1、BS EN 1856-1:2009ICS 91.060.40NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDChimneys Requirements for metal chimneysPart 1: System chimney productsThis British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 Apri
2、l 2010 BSI 2010ISBN 978 0 580 60025 8Amendments/corrigenda issued since publicationDate CommentsBS EN 1856-1:2009National forewordThis British Standard is the UK implementation of EN 1856-1:2009. It supersedes BS EN 1856-1:2003 which is withdrawn. BS EN 1856-1:2003 superseded BS 4543-2:1990 and BS 4
3、543-3:1990, and those requirements and recommendationsrelating to chimneys that were removed from BS 715:1993 . BS 715:1993 was amended and republished as BS 715:2005 leaving only requirements relating to flue boxes.The UK participation in its preparation was entrusted by Technical Committee B/506,
4、Chimneys, to its Subcommittee B/506/5, Chimneys and their components having inner linings of metal.A list of organizations represented on this subcommittee can be obtained on request to its secretary.EN 1856-1 is a candidate “harmonized” European standard and fully takes into account the requirement
5、s of the European Commission mandate M/105, Chimneys, flues and specific products, given under the EU Construction Products Directive (89/106/EEC), and intended to lead to CE marking. The date of applicability of EN 1856-1 as a “harmonized“ European standard, i.e. the date after which this standard
6、may be used for CE marking purposes, is subject to an announcement in the Official Journal of the European Communities.EN 1856-1 is the subject of transitional arrangements agreed under the European Commission mandate. The Member States have agreed a nominal transition period for the co-existence of
7、 EN 1856-1 and their corresponding national standard(s). It is intended that this period will comprise a nominal nine month period during which any required changes to national regulations are to be made, followed by a further nominal twelve month period for the implementation of CE marking. At the
8、end of this co-existence period, the national standard(s) will be withdrawn. In the UK there are no corresponding national standards.Clauses NA.1 to NA.5 of National annex NA (informative) identify the specifications previously required in BS 4543-2:1990, BS 4543-3:1990 and BS 715:1993 for chimneys.
9、 Clause NA.5 identifies the chimney test arrangement and fire-stop recommendations, and Clause NA.6 provides recommendations for chimney ridge terminals under wind load. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct app
10、lication.Compliance with a British Standard cannot confer immunity from legal obligations.11BS EN 1856-2:2004 also partially superseded BS 715:1993 EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 1856-1June 2009ICS 91.060.40 Supersedes EN 1856-1:2003 English VersionChimneys - Requirements for meta
11、l chimneys - Part 1: Systemchimney productsConduits de fume - Prescriptions pour les conduits defume mtalliques - Partie 1: Composants de systmes deconduits de fumeAbgasanlagen - Anforderungen an Metall-Abgasanlagen -Teil 1: Bauteile fr System-AbgasanlagenThis European Standard was approved by CEN o
12、n 7 May 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be ob
13、tained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Manage
14、ment Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
15、 Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by a
16、ny means reservedworldwide for CEN national Members.Ref. No. EN 1856-1:2009: EEN 1856-1:2009 (E) 2 Contents Page Foreword 5 Introduction .6 1 Scope 7 2 Normative references 7 3 Terms and definitions .7 4 Manufacturers declaration for type test 13 5 Dimensions and tolerances . 14 6 Performance requir
17、ements 14 6.1 General . 14 6.2 Mechanical resistance and stability 14 6.2.1 Compressive strength 14 6.2.2 Tensile strength 15 6.2.3 Lateral strength . 15 6.3 Resistance to fire (internal to external) 15 6.4 Sootfire resistance 15 6.5 Hygiene, health and environment, gas tightness 15 6.6 Safety in us
18、e 16 6.6.1 Thermal performance at normal operating conditions . 16 6.6.2 Accidental human contact . 16 6.6.3 Thermal resistance . 17 6.6.4 Water vapour diffusion resistance 18 6.6.5 Condensate penetration resistance 18 6.6.6 Rainwater penetration resistance . 18 6.6.7 Flow resistance . 18 6.6.8 Othe
19、r requirements for terminals 18 6.7 Durability . 19 6.7.1 Durability of the flue liner against corrosion . 19 6.7.2 Flue liner material specification 19 6.7.3 Freeze-thaw resistance 20 6.7.4 Flue liner seals. . 20 7 Product information 21 7.1 Manufacturers instructions . 21 7.2 Minimum information t
20、o be included in the manufacturers documentation and instructions . 21 8 Marking 22 8.1 General . 22 8.2 Chimney sections, fittings or terminals . 22 8.3 Chimney plate . 22 8.4 Packaging 23 9 Product designation . 23 10 Evaluation of conformity 23 10.1 General . 23 10.2 Type testing . 24 10.2.1 Init
21、ial type testing . 24 10.2.2 Further type testing 24 10.2.3 Sampling for type testing . 24 BS EN 1856-1:2009EN 1856-1:2009 (E) 3 10.3 Factory production control (FPC) 24 10.3.1 General . 24 10.3.2 Equipment 25 10.3.3 Raw materials and components 26 10.3.4 Product testing and evaluation 26 10.3.5 Non
22、 conforming products 26 Annex A (normative) Corrosion tests 27 A.1 Corrosion test method for products designated V1 27 A.1.1 General . 27 A.1.2 Pass/Fail criteria 27 A.1.3 Sampling. 27 A.1.4 Test methods . 27 A.1.5 Evaluation. 31 A.1.6 Test report 32 A.2 Corrosion test method for products designated
23、 V2 35 A.2.1 General . 35 A.2.2 Pass/Fail criteria 35 A.2.3 Sampling. 35 A.2.4 Test methods . 35 A.2.5 Evaluation. 37 A.2.6 Test report 38 A.3 Corrosion test method for products designated V3 39 A.3.1 General . 39 A.3.2 Pass/Fail criteria 39 A.3.3 Sampling. 40 A.3.4 Test methods . 40 A.3.5 Evaluatio
24、n. 43 A.3.6 Test report 43 Annex B (normative) Choice of size for type test and sampling 46 Annex C (normative) Sampling for factory production control 47 C.1 Incoming material 47 C.1.1 Sampling plans 47 C.1.2 Acceptable quality level (AQL) . 47 C.1.3 Normal, tightened or reduced inspection . 47 C.1
25、.4 Single, double, multiple or sequential sampling 47 C.1.5 Batch quantity 47 C.1.6 The inspection level 47 C.2 In-process inspection . 48 C.2.1 All dimensional aspects 48 C.2.2 Joint leakage tests 48 C.2.3 Insulation weight checks 48 C.2.4 Volume and density checks . 48 C.2.5 Finished goods checks
26、. 48 Annex D (normative) Factory production control 49 D.1 General . 49 D.2 Insulation material . 49 D.3 Metals, including coatings 49 D.4 Supports . 49 D.5 Seals and sealants 49 D.6 Manufacturing checks . 50 D.6.1 Dimensions 50 D.6.2 Other checks 50 Annex ZA (informative) Clauses of this European S
27、tandard addressing the provisions of the EU Construction Products Directive . 51 ZA.1 Scope and relevant characteristics . 51 ZA.2 Procedure(s) for attestation of conformity of metal system chimneys . 53 ZA.2.1 System(s) of attestation of conformity 53 BS EN 1856-1:2009EN 1856-1:2009 (E) 4 ZA.2.2 EC
28、 Declaration of conformity 54 ZA.3 CE marking and labelling . 55 Bibliography . 61 BS EN 1856-1:2009EN 1856-1:2009 (E) 5 Foreword This document (EN 1856-1:2009) has been prepared by Technical Committee CEN/TC 166 “Chimneys”, the secretariat of which is held by UNI. This European Standard shall be gi
29、ven the status of a national standard, either by publication of an identical text or by endorsement, at the latest by December 2009, and conflicting national standards shall be withdrawn at the latest by March 2011. Attention is drawn to the possibility that some of the elements of this document may
30、 be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 1856-1:2003. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association,
31、and supports essential requirements of EC Directive 89/106/EEC. For relationship with EC Directive 89/106/EEC, see informative Annex ZA, which is an integral part of this document. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are
32、bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden
33、, Switzerland and the United Kingdom. BS EN 1856-1:2009EN 1856-1:2009 (E) 6 Introduction This European Standard has been prepared to be a harmonised standard to provide means of conforming to the essential requirements of the Construction Products Directive and associated EFTA regulations. The gener
34、ic word “chimney“, when used in this European Standard, refers to systems with metallic liner used to convey the products of combustion from any appliance to the outside atmosphere, and thus includes all other terms of common use in the trade, such as vents, flues, shafts, exhaust systems, ducts, et
35、c. This European Standard addresses the durability against corrosion by the use of a minimum material specification for the flue liner as well as an interim solution for testing products for durability against corrosion. Three corrosion resistance tests and their requirements have been adopted from
36、existing corrosion testing being undertaken in various member states (see Annex A). This European Standard describes chimney components, from which system chimneys can be assembled as illustrated in Figure 1. BS EN 1856-1:2009EN 1856-1:2009 (E) 7 1 Scope This European Standard specifies the performa
37、nce requirements for single and multi-wall system chimney products with rigid metallic liners (chimney sections, chimney fittings and terminals, including supports) with nominal diameter up to and including 1200 mm, used to convey the products of combustion from appliances to the outside atmosphere.
38、 It also specifies the requirements for marking, manufacturers instructions, product information and evaluation of conformity. Metal liners and metal connecting flue pipes not covered here are included in EN 1856-2:2009. This European Standard does not apply to structurally independent (free standin
39、g or self-supporting) chimneys. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) app
40、lies. EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products Part 3: Chemical composition and form of products EN 1443:2003, Chimneys General requirements EN 1859, Chimneys Metal chimneys Test methods EN 10088-1, Stainless steels Part 1: List of stainless steels E
41、N 13384-1, Chimneys Thermal and fluid dynamic calculation methods Part 1: Chimneys serving one appliance EN 14241-1, Chimneys - Elastomeric seals and elastomeric sealants . Material requirements and test methods - Part 1: Seals in flue liners EN 15287 (all parts), Chimneys Design, installation and c
42、ommissioning of chimneys EN ISO 3651-2, Determination of resistance to intergranular corrosion of stainless steels. Part 2: Ferritic, austenitic and ferritic-austenitic (duplex) stainless steels. Corrosion test in media containing sulfuric acid (ISO 3651-2:1998) ISO 2859-1, Sampling procedures for i
43、nspection by attributes Part 1: Sampling schemes indexed by acceptance quality limit (AQL) for lot-by-lot inspection 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 appliance outlet position where the products of combustion exit from the appl
44、iance (see Figure 1) 3.2 chimney structure consisting of a wall or walls enclosing a flue or flues EN 1443:2003 BS EN 1856-1:2009EN 1856-1:2009 (E) 8 3.2.1 chimney accessory chimney component not conveying products of combustion EN 1443:2003 3.2.2 chimney component any part of a chimney EN 1443:2003
45、 3.3 chimney designation shortened description of a specific chimney type, which clearly distinguishes it from any other types 3.4 chimney fitting chimney component conveying products of combustion except a chimney section (see Figure 1) EN 1443:2003 3.5 chimney section straight chimney component co
46、nveying products of combustion (see Figure 1) EN 1443:2003 3.6 cladding additional non-structural outer wall around a chimney for protection against heat transfer or weathering, or for decorative purposes (see Figure 1) EN 1443:2003 3.7 connecting flue pipe component or components connecting the hea
47、ting appliance outlet and the chimney (see Figure 1) EN 1443:2003 3.8 corrosion load combination of condensate and corrosion resistance classes necessary for the different operating conditions and types of fuel 3.9 custom built chimney chimney that is installed or built on-site using a combination o
48、f compatible chimney components that may be from one or different sources EN 1443:2003 3.10 design load (DL) load which a chimney or its components are designed to be subjected to, under normal operating conditions, when installed as per manufacturers installation instruction BS EN 1856-1:2009EN 185
49、6-1:2009 (E) 9 3.11 dry operating condition condition when a chimney is designed to operate normally with the temperature of the inner surface of the flue liner above the water dew point EN 1443:2003 3.12 enclosure barrier that, when built around a chimney, will give additional safety in case of fire and can provide additional heat transfer resistance (see Figure 1) EN 1443:2003 3.13 external installation part of a chimney, which is located outside the building 3.14 firestops barrier to prevent the spread of fire 3.15 flexible p
