1、BRITISH STANDARDBS EN 10339:2007Steel tubes for onshore and offshore water pipelines Internal liquid applied epoxy linings for corrosion protectionThe European Standard EN 10339:2007 has the status of a British StandardICS 23.040.99; 25.220.60g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37
2、g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 10339:2007This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 March 2007 BSI 2007ISBN 978 0 58
3、0 50322 1National forewordThis British Standard was published by BSI. It is the UK implementation of EN 10339:2007.The UK participation in its preparation was entrusted to Technical Committee ISE/8, Steel pipes.A list of organizations represented on ISE/8 can be obtained on request to its secretary.
4、Compliance with this Standard does not automatically imply a presumption that the product is suitable for the transport of water intended for human consumption, within the meaning of European Directive 89/106/EEC (also known as the Construction Products Directive). Until the proposed European Accept
5、ance Scheme for construction products in contact with water intended for human consumption (or an alternative programme put forward by the European Commission) is in place, and this Standard revised to reflect this, products conforming to this Standard may be used in applications involving the trans
6、port of water for human consumption if they also conform to the relevant national, regional or local regulatory provisions applicable in the place of use. In the UK, products and processes need to be approved by the Drinking Water Inspectorate (DWI). This involves obtaining approvals under regulatio
7、n 31 for both the coating and the coating applicator. For more details please refer to http:/www.dwi.gov.uk/cpp/index.shtm.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard can
8、not confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 10339February 2007ICS 23.040.99; 25.220.60English VersionSteel tubes for onshore and offshore water pipelines - Internalliquid applied epoxy linings
9、for corrosion protectionTubes pour canalisations deau enterres et immerges -Revtements internes en rsine poxyde applique ltatliquide pour la protection contre la corrosionStahlrohre fr erd- und wasserverlegteWasserleitungssysteme - Innenauskleidung mitEpoxidharzen als KorrosionsschutzThis European S
10、tandard was approved by CEN on 20 December 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerni
11、ng such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own lang
12、uage and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe
13、mbourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights
14、 of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 10339:2007: EEN 10339:2007 (E) 2 Contents Page 1 Scope 4 2 Normative references 4 3 Terms and definitions .5 4 Symbols and abbreviations 5 5 Lining materials .5 5.1 General5 5.2 Technical specificati
15、on .5 5.3 Packaging .8 6 Information to be supplied by the purchaser .8 6.1 Mandatory.8 6.2 Options to be indicated by the purchaser.8 7 Surface preparation and application of the lining8 7.1 Surface preparation.8 7.2 Application of the lining9 8 Requirements of the applied lining10 8.1 General10 8.
16、2 Appearance and continuity.10 8.3 Minimum dry film thickness of the lining10 8.4 Hardness measured by Buchholz indentation .11 8.5 Non porosity.11 8.6 Adhesion.11 8.7 Cut back lengths11 8.8 Summary of the required properties .12 9 Repairs12 10 Marking .13 11 Handling, transportation and storage13 1
17、1.1 Handling and transportation to the storage area .13 11.2 Storage13 11.3 Loading of tubes for delivery .13 Annex A (normative) Adhesion test - Resistance to removal .14 A.1 General14 A.2 Apparatus .14 A.3 Procedure .14 A.4 Results 15 Bibliography 16 EN 10339:2007 (E) 3 Foreword This document (EN
18、10339:2007) has been prepared by Technical Committee ECISS/TC 29 “Steel tubes and fittings for steel tubes”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest b
19、y August 2007, and conflicting national standards shall be withdrawn at the latest by August 2007. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Cze
20、ch Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EN 10339:2007 (E) 4 1 Scope This European Standa
21、rd specifies the requirements for the application of liquid applied epoxy internal linings, for the corrosion protection of steel tubes. This type of lining is generally used in the transport and distribution, under pressure or by gravity, of water intended for human consumption and industrial use,
22、sea water, waste water and also in fire water. The temperature of the water transported generally does not exceed 50 C. The choice of the lining and its limits of use depend on the type of product used, the pipe laying conditions, the temperature and the chemical composition of the fluid. The choice
23、 of the product for the medium to be transported and its qualification are not part of this European Standard. The lining consists normally of one layer of liquid product, applied by spray airless technique after surface preparation. All or some of the requirements of this European Standard can appl
24、y to the internal linings of fittings, if agreed by the purchaser and the coater. The lining in this European Standard can be applied to longitudinally or spirally welded tubes and to seamless steel tubes used for the construction of pipelines for conveying liquids. These tubes are not intended to b
25、e bent after the epoxy lining has been applied. This European Standard does not cover in-situ applied or rehabilitation linings. The constituent materials of epoxy linings, when used under the conditions for which they are designed, in permanent or temporary contact with water intended for human con
26、sumption, should not change the quality of that water to such an extent that it fails to comply with the requirements of European regulations at the end user. For this purpose, reference should be made to the relevant national standards transposing EN standards when available, dealing with the influ
27、ence of materials on water quality. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments)
28、 applies. EN 1184, Materials and articles in contact with foodstuffs Test methods for translucency of ceramic articles EN ISO 2808, Paints and varnishes Determination of film thickness (ISO 2808:1997) EN ISO 2811-1, Paints and varnishes Determination of density Part 1: Pyknometer method (ISO 2811-1:
29、1997) EN ISO 2815, Paints and varnishes Buchholz indentation test (ISO 2815:2003) EN ISO 3251, Paints, varnishes and plastics Determination of non-volatile-matter content (ISO 3251:2003) EN ISO 4287, Geometrical product specification (GPS) Surface texture: Profile method Terms, definitions and surfa
30、ce texture parameters (ISO 4287:1997) EN ISO 4624, Paints and varnishes Pull-off test for adhesion (ISO 4624:2002) EN 10339:2007 (E) 5 EN ISO 8501-1, Preparation of steel substrates before application of paints and related products Visual assessment of surface cleanliness Part 1: Rust grades and pre
31、paration grades of uncoated steel substrates and of steel substrates after overall removal of previous coatings (ISO 8501-1:1988) EN ISO 8503-2, Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part
32、2: Method for the grading of surface profile of abrasive blast-cleaned steel Comparator procedure (ISO 8503-2:1988) EN ISO 8503-4, Preparation of steel substrates before application of paints and related products Surface roughness characteristics of blast-cleaned steel substrates Part 4: Method for
33、the calibration of ISO surface profile comparators and for the determination of surface profile Stylus instrument procedure (ISO 8503-4:1988) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 product manufacturer supplier of the epoxy materials
34、 in a condition suitable for application to the product to be coated 3.2 coater company responsible for applying the lining material to the components to be coated 3.3 purchaser company that buys the coated tubes and fittings 4 Symbols and abbreviations For the purposes of this document, the followi
35、ng symbol applies. Rzthe average roughness from five successive evaluation areas defined according to EN ISO 4287, expressed in microns (m) 5 Lining materials 5.1 General The lining material is generally composed of a base (epoxy resin) and a curing agent. A primer may be used when recommended by th
36、e product manufacturer. The base (epoxy resin) and curing agent should have different colours allowing the verification of the correct mixing by checking the uniformity of the colour of the mixed product. This European Standard calls for the use of substances and/or procedures that may be injurious
37、to health if precautions are not taken. It refers only to technical suitability and in no way absolves the user from statutory obligations relating to health and safety at any stage. 5.2 Technical specification The technical specification drawn up by the product manufacturer shall contain as a minim
38、um the information detailed in Table 1. Where testing standards are mentioned in Table 1, the data supplied by the product EN 10339:2007 (E) 6 manufacturer shall be according to these standards. Otherwise, test methods shall be given for any test detailed in Table 1. Tests shall be done to be consis
39、tent with the product manufacturers recommendations for application. Infrared scan of the product components shall be made available on request to the coater. Other data or tests can be agreed between the parties at the time of enquiry and/or order. If test certificates are required, they shall at l
40、east contain the data mentioned in Table 1. EN 10339:2007 (E) 7 Table 1 Contents of Technical data sheet and Test certificates Elements Technical data sheets Test certificatesDate of issue x x Name of manufacturer x x Field of application x Name and type of product x x Type of base (epoxy resin) x T
41、ype of curing agent x Factory of origin x Batch or production lot number xaUse by date xaColour xaMethods of application x Solids by volume x Solids by weight of the mixed product according EN ISO 3251 xbTheoretical coverage per m for nominal thickness x Shelf life xaStorage conditions x Pot-life x
42、Surface preparation x Recommended instructions for application x Recommended repair method(s) x Mixing instructions (induction time if applicable) x Recommended dry film thickness (nominal and range) x Maximum recommended dry film thickness applicable in one layer x Minimum and maximum overcoating t
43、ime x Range of application temperature (ambient, tube and product) and humidity x Specific curing requirements x Hardness measured by Buchholz indentation test according to EN ISO 2815 of cured lining measured x Time related to curing temperature to achieve the full curing x Viscosity x x cdDensity
44、according to EN ISO 2811-1 x d ex aElongation at break on free film according to EN 1184 x Pull-off test for adhesion according to EN ISO 4624 x a Required for the base (epoxy resin) and curing agents. b In contradiction to the curing cycle specified in EN ISO 3251, curing cycle of 2 days at 23 C 2
45、C will apply. c Required for the base (epoxy resin), curing agent and the mixed product. d The acceptable limits shall be mentioned in the test certificate. e Required for the base (epoxy resin), curing agent. For the mixed product, density can be calculated. EN 10339:2007 (E) 8 5.3 Packaging As a m
46、inimum requirement, all materials supplied for lining operations shall be suitably marked with the following details: the product manufacturers name; the name of the material; the batch number; the use-by date; the recommended storage conditions; the colour of the material. 6 Information to be suppl
47、ied by the purchaser 6.1 Mandatory The purchaser shall state in his enquiry and order the following minimum information: Tubes and fittings to be coated according to this European Standard. These shall be designated by reference to this European Standard. If applicable, the reference to the standard
48、 for the tube to which the lining is applied shall be added to this designation. EXAMPLE: 5 000 m of tube - EN 10224 of 406, 4-4, 0 Internal lining EN 10339; type of fluid to be transported; minimum dry film thickness of the lining (see 8.3); service temperature; 6.2 Options to be indicated by the p
49、urchaser Maximum number and dimensions of repairs (not including repairs due to destructive tests); cut back lengths (see 8.7). 7 Surface preparation and application of the lining 7.1 Surface preparation 7.1.1 Prior to abrasive blast cleaning, the steel surface shall be dry and free from contamination (oil, grease, temporary corrosion protection etc.) and surface defects (slivers, laminations etc.) detrimental to the surface or to the adhesion of the lining. 7.1.2 Tubes shall be abrasive blast cleaned.
