1、BSI Standards PublicationBS EN 1870-19:2013Safety of woodworkingmachines Circular sawingmachinesPart 19: Circular saw benches (with andwithout sliding table) and building site sawsBS EN 1870-19:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1870-19:2013.To
2、gether with BS EN 1870-18:2013, it supersedes BS EN1870-1:2007+A1:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/23, Woodworking machines.A list of organizations represented on this committee can beobtained on request to its secretary.This pub
3、lication does not purport to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 73577 6ICS 79.120.10Compliance with a British Standard cannot confer immunity
4、 fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 November 2013.Amendments issued since publicationDate Text affectedBS EN 1870-19:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1870-19 November 2013 ICS 79.12
5、0.10 Supersedes EN 1870-1:2007+A1:2009English Version Safety of woodworking machines - Circular sawing machines - Part 19: Circular saw benches (with and without sliding table) and building site saws Scurit des machines pour le travail du bois - Machines scies circulaires - Partie 19: Scies circulai
6、res table de menuisier (avec et sans table mobile) et scies de chantier Sicherheit von Holzbearbeitungsmaschinen - Kreissgemaschinen - Teil 19: Tischkreissgemaschinen (mit und ohne Schiebetisch) und Baustellenkreissgemaschinen This European Standard was approved by CEN on 7 September 2013. CEN membe
7、rs are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on applicatio
8、n to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Manageme
9、nt Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, L
10、ithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17
11、, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1870-19:2013 EBS EN 1870-19:2013EN 1870-19:2013 (E) 2 Contents Page Foreword 5 Introduction .7 1 Scope 8 2 Normative references 8 3 Terms and definitions 11 3.1
12、 General . 11 3.2 Definitions . 11 4 List of significant hazards . 17 5 Safety requirements and/or measures . 23 5.1 General . 23 5.2 Controls . 23 5.2.1 Safety and reliability of control systems 23 5.2.2 Position of controls 24 5.2.3 Starting 25 5.2.4 Normal stopping . 26 5.2.5 Emergency stop 27 5.
13、2.6 Speed control for circular saw benches 27 5.2.7 Power operated adjustment of the saw blade(s) and/or fence(s) on circular saw benches . 28 5.2.8 Interlocking of guards, movements and functions . 29 5.2.9 Failure of the power supply . 29 5.2.10 Failure of the control circuits 29 5.3 Protection ag
14、ainst mechanical hazards . 30 5.3.1 Stability 30 5.3.2 Hazard of break up during operation 30 5.3.3 Tool holder and tool design . 31 5.3.4 Braking . 32 5.3.5 Devices to minimize the possibility or the effect of kickback 33 5.3.6 Workpiece supports and guides . 40 5.3.7 Prevention of access to moving
15、 parts 44 5.3.8 Powered workpiece clamping . 57 5.3.9 Safety appliances 57 5.4 Protection against non-mechanical hazards . 61 5.4.1 Fire . 61 5.4.2 Noise 61 BS EN 1870-19:2013EN 1870-19:2013 (E) 3 5.4.3 Emission of chips and dust 63 5.4.4 Electricity 64 5.4.5 Ergonomics and handling 65 5.4.6 Pneumat
16、ics 66 5.4.7 Electromagnetic compatibility . 66 5.4.8 Laser . 66 5.4.9 Static electricity . 66 5.4.10 Errors of fitting 66 5.4.11 Supply disconnection (Isolation) . 67 5.4.12 Maintenance . 67 6 Information for use 67 6.1 General . 67 6.2 Marking . 68 6.2.1 Marking of the machine 68 6.2.2 Marking of
17、riving knives . 69 6.3 Instruction handbook 69 Annex A (normative) Stability test 74 Annex B (normative) Test for rigidity of building site saws . 75 Annex C (normative) Saw spindle dimensional tolerances 76 Annex D (normative) Riving knife mounting strength test . 77 Annex E (normative) Riving knif
18、e lateral stability test 78 Annex F (normative) Minimum dimensions of the machine table, extension table and insert 79 Annex G (normative) Saw blade guard stability test . 81 G.1 General . 81 G.2 Separately from riving knife mounted saw blade guards . 81 G.2.1 Saw blade guards with lead-in . 81 G.2.
19、2 Saw blade guards with in-feed rollers . 82 G.3 Riving knife mounted saw blade guards . 83 Annex H (normative) Impact test method for guards 85 H.1 General . 85 H.2 Test method . 85 H.2.1 Preliminary remarks 85 H.2.2 Testing equipment . 85 H.2.3 Projectile for guards 85 H.2.4 Sampling. 85 H.2.5 Tes
20、t procedure . 85 H.3 Results 86 H.4 Assessment . 86 H.5 Test report 86 H.6 Test equipment for impact test 86 Annex I (normative) Braking tests 88 I.1 Conditions for all tests 88 I.2 Tests . 88 I.2.1 Un-braked run-down time . 88 I.2.2 Braked run-down time . 88 BS EN 1870-19:2013EN 1870-19:2013 (E) 4
21、Annex ZA (informative) Relationship between this European Standard and the Essential Requirements of EU Directive 2006/42/EC . 89 Bibliography . 92 BS EN 1870-19:2013EN 1870-19:2013 (E) 5 Foreword This document (EN 1870-19:2013) has been prepared by Technical Committee CEN/TC 142 “Woodworkng machine
22、s - Safety”, the secretariat of which is held by UNI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2014, and conflicting national standards shall be withdrawn at the latest by May 2014. Att
23、ention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document together with EN 1870-18 supersedes EN 1870-1:2007+A1:2009. The major techn
24、ical changes from the previous edition are the following: a) the exclusion of saw blade guard mounted on wall, ceiling or floor; b) introduction of PL; c) inclusion of a stability test for displaceable machines; d) more precise requirements for braking function; e) more precise requirement on chips
25、and dust extraction connections; f) extension of usable safety appliances; g) more precise requirements to prevent crushing and shearing hazards. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential re
26、quirements of the Machinery Directive. For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document. EN 1870, Safety of woodworking machines Circular sawing machines consists of the following parts: Part 3: Down cutting cross-cut saws and dual purpose d
27、own cutting cross-cut saws/circular saw benches Part 4: Multi-blade rip sawing machines with manual loading and/or unloading Part 5: Circular saw benches/up-cutting cross-cut sawing machines Part 6: Circular sawing machines for firewood and dual purpose circular sawing machines for firewood/circular
28、 saw benches, with manual loading and/or unloading Part 7: Single blade log sawing machines with integrated feed table and manual loading and/or unloading Part 8: Single blade edging circular rip sawing machines with power driven saw unit and manual loading and/or unloading Part 9: Double blade circ
29、ular sawing machines for cross-cutting with integrated feed and with manual loading and/or unloading BS EN 1870-19:2013EN 1870-19:2013 (E) 6 Part 10: Single blade automatic and semi-automatic up-cutting cross-cut sawing machines Part 11: Semi-automatic and automatic horizontal cross-cut sawing machi
30、nes with one saw unit (radial arm saws) Part 12: Pendulum cross-cut sawing machines Part 13: Horizontal beam panel sawing machines Part 14: Vertical panel sawing machines Part 15: Multi-blade cross-cut sawing machines with integrated feed of the workpiece and manual loading and/or unloading Part 16:
31、 Double mitre sawing machines for V-cutting Part 17: Manual horizontal cutting cross-cut sawing machines with one saw unit (manual radial arm saws) Part 18: Dimension saws Part 19: Circular saw benches (with and without sliding table) and building site saws Organizations contributing to the preparat
32、ion of this European Standard include European Committee of Woodworking Machinery Manufacturers Association “EUMABOIS“. The European Standards produced by CEN/TC 142 are particular to woodworking machines and complement the relevant A and B Standards on the subject of general safety (see Introductio
33、n of EN ISO 12100:2010 for a description of A, B and C standards). According to the CEN-CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, E
34、stonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 1870-19:2013EN
35、 1870-19:2013 (E) 7 Introduction This document has been prepared to be a harmonized standard to provide one means of conforming to the essential safety requirements of the Machinery Directive and associated EFTA regulations. This document is a type “C“ standard as defined in EN ISO 12100:2010. The m
36、achinery concerned and the extent to which hazards, hazardous situations and events are covered are indicated in the scope of this document. When provisions of this type C standard are different from those which are stated in type A or B standards, the provisions of this type C standard take precede
37、nce over the provisions of other standards, for machines that have been designed and built according to the provisions of this type C standard. The requirements of this document are directed to manufacturers and their authorized representatives of circular saw benches (with and without sliding table
38、) and building site saws. They are also useful for designers. This document also includes provisions and examples of information to be provided by the manufacturer to the user. Common requirements for tooling are given in EN 847-1:2013. BS EN 1870-19:2013EN 1870-19:2013 (E) 8 1 Scope This European S
39、tandard deals with all significant hazards, hazardous situations and events as listed in Clause 4 which are relevant to stationary and displaceable circular saw benches (with or without sliding table and/or demountable power feed unit) and building site saws, hereinafter referred to as “machines”, d
40、esigned to cut solid wood, chipboard, fibreboard, plywood and also these materials, if they are covered with plastic edging and/or plastic/light alloy laminates, when they are used as intended and under the conditions foreseen by the manufacturer including reasonably foreseeable misuse. Machines whi
41、ch are designed to cut wood-based material may also be used for cutting hardened plastic materials with similar physical characteristics as wood. NOTE 1 For the definition of stationary and displaceable machine see 3.2.9 and 3.2.10. NOTE 2 Circular saw benches are used for ripping, cross cutting, di
42、mensioning and grooving. Building site saws are used for ripping, cross cutting and dimensioning. The requirements of this document apply also to machines designed for grooving with a width not exceeding 20 mm in one pass by using a milling tool. This document does not apply to: a) machines set up o
43、n a bench or a table similar to a bench, which are intended to carry out work in a stationary position, capable of being lifted by one person by hand. The bench can also be an integrated part of the machine if it consists of hinged legs which can be extended down; b) hand held woodworking machines i
44、ncluding any adaptation permitting their use in a different mode, i.e. bench mounting. NOTE 3 Transportable motor-operated electric tools are covered by the requirements of EN 61029-1:2009 together with EN 61029-2-1:2012; a hand-held motor-operated electric tool and a saw bench to form an integrated
45、 whole are covered by EN 60745-1:2009 together with EN 60745-2-5: 2010. For the purpose of this document, building site saws having a tiltable spindle are considered to be circular saw benches. This document is not applicable to circular saw benches (with and without sliding table) and building site
46、 saws which are manufactured before the date of its publication as EN. NOTE 4 Machines covered by this document are listed under 1.1 of Annex IV of the Machinery Directive. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indisp
47、ensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 614-1:2006+A1:2009, Safety of machinery Ergonomic design principles Part 1: Terminology and general principl
48、es EN 847-1:2013, Tools for woodworking Safety requirements Part 1: Milling tools, circular saw blades EN 894-1:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 1: General principles for human interactions with displays and control actua
49、tors EN 894-2:1997+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 2: Displays BS EN 1870-19:2013EN 1870-19:2013 (E) 9 EN 894-3:2000+A1:2008, Safety of machinery Ergonomics requirements for the design of displays and control actuators Part 3: Control actuators EN 1005-1:2001+A1:2008, Safety of machinery Human physical performance Part 1: Terms and definitions EN 1005-2:2003+A1:2008, Safety of machinery Human physical performance Part 2: Manual handlin
