1、A-A-54887 9999974 OL4490b 895 = I INCH-POUND I 2 July 1993 A-A-5 4 88 7 COMMERCIAL ITEM DESCRIPTION SHIELD, EYE, SURGICAL, FOX The General Services Administration has authorized the use of this Commercial Item Description as a replace- ment of Federal Specification GG-S-325, which is to be cancelled
2、. This Commercial Item Description covers one type of eye shield to be worn by patient following ocular surgery for protecting inadvertent trauma. Salient characteristics: General. The shield shall be of the Fox design as shown in figure 1. It shall be made of sheet aluminum capable being molded by
3、hand to fit facial contours of patient. of the shield shall be oval with a series of evenly spaced ventilating holes on the center part. Slots shall be along the periphery for easy bending. The shield shall be pre- shaped into a cup form so that the highest part is at the center. The shape Material.
4、 The shield shall be made of pure aluminum or aluminum alloy with thickness of 20 gauge B distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54887 W 9999974 0344907 721 W A-A-54 a a 7 QUALITY ASSURANCE PROVISIONS. Responsi
5、bility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any facilities
6、 suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspection are deemed necessary to assure supplies and services conform t
7、o prescribed requirements. Records. Records of examinations and tests performed by or for the contractor shall be maintained by the contractor and made available to the Government upon the Governments request, at any time, or from time to time, during the performance of the contract and for a period
8、 of three years after delivery of the supplies to which such records relate. Inspection. Inspection, as used herein, is defined as both examination (such as visual or auditory investigation without the use of special laboratory appliances or procedures) and testing (determination by technical means
9、of physical and chemical properties) of the item. Examination. Examination shall be conducted to determine compliance with specification requirements. Samplins for examination. Sampling for examination shall be conducted in accordance with MIL-STD-105 and as specified. Unit of product for examinatio
10、n purposes shall be one shield as specified. Sampling shall be inspection level II with an Acceptable Quality Level (AQL) of 1.0. Tests. Tests shall be conducted to determine compliance with specification requirements. Where feasible, the same sample shall be used for determination of two or more te
11、st characteristics. Samplinq for tests. Sampling for tests shall be conducted in accordance with MIL-STD-105 and as specified. for test purposes shall be one shield. Sampling shall be inspection level S-2 with an AQL of 1.0. Unit of product 2 Provided by IHSNot for ResaleNo reproduction or networkin
12、g permitted without license from IHS-,-,-A-A-54887 m 9999974 0344908 bb8 m A-A-5 4 8 8 7 Contractor certification. The contractor shall certify and maintain substantiating evidence that the product offered meets the salient characteristics of this Commercial Item Description, and that the product co
13、nforms to the producers own drawings, specifications, standards, and quality assurance practices. The government reserves the right to require proof of such conformance prior to first delivery and thereafter as may be otherwise provided for under the provisions of the contract. Metric products. Prod
14、ucts manufactured to metric dimensions will be considered on an equal basis with those manufactured using inch-pound units, providing they fall within the tolerance specified using conversion tables contained in the latest revision of Federal Standard No. 376, and all other requirements of this docu
15、ment are met. If a product is manufactured to metric dimensions and those dimensions exceed the tolerances specified in the inch-pound units, a request should be made to the contracting officer to determine if the product is acceptable. The contracting officer has the option of accepting or rejectin
16、g the product. - Requlatory requirements. Federal Food, Druq, and Cosmetic Act. If the product covered by this document has been determined by the U.S. Food and Drug Administration to be under its jurisdiction, the offeror/contractor shall comply, and be responsible for compliance by its subcontract
17、ors/suppliers, with the requirements of the Federal Food, Drug and Cosmetic Act, as amended, and regulations promulgated thereunder. In addition, the offeror/contractor shall comply, and be responsible for compliance by its subcontractors/suppliers, with the requirements of all other applicable Fede
18、ral, State, and local statutes, ordinances, and regulations. Recovered materials. The offeror/contractor is encouraged to use recovered material in accordance with Federal Acquisition Regulation Subpart 23.4 to the maximum extent practical. 3 Provided by IHSNot for ResaleNo reproduction or networkin
19、g permitted without license from IHS-,-,-A-A-54887 m 9999974 OL44909 5T4 m A-A-54 8 8 7 Preservation, packaqinq, p ackinq, labelinq, and markinq. Unless otherwise specified, preservation, packaging, and packing shall be to a degree of protection to preclude damage to containers and/or contents there
20、of under normal shipping conditions, handling, etc., involving shipment from the supply source to the receiving activity, plus reshipment from receiving activity and shall conform to applicable carriers rules and regulations. Intermediate and exterior package quantities *and labeling and marking sha
21、ll be as specified in the contract and/or order. Orderinq data. Intermediate/exterior package quantities and labeling and marking must be specified in the contract and/or order. NOTE: The following National Stock Number and its respective Item Identification is covered by this document: NATIONAL STO
22、CK NUMBER ITEM IDENTIFICATION 6515-00-663-9801 SHIELD, EYE, SURGICAL, FOX MILITARY INTERESTS: Preparing Activity: Custodians: DoD-MB Army - MD Navy - MS Air Force - 03 CIVIL AGENCY COORDINATING ACTIVITIES: VA-OSS USPHS FDA-MPQAS GSA-FSS-FCGC Agent: DLA-DM Project Number: 6515-5600 Location: c:worddocsetoshieldsg 4 I Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-54887 i -I ao Q) m L Y _. E 9999974 OL449LO 2Lb E S W X- O LL -1 W a 2 L88VS-Q-Q Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
