1、 EIA STANDARD Fixed Capacitors for Use in Electronic Equipment Part 25: Sectional Specification Surface Mount Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte EIA-60384-25 (IEC 60384-25:2006, IDT) September 2014 ANSI/EIA-60384-252014 Approved: September 30, 2014 EIA-
2、60384-25 NOTICE EIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaining with mi
3、nimum delay the proper product for his particular need. Existence of such Standards and Publications shall not in any respect preclude any member or nonmember of ECIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of such Standards a
4、nd Publications preclude their voluntary use by those other than ECIA members, whether the standard is to be used either domestically or internationally. Standards and Publications are adopted by ECIA in accordance with the American National Standards Institute (ANSI) patent policy. By such action,
5、ECIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This EIA Standard is identical (IDT) with the International Standard IEC Publication 60384-25:2006: Fixed Capacitors for Use in Electronic Equipment Par
6、t 25: Sectional Specification Surface Mount Fixed Aluminium Electrolytic Capacitors with Conductive Polymer Solid Electrolyte. This document is the EIA Standard EIA-60384-25 2014 Edition 1: Fixed Capacitors for Use in Electronic Equipment Part 25: Sectional Specification Surface Mount Fixed Aluminiu
7、m Electrolytic Capacitors with Conductive Polymer Solid Electrolyte. The text, figures and tables of IEC 60384-25:2006 are used in this Standard with the consent of the IEC and the American National Standards Institute (ANSI). The IEC copyrighted material has been reproduced with permission from ANS
8、I. The IEC Foreword and Introduction are not part of the requirements of this standard but are included for information purposes only. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user
9、 of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 5267, formulated under the cognizance of the P-2.5 Committee on EIA Solid Electrolytic Capacitors Standards and given final
10、 approval by the Standards Steering Committee for Passive Electronic Components Standards (S-1). Published by Electronic Components Industry Association 2014 Engineering Department 2214 Rock Hill Road, Suite 265 Herndon, VA 20170 PLEASE! DONT VIOLATE THE LAW! This document is copyrighted by the ECIA
11、 and may not be reproduced without permission. Organizations may obtain permission to reproduce a limited number of copies through entering into a license agreement. For information, contact: IHS 15 Inverness Way East Englewood, CO 80112-5704 or call USA and Canada (1-877-413-5184), International (3
12、03-397-7956) IEC 60384-25 (First edition 2006) Fixed capacitors for use in electronic equipment Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte CORRIGENDUM Page 6 1.3 Normative references Delete the following reference:
13、 IEC 62378, Capacitors and resistors Conformity assessment procedures Generic standard Page 10 3.4.1 Qualification approval on the basis of the fixed sample size procedures Delete the first sentence. October 2006 i CONTENTS FOREWORD 1 1 General . 4 1.1 Scope . 4 1.2 Object . 4 1.3 Normative referenc
14、es 4 1.4 Information to be given in a detail specification . 5 1.5 Terms and definitions 6 1.6 Marking . 6 2 Preferred rating and characteristics . 6 2.1 Preferred characteristics 6 2.2 Preferred values of ratings . 7 3 Quality assessment procedures 7 3.1 Primary stage of manufacture 7 3.2 Structura
15、lly similar components 7 3.3 Declaration of conformity (basic requirements) . 8 3.4 Test schedule and requirement for initial assessment (mandatory and optional tests) . 8 3.5 Quality conformance inspection 17 4 Test and measurement procedures . 19 4.1 Preliminary drying . 19 4.2 Measuring condition
16、s . 19 4.3 Mounting . 19 4.4 Visual examination and check of dimensions. 19 4.5 Electrical tests . 19 4.6 Resistance to soldering heat 21 4.7 Solderability 22 4.8 Shear test . 22 4.9 Substrate bending test . 22 4.10 Rapid change of temperature . 22 4.11 Climatic sequence . 23 4.12 Damp heat, steady
17、state 23 4.13 Characteristics at high and low temperature 24 4.14 Surge 24 4.15 Endurance 24 4.16 Storage at high temperature . 25 4.17 Charge and discharge (if required by the detail specification) 25 4.18 Component solvent resistance (if applicable) 26 4.19 Solvent resistance of the marking (if ap
18、plicable) 26 4.20 High surge current (if applicable) 26 EIA-60384-25 Page 1 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ FIXED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte FO
19、REWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the e
20、lectrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to
21、technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International O
22、rganization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each techn
23、ical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publi
24、cations is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their nati
25、onal and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any equipment declared to b
26、e in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committ
27、ees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to t
28、he Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of patent rights. IEC shall not be hel
29、d responsible for identifying any or all such patent rights. International Standard IEC 60384-25 has been prepared by IEC technical committee 40: Capacitors and resistors for electronic equipment. The text of this standard is based on the following documents: FDIS Report on voting 40/1733/FDIS 40/17
30、56/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. EIA-60384-25 Page 2 IEC 60384 consists of the following parts, under the gen
31、eral title Fixed capacitors for use in electronic equipment: Part 1: Generic specification Part 2: Sectional specification: Fixed metallized polyethylene-terephthalate film dielectric d.c. capacitors Part 3: Sectional specification: Fixed tantalum chip capacitors Part 4: Sectional specification: Alu
32、minium electrolytic capacitors with solid and non-solid electrolyte Part 5: Sectional specification: Fixed mica dielectric d.c. capacitors with a rated voltage not exceeding 3 000 V Selection of methods of test and general requirements Part 6: Sectional specification: Fixed metallized polycarbonate
33、film dielectric d.c. capacitors Part 7: Sectional specification: Fixed polystyrene film dielectric metal foil d.c. capacitors Part 8: Sectional specification: Fixed capacitors of ceramic dielectric, Class 1 Part 9: Sectional specification: Fixed capacitors of ceramic dielectric, Class 2 Part 11: Sec
34、tional specification: Fixed polyethylene-terephthalate film dielectric metal foil d.c. capacitors Part 12: Sectional specification: Fixed polycarbonate film dielectric metal foil d.c. capacitors Part 13: Sectional specification: Fixed polypropylene film dielectric metal foil d.c. capacitors Part 14:
35、 Sectional specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains Part 15: Sectional specification: Fixed tantalum capacitors with non-solid or solid electrolyte Part 16: Sectional specification: Fixed metallized polypropylene film dielectric
36、d.c. capacitors Part 17: Sectional specification: Fixed metallized polypropylene film dielectric a.c. and pulse capacitors Part 18: Sectional specification: Fixed aluminium electrolytic chip capacitors with solid and non-solid electrolyte Part 19: Sectional specification: Fixed metallized polyethyle
37、ne-terephthalate film dielectric chip d.c. capacitors Part 20: Sectional specification: Fixed metallized polyphenylene sulphide film dielectric chip d.c. capacitors Part 21: Sectional specification: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 1 Part 22: Sectional specifica
38、tion: Fixed surface mount multilayer capacitors of ceramic dielectric, Class 2 Part 23: Sectional specification: Fixed surface mount metallized polyethylene naphthalate film dielectric d.c. capacitors Part 24: Sectional specification: Surface mount fixed tantalum electrolytic capacitors with conduct
39、ive polymer solid electrolyte Part 25: Sectional specification: Surface mount fixed aluminium electrolyte capacitors with conductive polymer solid electrolyte All sectional specifications mentioned above do have one or more blank detail specifications being a supplementary document, containing requi
40、rements for style, layout and minimum content of detail specifications. EIA-60384-25 Page 3 The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the s
41、pecific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. A bilingual version of this publication may be issued at a later date. The contents of the corrigendum of October 2006 have been included in this copy. EIA-60384-25 Page 4 FI
42、XED CAPACITORS FOR USE IN ELECTRONIC EQUIPMENT Part 25: Sectional specification Surface mount fixed aluminium electrolytic capacitors with conductive polymer solid electrolyte 1 General 1.1 Scope This part of IEC 60384 is applicable to aluminium electrolytic capacitors with conductive polymer solid
43、electrolyte. These capacitors are primarily intended to be mounted direct on substrates for hybrid circuits or to printed boards. Fixed aluminium electrolytic chip capacitors with solid (MnO2) are not included but are covered by IEC 60384-18. 1.2 Object The object of this standard is to prescribe pr
44、eferred ratings and characteristics and to select from IEC 60384-1:1999, the appropriate quality assessment procedures, tests and measuring methods and to give general performance requirements for this type of capacitor. Test severities and requirements prescribed in detail specifications referring
45、to this sectional specification shall be of equal or higher performance level; lower performance levels are not permitted. 1.3 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For und
46、ated references, the latest edition of the referenced document (including any amendments) applies. IEC 60063:1963, Preferred number series for resistors and capacitors Amendment 1 (1967) Amendment 2 (1977) IEC 60068-1: Environmental testing Part 1: General and guidance IEC 60068-2-58:2004, Environme
47、ntal testing Part 2-58: Tests Test Td: Test methods for solderability, resistance to dissolution of metallization and to soldering heat of surface mounting devices (SMD) IEC 60384-1:1999, Fixed capacitors for use in electronic equipment Part 1: Generic specification IEC 60410: Sampling plans and pro
48、cedures for inspection by attributes ISO 3:1973, Preferred numbers Series of preferred numbers EIA-60384-25 Page 5 1.4 Information to be given in a detail specification Detail specifications shall be derived from the relevant blank detail specification. Detail specifications shall not specify requir
49、ements inferior to those of the generic, sectional or blank detail specification. When more severe requirements are included, they shall be listed in 1.9 of the detail specification and indicated in the test schedules, for example, by an asterisk. NOTE The information given in 1.4.1 may, for convenience, be presented in tabular form. The following information shall be given in each detail specification and the values quoted shall preferably be selected from those given in the appropriate clause of this sectional specification. 1
