1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS EN 840-2:2012Mobile waste and r e c y c l i n g c o n t a i n e r sPart 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb li
2、fting devices Dimensions and designBS EN 840-2:2012 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 840-2:2012. It supersedes BS EN 840-2:2004, which is withdrawn.The UK participation in its preparation was entrusted to T e c h n i c a l C o m m i t t e e B / 5
3、0 8 / 1 , W a s t e c o n t a i n e r s a n d a s s o c i a t e d lifting devices on refuse collection vehicles.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. U
4、sers are responsible for its correct application. The British Standards Institution 2012. Published by BSI Standards Limited 2012.ISBN 978 0 580 72433 6 ICS 13.030.40 Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authori
5、ty of the Standards Policy and Strategy Committee on 31 December 2012.Amendments issued since publicationDate T e x t a f f e c t e dBS EN 840-2:2012EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 840-2 December 2012 ICS 13.030.40 Supersedes EN 840-2:2004English Version Mobile waste and recycli
6、ng containers - Part 2: Containers with 4 wheels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices - Dimensions and design Conteneurs roulants ordures mnagres et recyclables - Partie 3: Conteneurs 4 roues de capacit infrieure ou gale 1300 l couvercle(s) bomb(s)
7、, pour lve-conteneurs par tourillon et/ou peigne - Dimensions et conception Fahrbare Abfall- und Wertstoffbehlter - Teil 2: Behlter mit 4 Rdern und einem Nennvolumen bis 1300 l mit Flachdeckel(n), fr Schttungen mit Zapfenaufnahme und/oder fr Kammschttungen - Mae und Formgebung This European Standard
8、 was approved by CEN on 22 September 2012. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning s
9、uch national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its o
10、wn language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany,
11、 Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NOR
12、MUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2012 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 840-2:2012: EBS EN 840-2:2012EN 840-2:2012 (E) 2 Contents Page Foreword 31 Scope 42 Normative references 43 Terms and de
13、finitions .44 Volumes 55 Dimensions and design 56 Nominal mass .67 Safety and health requirements .68 Testing 69 Marking .610 Designation 7Annex A (informative) Recommendations for manufacturers of lifting devices . 15Annex B (informative) A-Deviations . 17Bibliography . 18BS EN 840-2:2012EN 840-2:2
14、012 (E) 3 Foreword This document (EN 840-2:2012) has been prepared by Technical Committee CEN/TC 183 “Waste management”, the secretariat of which is held by DIN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at
15、the latest by June 2013, and conflicting national standards shall be withdrawn at the latest by June 2013. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all
16、 such patent rights. This document supersedes EN 840-2:2004. Technical changes since the latest edition: The content was adapted to the current state of the art and revised editorially. Figure 3 has been deleted. Frontal receivers Form B and C have been deleted. Figure 2 has been changed accordingly
17、. This European Standard is one part of the series of standards of EN 840 with the main title Mobile waste and recycling containers comprising the following parts: Part 1: Containers with 2 wheels with a capacity up to 400 l for comb lifting devices Dimensions and design; Part 2: Containers with 4 w
18、heels with a capacity up to 1 300 l with flat lid(s), for trunnion and/or comb lifting devices Dimensions and design (the present document); Part 3: Containers with 4 wheels with a capacity up to 1 300 l with dome lid(s), for trunnion and/or comb lifting devices Dimensions and design; Part 4: Contai
19、ners with 4 wheels with a capacity up to 1 700 l with flat lid(s), for wide trunnion or BG- and/or wide comb lifting devices Dimensions and design; Part 5: Performance requirements and test methods; Part 6: Safety and health requirements. According to the CEN/CENELEC Internal Regulations, the nation
20、al standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithu
21、ania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. BS EN 840-2:2012EN 840-2:2012 (E) 4 1 Scope This European Standard specifies dimensions and design requirements of mobile waste containers with 4 wh
22、eels, with flat lid(s) and capacity up to 1 300 l to be used by trunnion and/or comb lifting device. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cite
23、d applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 840-5, Mobile waste and recycling containers Part 5: Performance requirements and test methods EN 840-6:2012, Mobile waste and recycling containers Part 6: Safety and health requir
24、ements EN 1501-1, Refuse collection vehicles General requirements and safety requirements Part 1: Rear loaded refuse collection vehicles EN 1501-5:2011, Refuse collection vehicles General requirements and safety requirements Part 5: Lifting devices for refuse collection vehicles EN ISO 11469, Plasti
25、cs Generic identification and marking of plastics products (ISO 11469) 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. NOTE Terms for components of mobile waste containers and lifting devices in three languages are given in Annex A of EN 840-1:20
26、12. 3.1 mobile waste and recycling container appropriately designed container fitted with wheels intended to temporarily store waste 3.2 lifting device structure which picks-up, tilts and empties containers 3.3 comb lifting device lifting device in which the picking-up system consists of a row of te
27、eth and a locking system to retain the container during emptying 3.4 trunnion lifting device lifting device in which the picking-up system consists of a pair of arms with automatic locking mechanism to fit the trunnion to retain the container during emptying 3.5 volume total space inside the contain
28、er when the lid is closed Note 1 to entry: See Table 1. BS EN 840-2:2012EN 840-2:2012 (E) 5 3.6 nominal volume capacity volume stated by the manufacturer Note 1 to entry: See Table 1 without tolerances. Note 2 to entry: The English term “capacity“ and the French term “capacit“ are translated in the
29、German version by the term “Nennvolumen“. 3.7 nominal mass mass, which is calculated as given in Clause 6 3.8 total permissible mass mass of the container plus the nominal mass 3.9 functional and safety dimensions essential dimensions which ensure the functionality and interchangeability of the cont
30、ainer with the compatible lifting device and which are necessary for the operators safety and health 4 Volumes This part of EN 840 identifies the two classes of containers: Class I - small size (nominal volume up to 1 000 l); Class II - large size (nominal volume between 1 000 l and 1 300 l). Within
31、 the two above-mentioned classes of containers the following volumes are identified: 500 l, 660 l, 770 l, 1 000 l, 1 100 l and 1 200 l. Nominal volumes different from those referenced can be used by agreement between user and manufacturer. The tolerance of the volumes shall be 5 % maximum measured a
32、ccording to EN 840-5. 5 Dimensions and design 5.1 The design of the containers need not correspond to the drawings given in Figure 1. The functional dimensions given in Table 1 shall be respected. Recommendations for manufacturers of lifting devices are given in Annex A (see also EN 1501-1). 5.2 The
33、 container shall be constructed so that when it is unloaded or loaded with a nominal load (see Clause 6), it fits on an approved compatible lifting device. It shall be automatically locked safely into the lifting device during the lifting operation. If the container is equipped with a comb receiver,
34、 it shall correspond to Figure 2. 5.3 The lid(s) shall cover the opening of the container completely. It shall be opened easily by itself during the emptying cycle it/they shall be made with at least two fixing points and have at least one means of opening. 5.4 Handles fitted in front of the trunnio
35、n shall have a measurement over the handles of 10 mm less than the actual measurement in Table 1, dimension N 33. The handles and their location also shall be designed so that they do not damage the operator. 5.5 If the container has ribs in the frontal receiver they shall meet the requirements of F
36、igures 2 and 4. BS EN 840-2:2012EN 840-2:2012 (E) 6 5.6 The container shall have four swivel castors. Each swivel castor shall be capable of withstanding 1/3 of the total permissible mass. Each castor shall meet the requirements of EN 840-5. The container shall have facilities for mounting the casto
37、r platine according to at least one of the measurements as shown in Figure 5. 5.7 All the surfaces of the container including design features shall be smooth and free of any foreign bodies or flaws. 5.8 The container should have a drain plug. 5.9 When direction locks are fitted they shall be fixed o
38、n at least two castors. 5.10 The container should be fitted with two braked wheels to requirements of EN 840-5. In case of centralised braking and locking system the brake pedal and the lock shall be fixed on a lateral side of the container. The centralised locking shall be able to be unlocked with
39、a standard triangular key as shown in Figure 6. The effectiveness of the centralised braking system shall conform to EN 840-5. 6 Nominal mass The container shall be constructed strongly enough to carry a mass of 0,4 kg/dm3 x nominal volume. Containers with a nominal volume of more than 1 100 l shall
40、 be constructed strongly enough to carry a load of 440 kg. 7 Safety and health requirements The container shall meet the safety and health requirements according to EN 840-6. 8 Testing The container shall fulfil the performance requirements and the tests of EN 840-5. 9 Marking 9.1 Each container com
41、plying with the requirements of this part of EN 840 shall be durably and readably marked on the body in a visible part with: number of this European Standard (EN 840-2); nominal volume; manufacturers name or trademark; total permissible mass, in kilograms; year and month of manufacturing. 9.2 Additi
42、onal marking for quality, recycling, etc. is allowed. Starting five years after the publication of this standard, plastic parts of containers, lids and wheels shall be marked in accordance with EN ISO 11469. The use of recycled materials is allowed, presuming that all requirements of this standard a
43、re complied with. BS EN 840-2:2012EN 840-2:2012 (E) 7 10 Designation The container complying with the requirements of this European Standard shall be designated as follows: Container EN 840-2 660 A O 264 Description Standard number Nominal volume, in litres Frontal receiver form: A = frontal receive
44、r 0 = without frontal receiver Lateral receiver: A = trunnions 0 = without lateral receiver Nominal load, in kilograms BS EN 840-2:2012EN 840-2:2012 (E) 8 Table 1 Dimensions Dimensions in millimetres Dimen-sion N Class I - Small sizes 1 000 l Remarks 500 l 660 l 770 l 1 000 l 1 100 l 1 200 l 1a1 370
45、 10 1 370 10 1 370 10 1 370 10 1 370 10 1 370 10 In case of trunnions 2 680 max. 780 max. 800 max. 1 115 max. 1 115 max. 1 115 max. Total width lid(s) closed 3 740 max. 850 max. 870 max. 1 190 max. 1 190 max. 1 190 max. When lid open 4 1 370 max 1 370 max. 1 370 max. 1 470 max. 1 470 max. 1 470 max.
46、 5a860 min.; 1 290 max. 860 min.; 1 290 max. 860 min.; 1 290 max. 860 min.; 1 290 max. 860 min.; 1 290 max. 860 min.; 1 290 max. Tipping edge 6 480 50 585 50 585 50 870 50 885 50 885 50 7a135 min.; 280 max. 135 min.; 280 max. 135 min.; 280 max. 135 min.; 280 max. 135 min.; 280 max. 135 min.; 280 max
47、. In case of trunnions and min 850 from ground 8a700 to 850 700 to 850 700 to 850 700 to 850 700 to 850 700 to 850 Handle position if present 9 600 to 850 600 to 850 600 to 850 600 to 850 600 to 850 600 to 850 Lock position if present 10a0454606545460+6545460+1540500+1540500+1540500+In case of trunn
48、ions 11a 200 2 *) 200 2 *) 200 2 *) 200 2 *) 200 2 *) 200 2 *)*) min 160 optional according to 5.3 of EN 840-6:2012 12a19 min. 19 min. 19 min. 19 min. 19 min. 19 min. In case of frontal receiver 13a13 5+313 5+313 5+313 5+313 5+313 5+3In case of frontal receiver 14a2221+2221+2221+2221+2221+2221+In case of frontal receiver 15 - - - - - - This dimension is used no longer. 16a26 1 26 1 26 1 26 1 26 1 26 1 In case of frontal receiver 17a58 max. 58 max. 58 max. 58 max. 58 max. 58 max. In case of frontal receiver 18a20 min. 20 min. 20 min. 20 min. 20 min. 20 min. In case of frontal receiver 19 1
