1、BRITISH STANDARDBS EN 4008-015:2007Aerospace series Elements of electrical and optical connection Crimping tool and associated accessories Part 015: Positioner for crimping tool M22520/2-01 Product standardThe European Standard EN 4008-015:2007 has the status of a British StandardICS 49.060g49g50g3g
2、38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 4008-015:2007This British Standard was published under the authority of the Standards Policy and Strate
3、gy Committee on 31 December 2007 BSI 2007ISBN 978 0 580 57220 3National forewordThis British Standard is the UK implementation of EN 4008-015:2007.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Panel ACE
4、/6/-/3, Aerospace Connectors.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard
5、 cannot confer immunity from legal obligations. Amendments issued since publicationAmd. No. Date CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 4008-015November 2007ICS 49.060English VersionAerospace series - Elements of electrical and optical connection- Crimping tool and associated acce
6、ssories - Part 015:Positioner for crimping tool M22520/2-01 - Product standardSrie arospatiale - Organes de connexion lectrique etoptique - Outils de sertissage et accessoires associs -Partie 015: Positionneur pour pince sertir M22520/2-01 -Norme de produitLuft- und Raumfahrt - Elektrische und optis
7、cheVerbinungselemente - Crimpwerkzeug und ZugehrigesZubehr - Teil 015: Positionierer fr Crimzange M22520/2-01 - ProduktnormThis European Standard was approved by CEN on 28 September 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for givi
8、ng this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versio
9、ns (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bul
10、garia, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZ
11、ATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2007 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 4008-015:2007: E2 Contents Page Foreword3 1 Scope 4 2 Normat
12、ive references 4 3 Terms and definitions .4 4 Required characteristics.4 4.1 Description .4 4.2 Dimensions and mass.5 4.3 Material, surface treatment.5 5 Designation 6 6 Marking .6 7 Technical specification .6 EN 4008-015:20073 Foreword This document (EN 4008-015:2007) has been prepared by the Aeros
13、pace and Defence Industries Association of Europe - Standardization (ASD-STAN). After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior
14、 to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2008, and conflicting national standards shall be withdrawn at the latest by May 2008. Attention is drawn to the po
15、ssibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries
16、 are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, S
17、weden, Switzerland and the United Kingdom. EN 4008-015:20074 1 Scope This standard specifies the characteristics for the positioner used with M22520/2-01 crimping tool to crimp electrical contact according to EN 4008-002. 2 Normative references The following referenced documents are indispensable fo
18、r the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100, Aerospace series Elements of electrical and optical connection Test methods Part 100: Gener
19、al. EN 4008-001, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 001: Technical specification. EN 4008-002, Aerospace series Elements of electrical and optical connection Crimping tools and associated accessories Part 002: List of product
20、 standards. MIL-C-22520/2, Crimping tools, terminal, hand, wire termination for wire barrel sizes 20 through 28. 1)3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 2591-100 apply. 4 Required characteristics 4.1 Description Securing the positioner on th
21、e crimping tool is provided by the combined action of the two bayonets and the pressure from the internal spring on the central moving part (locator). The appropriate longitudinal positioning of the contact with respect to the crimping tool indenters is performed by the contact butting against a sho
22、ulder on the central part bore. Locator shall be spring loaded so as to depress 0,79 mm with a force of (9 4,5) N. 1) Published by: Department of Defense (DOD), the Pentagon, Washington D.C.20301 USA. EN 4008-015:20075 4.2 Dimensions and mass Dimensions of positioner are given in Figure 1. Mass: 11
23、g max. Dimensions and tolerances are given in millimetres. General tolerances: 0,25 mm Key 1 Bayonet lock pin 1,09 0,025 2 Locator in extended position 3 Stamp on this surface: “EN4008-015 use with M22520/2-01“ (conform to MIL-C-22250/2) aUse with contact WIRE WK WL WS XY WG XE SEL 2 1 2 1 1 2 EN315
24、5-028 EN3155-029 Figure 1 Positioner 4.3 Material, surface treatment Positioner body: aluminium alloy, color blue Positioner locator: stainless steel Not applicable EN 4008-015:20076 5 Designation EXAMPLE Description Block POSITIONER Identity Block EN4008-015 Number of this standard NOTE If necessar
25、y, the code I9005 shall be placed between the description block and the identity block. 6 Marking See Figure 1. 7 Technical specification See EN 4008-001. EN 4008-015:2007blankBS EN 4008-015:2007BSI389 Chiswick High RoadLondonW4 4ALBSI British Standards InstitutionBSI is the independent national bod
26、y responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest
27、amendments or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can b
28、e found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign stan
29、dards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation
30、 of those that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information s
31、ervices are also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purc
32、hase price of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- informati
33、on about BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extra
34、ct may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbo
35、ls, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
