EN 573-3-2013 en Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3 Chemical composition and form of products《铝和铝合金 锻制品的化学成分和形态 第3部分 产品的化学成.pdf
《EN 573-3-2013 en Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3 Chemical composition and form of products《铝和铝合金 锻制品的化学成分和形态 第3部分 产品的化学成.pdf》由会员分享,可在线阅读,更多相关《EN 573-3-2013 en Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3 Chemical composition and form of products《铝和铝合金 锻制品的化学成分和形态 第3部分 产品的化学成.pdf(40页珍藏版)》请在麦多课文档分享上搜索。
1、BSI Standards PublicationBS EN 573-3:2013Aluminium and aluminiumalloys Chemical compositionand form of wrought productsPart 3: Chemical composition and form ofproductsBS EN 573-3:2013 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 573-3:2013. Itsupersedes BS EN
2、 573-3:2009 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee NFE/35, Light metals and their alloys.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the neces
3、saryprovisions of a contract. Users are responsible for its correctapplication. The British Standards Institution 2013. Published by BSI StandardsLimited 2013ISBN 978 0 580 82399 2ICS 77.120.10; 77.150.10Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Sta
4、ndard was published under the authority of theStandards Policy and Strategy Committee on 31 October 2013.Amendments issued since publicationDate Text affectedBS EN 573-3:2013EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 573-3 October 2013 ICS 77.120.10; 77.150.10 Supersedes EN 573-3:2009Engli
5、sh Version Aluminium and aluminium alloys - Chemical composition and form of wrought products - Part 3: Chemical composition and form of products Aluminium et alliages daluminium - Composition chimique et forme des produits corroys - Partie 3: Composition chimique et forme des produits Aluminium und
6、 Aluminiumlegierungen - Chemische Zusammensetzung und Form von Halbzeug - Teil 3: Chemische Zusammensetzung und Erzeugnisformen This European Standard was approved by CEN on 15 August 2013. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for g
7、iving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three o
8、fficial versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies
9、 of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spai
10、n, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2013 CEN All rights of exploitation in any form and by any means reserved worldwide
11、 for CEN national Members. Ref. No. EN 573-3:2013: EBS EN 573-3:2013EN 573-3:2013 (E) 2 Contents Page Foreword 3 1 Scope 4 2 Normative references 4 3 Chemical composition limits 4 4 Writing rules .4 5 Alloy designations .5 6 Sequence of elements .5 7 Rounding rules for determination of compliance 5
12、Annex A (normative) Form of products . 20 A.1 General . 20 A.2 European Standards . 20 Annex B (normative) Guidelines for the introduction of new wrought aluminium and wrought aluminium alloys in CEN/TC 132 standards . 34 B.1 General principles. 34 B.2 Rules for introduction of new alloys. 34 B.3 Pr
13、ocedure for introduction of new alloys 34 B.4 Addendum for new alloys for future introduction . 34 Bibliography . 35 BS EN 573-3:2013EN 573-3:2013 (E) 3 Foreword This document (EN 573-3:2013) has been prepared by Technical Committee CEN/TC 132 “Aluminium and aluminium alloys”, the secretariat of whi
14、ch is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 2014, and conflicting national standards shall be withdrawn at the latest by April 2014. Attention is drawn to the possib
15、ility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 573-3:2009. CEN/TC 132 affirms its policy that if a patentee refuses to grant licenses on
16、standardized products under reasonable and not discriminatory conditions, this product will be removed from the corresponding document. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 7 “Sheets, strips and plates“ to revise EN 573-3:2009. CEN/TC 132 has decided t
17、o revise this European Standard as follows: addition of the alloy EN AW-4115 in Table 4 and Table A.4; addition of the alloy EN AW-5449A in Table 5 and Table A.5; addition of the alloys EN AW-6026 and EN AW-6064A in Table 6 and Table A.6; correction of a typing error in the chemical symbol of EN AW-
18、6023 in Table A.6. EN 573 comprises the following parts under the general title “Aluminium and aluminium alloys Chemical composition and form of wrought products“: Part 1: Numerical designation system Part 2: Chemical symbol based designation system Part 3: Chemical composition and form of products
19、Part 5: Codification of standardized wrought products According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finla
20、nd, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 573-3:2013EN 573-3:2013 (E)
21、 4 1 Scope This European Standard specifies the chemical composition limits of wrought aluminium and wrought aluminium alloys and form of products. The chemical composition limits of aluminium and aluminium alloys specified herein are completely identical with those registered with the Aluminum Asso
22、ciation, 1525, Wilson Boulevard, Suite 600, Arlington, VA 22209, USA, for the corresponding alloys. Guidelines for the introduction of new wrought aluminium and wrought aluminium alloys in standards are presented in Annex B. 2 Normative references The following documents, in whole or in part, are no
23、rmatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 573-2, Aluminium and aluminium alloys Chemical compositi
24、on and form of wrought products Part 2: Chemical symbol based designation system 3 Chemical composition limits The chemical composition of aluminium and aluminium alloys is specified in percentage by mass in Table 1 to Table 8. Limits of impurities are expressed as a maximum; limits of alloying elem
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- EN57332013ENALUMINIUMANDALUMINIUMALLOYSCHEMICALCOMPOSITIONANDFORMOFWROUGHTPRODUCTSPART3CHEMICALCOMPOSITIONANDFORMOFPRODUCTS

链接地址:http://www.mydoc123.com/p-712402.html