emission spectrophotometer. The whitish color is required in order to provide a contrasting color to facilitate a visual inspection of a fluid sample when th
24、e cap is used as a specimen cup. First article samples or pre-award samples, when required, may be forwarded for evaluation to the Technical Support Center for Joinst Analysis Program at the Naval Air Station (Pensacola, Florida), The evaluation will include a determination as to a caps capability f
25、or use as a specimen cup with a flame Spectrophotometer. The lollowing products, as of the date of this document, are purported by the following companies to meet the salient characteristics of the item described herein: Kerr Glass Manufacturing Corporation - Item 46124/DS 24-400 White Urea Cap Owen
26、s-Illinois/Closure Operation/ - Mold No. 2429 (white urea) Glass Container Div. Size 24-400 closure cap Ordering data. (Intermediate/exterior package quantities and labeling and marking must be specified in the contract and/or order) 4 Licensed by Information Handling ServicesA-A-53989 66 9997974 0011246 4 W . I I I. I I I MILITARY INTERESTS: b a Custodians: Army - MD Navy - MS Air Force - 99 5 PREPARING ACTIVITY: DOD - MB Agent: DLA-DM Project No. 6640-1584 A-A- 5 3 9 8 9 Licensed by Information Handling Services
