1、BSI Standards PublicationMetallic industrial pipingPart 1: GeneralBS EN 13480-1:2012 Incorporating corrigendum April 2016 BS EN 13480-1:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 13480-1:2012.It supersedes BS EN 13480-1:2002+A2:2008 which is withdrawn.
2、The UK participation in its preparation was entrusted to TechnicalCommittee PVE/10, Piping systems.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a contract. Users are respon
3、sible for its correctapplication. The British Standards Institution 2016.ISBN 978 0 580 92907 6ICS 23.040.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 31 July
4、 2012.Amendments/corrigenda issued since publicationDate Text affectedPublished by BSI Standards Limited 201630 April 2016 Implementation of CEN/CENELEC Correction Notice 27 August 2014: Pages 4, 12, 15 and 16correctedEUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 13480-1 June 2012 ICS 23.040.
5、01 Supersedes EN 13480-1:2002English Version Metallic industrial piping - Part 1: General Tuyauteries industrielles mtalliques - Partie 1: Gnralits Metallische industrielle Rohrleitungen - Teil 1: AllgemeinesThis European Standard was approved by CEN on 8 May 2012. CEN members are bound to comply wi
6、th the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Mana
7、gement Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same st
8、atus as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portug
9、al, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any
10、 means reserved worldwide for CEN national Members. Ref. No. EN 13480-1:2012: EEN 13480-1:2012 (E) Issue 3 (2014-08) 2 Contents Page Foreword 3 1 Scope 5 2 Normative references 5 3 Terms, definitions, symbols and units 6 3.1 Terms and definitions .6 3.2 Symbols and units .8 4 Interdependency of the
11、parts of the series .9 5 Classification of piping .9 5.1 General 9 5.2 Piping of category 0 11 5.3 Piping operating 0,5 bar .11 5.4 Special cases .11 6 Requirements for Piping systems 11 Annex A (informative) Maintenance of EN 13480 .12 A.1 Introduction 12 A.2 Scope and composition of the Working Gr
12、oup 12 A.3 Methods of Maintenance .12 A.3.1 Administration tools 12 A.3.2 Submission of queries and consultation of the experts13 A.4 Results of the consultation .13 A.4.1 Practical provisions for interpretations 13 A.4.2 Practical provisions for corrections 14 Annex Y (informative) History of EN 13
13、480-1 .15 Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 97/23/EC 16 Bibliography 17 BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 3 Foreword This document (EN 13480-1:2012) has been prepared by Technical Committee CEN/TC 2
14、67 “Industrial piping and pipelines”, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2012, and conflicting national standards shall be withdraw
15、n at the latest by December 2012. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document has been prepared under a mandate give
16、n to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. In this European Standard Annex A is informative. This Eur
17、opean Standard EN 13480 for metallic industrial piping consists of eight interdependent and not dissociable Parts which are: Part 1: General; Part 2: Materials; Part 3: Design and calculation; Part 4: Fabrication and installation; Part 5: Inspection and testing; Part 6: Additional requirements for b
18、uried piping; CEN/TR 13480-7, Guidance on the use of conformity assessment procedures; Part 8: Additional requirements for aluminium and aluminium alloy piping. Although these Parts may be obtained separately, it should be recognised that the Parts are inter-dependant. As such the manufacture of met
19、allic industrial piping requires the application of all the relevant Parts in order for the requirements of the Standard to be satisfactorily fulfilled. This European Standard will be maintained by a Maintenance MHD working group whose scope of working is limited to corrections and interpretations r
20、elated to EN 13480. BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 4 The contact to submit queries can be found at http:/www.unm.fr (en13480unm.fr). A form for submitting questions can be downloaded from the link to the MHD website. After subject experts have agreed an answer, the answer wi
21、ll be communicated to the questioner. Corrected pages will be given specific issue number and issued by CEN according to CEN Rules. Interpretation sheets will be posted on the website of the MHD. This document supersedes EN 13480-1:2002+A1:2005+A2:2007. This new edition incorporates the Amendments/t
22、he corrigenda which have been approved previously by CEN members, and the corrected pages up to Issue 17 without any further technical change. Annex Y provides details of significant technical changes between this European Standard and the previous edition. Amendments to this new edition may be issu
23、ed from time to time and then used immediately as alternatives to rules contained herein. It is intended to deliver a new Issue of EN 13480:2012 each year, consolidating these Amendments and including other identified corrections. Issue 3 (2014-08) includes the corrected pages listed in Annex Y. Acc
24、ording to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, German
25、y, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 5 1 Scope This European Standard s
26、pecifies the requirements for industrial piping systems and supports, including safety systems, made of metallic materials with a view to ensure safe operation. This European Standard is applicable to metallic piping above ground, ducted or buried, irrespective of pressure. This European Standard is
27、 not applicable to: Pipelines and their accessories; Stream waterways such as penstocks, pressure tunnels, pressure shaft for hydro-electric-installations and their related specific accessories; Piping for vehicles covered by the EEC type approval procedures as laid down in Directives 70/156/EEC 1,
28、74/150/EEC 2 and 92/61/EEC 3; Items specifically designed for nuclear use, failure of which may cause an emission of radioactivity; Well-control equipment used in the petroleum, gas or geothermal exploration and extraction industry and in underground storage which is intended to contain and/or contr
29、ol well pressure, including the piping; Piping of blast furnaces including the furnace cooling, hot blast recuperators, dust extractors and blast furnace exhaust gas scrubbers and direct reducing cupolas including the furnace cooling, gas converters and vacuum furnaces and pans for melting, re-melti
30、ng de-gassing and casting of steel and non ferrous metals; Enclosures for high voltage electrical equipment such as switchgear, control gear and transformers; Pressurized pipes for the containment of transmission systems such as for electrical power and telephone cables; Permanently fixed piping for
31、 ships, rockets, aircraft and mobile offshore units; Internal piping in medical devices as defined in the Directive 93/142/EEC 4 concerning medical devices; Internal piping of boilers and piping integral to pressure vessels. 2 Normative references The following documents, in whole or in part, are no
32、rmatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 764-2:2002, Pressure equipment Part 2: Quantities, symbo
33、ls and units BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 6 EN 764-3:2002, Pressure equipment Part 3: Definitions and parties involved EN 13480-2:2012, Metallic industrial piping Part 2: Materials EN 13480-3:2012, Metallic industrial piping Part 3: Design and calculation EN 13480-4:2012,
34、Metallic industrial piping Part 4: Fabrication and installation EN 13480-5:2012, Metallic industrial piping Part 5: Inspection and testing EN 13480-6:2012, Metallic industrial piping Part 6: Additional requirements for buried piping CEN/TR 13480-7:2002, Metallic industrial piping Part 7: Guidance on
35、 the use of conformity assessment procedures EN 13480-8:2012, Metallic industrial piping Part 8: Additional requirements for aluminium and aluminium alloy piping 3 Terms, definitions, symbols and units 3.1 Terms and definitions For the purposes of this European Standard, the terms and definitions gi
36、ven in EN 764-3:2002 and the following apply. Specific definitions are given in the relevant Parts of this European Standard. 3.1.1 ambient temperature temperature of the surrounding atmosphere in the immediate vicinity of the piping system 3.1.2 piping system piping pipe or system of pipes for the
37、conveyance of fluids within an industrial site Note 1 to entry A piping system can be regarded as one single system provided it conveys substances having the same properties and it is as a whole designed for the same allowable pressure. Note 2 to entry Interruption by different components such as pu
38、mps, machines, vessels etc. does not preclude the integration to one single piping. 3.1.3 fluid gases, liquids and vapours in pure phase as well as mixtures thereof Note to entry A fluid may contain a suspension of solids. 3.1.4 manufacturer person or organization that takes full responsibility for
39、the design and manufacture of the piping system and its conformity to EN 13480 Note 1 to entry The manufacturer is responsible for carrying out all relevant production processes and testing as specified in the applicable standards. BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 7 Note 2 to
40、entry If a manufacturer employs subcontractors or fabricators/installers for certain items he is responsible for their work. Note 3 to entry In the EC Member States a manufacturer or his representative is responsible for the conformance of a piping system he puts on the market, with the essential sa
41、fety requirements of the PED. 3.1.5 piping fabricator and/or installer individual or organization that takes responsibility for the fabrication and/or installation of industrial piping complying with the requirements of EN 13480 Note to entry The piping fabricator or the installer may be the manufac
42、turer 3.1.6 designer individual or organization that takes responsibility for the design of industrial piping complying with the requirements of EN 13480 Note to entry The designer can also be the manufacturer. 3.1.7 category category in which industrial piping is classified Note to entry The catego
43、ry depends on the fluid contained, the maximum allowable pressure PS and nominal size DN and the physical condition of the fluid. 3.1.8 test physical activity (destructive or non-destructive) carried out in accordance with a defined procedure which provides an objective assessment of a characteristi
44、c of a component or system Note to entry See Figure 3.1-1. 3.1.9 testing performance of a test or examination and production of a record of results and evaluation of the results compared to the requirements Note to entry See Figure 3.1-1. 3.1.10 examination assessment carried out to determine or ver
45、ify the acceptability of a component, system or document Note to entry See Figure 3.1-1. 3.1.11 inspection activity carried out by persons independent of production to verify that the results of the testing and examinations conform to specific requirements Note to entry See Figure 3.1-1. 3.1.12 desi
46、gn validation examination of the design documents to verify that the design conforms to EN 13480 BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 8 3.1.13 imperfection discontinuity noted during testing and inspection which needs to be evaluated with respect to the acceptance criteria 3.1.14
47、defect discontinuity that renders the material integrity unacceptable with respect to the acceptance level 3.1.15 repair process of rectifying a defect in either base material or weld Performed independently from production INSPECTION review of testing activities and testing results EVALUATION evalu
48、ation of results Tests Examination generation of reports and records physical activities e.g. NDT, pressure test Reports, e.g. of RT, UT, MT and PT, PWHT-diagrams a a See EN 13480-5:2012, clause 4 Figure 3.1-1 Scheme of inspection and testing activities 3.2 Symbols and units For the purposes of this
49、 European Standard, the symbols and units given Table 3.2-1 and further symbols of EN 764-2 apply. Additional symbols are given in some of the relevant Parts of this European Standard. BS EN 13480-1:2012EN 13480-1:2012 (E) Issue 3 (2014-08) 9 Table 3.2-1 General symbols and units Symbol Description Unit A elongation at rupture % D, d a diameters mm E Modulus of elasticity N/mm (MPa) e minimum required thickness without allowances and tolerances, to withstand pressure, calculated by the appropriate equa
