1、BRITISH STANDARDBS EN 15330-2:2008Surfaces for sports areas Synthetic turf and needle-punched surfaces primarily designed for outdoor use Part 2: Specification for needle-punched surfacesICS 97.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40
2、g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 15330-2:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 February 2008 BSI 2008ISBN 978 0 580 57571 6National forewordThis British
3、 Standard is the UK implementation of EN 15330-2:2008. It partially supersedes BS 7044-4:1991. EN 15330-2:2008 is one of a package of standards being produced by CEN/TC 217. On publication of the entire package, BS 7044 will be withdrawn.The UK participation in its preparation was entrusted to Techn
4、ical Committee PRI/57, Surfaces for sports areas.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance wit
5、h a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda issued since publicationDate CommentsEUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 15330-2January 2008ICS 97.220.10English VersionSurfaces for sports areas - Synthetic turf and needle-punchedsurfaces primari
6、ly designed for outdoor use - Part 2:Specification for needle-punched surfacesSols sportifs - Surfaces en gazon synthtique et en textileaiguillet principalement destines lusage en extrieur -Partie 2 : Spcifications relatives aux surfaces en textileaiguilletSportbden - berwiegend fr den Auenbereichhe
7、rgestellte Kunststoffrasenflchen und Nadelfilze - Teil 2:Festlegungen fr NadelfilzeThis European Standard was approved by CEN on 22 December 2007.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a
8、national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version i
9、n any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, E
10、stonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPI
11、SCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2008 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15330-2:2008: EEN 15330-2:2008 (E) 2 Contents Page Foreword3 1 Scope 4 2 Normative references 4 3 Ter
12、ms and definitions .5 4 General6 4.1 Resistance to artificial weathering.6 4.2 Water permeability.6 4.3 Joint strength.6 4.4 Abrasion resistance 6 4.5 Tensile properties of carpet6 5 Surfaces designed for multi-sports use6 5.1 General6 5.2 Vertical ball rebound .7 5.3 Ball roll and velocity change 7
13、 5.4 Shock absorption.7 5.5 Rotational Resistance .8 5.6 Angled ball behaviour .8 6 Surfaces designed primarily for tennis .8 6.1 General8 6.2 Vertical ball rebound .8 6.3 Angled ball behaviour .8 6.4 Shock absorption.8 6.5 Rotational resistance 8 7 Information to be provided by the manufacturer or
14、supplier9 Annex A (informative) Site tests 10 A.1 General10 A.2 Multi-sports pitches.11 A.3 Tennis courts .12 Annex B (normative) Preparation of wet test pieces.13 Annex C (informative) Ball rebound 14 Annex D (normative) Information to be supplied by the manufacturer or supplier regarding maintenan
15、ce .15 Annex E (normative) Product identification .16 Annex F (normative) Surface regularity17 EN 15330-2:2008 (E) 3 Foreword This document (EN 15330-2:2008) has been prepared by Technical Committee CEN/TC 217 “Surfaces for sports areas”, the secretariat of which is held by BSI. This European Standa
16、rd shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2008, and conflicting national standards shall be withdrawn at the latest by July 2008. Attention is drawn to the possibility that some of the elements of this doc
17、ument may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. EN 15330 consists of the following parts, under the general title Surfaces for sports areas Synthetic turf and needle-punched surfaces primarily designed for out
18、door use: Part 1: Specification for synthetic turf Part 2: Specification for needle-punched surfaces According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, C
19、zech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 15330-2:2008 (E) 4 1 Scope This Europea
20、n Standard specifies performance and durability characteristics of needle-punched sports surfaces primarily used outdoors. Two categories of surfaces are covered, based on the principal sporting use of the surface, as follows: surfaces designed for multi-sports use; and surfaces designed primarily f
21、or tennis. The requirements are intended to apply to surfaces used for community, educational and recreational sport. For professional and elite levels of competition, many sports governing bodies have published their own specifications; the requirements of the sports governing bodies might differ f
22、rom those detailed in this European Standard and facility developers are advised to ensure that they select surfaces offering the correct levels of performance for the levels of competition to be played on the pitch or court. This European Standard is based on type approval testing of products in th
23、e laboratory. Selected requirements may also be used on-site to assess the suitability of installed surfaces. Guidance on the testing of installations is given in Annex A. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated refe
24、rences, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 430, Resilient floor coverings Determination of mass per unit area EN 933-1, Tests for geometrical properties of aggregates Part 1: Determination of pa
25、rticle size distribution Sieving method EN 1097-3, Tests for mechanical and physical properties of aggregates - Part 3: Determination of loose bulk density and voids EN 1969, Surfaces for sports areas Determination of thickness of synthetic sports surfaces EN 12616, Surfaces for sports areas Determi
26、nation of water infiltration rate EN 12230, Surfaces for sports areas Determination of tensile properties of synthetic sports surfaces EN 12235, Surfaces for sports areas Determination of vertical ball behaviour EN 12228, Surfaces for sports areas Determination of joint strength of synthetic surface
27、s EN 12229, Surfaces for sports areas Procedure for the preparation of synthetic turf and needle-punch test pieces EN 12234, Surfaces for sports areas Determination of ball roll behaviour EN 13036-7, Road and airfield surface characteristics Test methods Part 7: Irregularity measurement of pavement
28、courses: the straightedge test EN 13672, Surfaces for sports areas Determination of resistance to abrasion of non-filled synthetic turf EN 13744, Surfaces for sports areas Procedure for accelerated ageing by immersion in hot water EN 15330-2:2008 (E) 5 EN 13865, Surfaces for sports areas Determinati
29、on of angled ball behaviour Tennis EN 14808, Surfaces for sports areas Determination of shock absorption EN 14809, Surfaces for sports areas Determination of vertical deformation EN 14836, Synthetic surfaces for outdoor sports areas - Exposure to artificial weathering EN 14955, Surfaces for sports a
30、reas Determination of composition and particle shape of unbound mineral surfaces for outdoor sports areas EN 15301-1, Surfaces for sports areas Part 1: Determination of rotational resistance EN 20105-A02, Textiles Tests for colour fastness Part A02: Grey scale for assessing change in colour (ISO 105
31、-A02:1993) EN ISO 5079, Textiles Fibres - Determination of breaking force and elongation at break of individual fibres (ISO 5079:1995) EN ISO 13934-1, Textiles Tensile properties of fabrics Part 1: Determination of maximum force and elongation at maximum force using the strip method (ISO 13934-1:199
32、9) ISO 1766, Textile floor coverings Determination of thickness of pile above the substrate ISO 8543, Textile floor coverings Methods for determination of mass ISO 11357-3, Plastics Differential scanning calorimetry (DSC) Part 3: Determination of temperature and enthalpy of melting and crystallizati
33、on 3 Terms and definitions For the purposes of this document, the following terms and definitions apply. 3.1 non-filled needle-punched surface needle-punched or fibre bonded surface that does not contain any form of unbound particulate fill within the pile of the carpet 3.2 filled needle-punched sur
34、face needle-punched or fibre bonded surface whose pile is either totally filled or partly filled with an unbound particulate material (typically sand) 3.3 surface for multi-sports needle-punched or fibre bonded surface designed to be used for more than one sport EN 15330-2:2008 (E) 6 4 General 4.1 R
35、esistance to artificial weathering 4.1.1 Colour fastness When tested in accordance with EN 20105-A02 following artificial weathering in accordance with EN 14836, the change in colour of the weathered needle-punched surface compared to an unaged test specimen of the needle-punched surface shall be Gr
36、ey Scale 4 or greater. 4.1.2 Tensile strength When tested in accordance with EN ISO 5079, but at a laboratory temperature of (23 2) C following artificial weathering in accordance with EN 14836, the tensile strength of the fibres used to form the pile of the needle-punched surface shall be within 50
37、 % of the tensile strength of the unaged yarn fibres. 4.2 Water permeability When tested in accordance with EN 12616, the water infiltration rate of surfaces designed to be permeable shall be equal to or greater than 180 mm/h. 4.3 Joint strength When tested in accordance with Method 2 of EN 12228, f
38、ollowing immersion in hot water in accordance with EN 13744, the strength of bonded joints shall be equal to or greater than 25 N/100 mm. 4.4 Abrasion resistance 4.4.1 Non-filled surfaces When tested in accordance with EN 13672, the percentage mass loss after 2 000 cycles shall be equal to or less t
39、han 2 %. 4.4.2 Filled surfaces When tested in accordance with EN 13672, but modified so that each wheel is acting under a load of 250 g, the percentage mass loss after 2 000 cycles shall be equal to or less than 2 %. 4.5 Tensile properties of carpet When tested in accordance with EN ISO 13934-1, the
40、 maximum force shall be greater than 7,5 N/mm. 5 Surfaces designed for multi-sports use 5.1 General Needle-punched surfaces designed for multi-sports use shall conform to the requirements given in clause 4 and those in 5.2 to 5.6. Test pieces shall be prepared in accordance with EN 12229 and with th
41、e manufacturers instructions prior to testing. Wet test pieces shall be prepared in accordance with the procedure given in Annex B. EN 15330-2:2008 (E) 7 5.2 Vertical ball rebound NOTE See also Annex C. 5.2.1 General The surface shall conform to the requirements given in 5.2.2, 5.2.3 or 5.2.4, as ap
42、propriate, depending on the sports to be played on the surface. 5.2.2 Football When tested in accordance with EN 12235 using a football under both dry and wet conditions, the vertical ball rebound shall be between 45 % and 85 %. 5.2.3 Hockey When tested in accordance with EN 12235 using a hockey bal
43、l under both dry and wet conditions, the vertical ball rebound shall be less than 90 %. 5.2.4 Tennis When tested in accordance with EN 12235 using a tennis ball under both dry and wet conditions, the vertical ball rebound shall be greater than 80 %. 5.3 Ball roll and velocity change When tested in a
44、ccordance with EN 12234 using a hockey ball under both dry and wet conditions, the ball roll shall be between 5,0 m and 15,0 m. When tested in accordance with EN 12234 using a football under both dry and wet conditions, the velocity change shall be between 0,10 m/s and 0,75 m/s. 5.4 Shock absorption
45、 When tested in accordance with EN 14809 under both dry and wet conditions, the shock absorption shall be classified as in Table 1. Table 1 Classification of shock absorption for multi-sports surfaces Force reduction (%) Classification 45 SANP 4 NOTE 1 If tennis is to be played, the shock absorption
46、 should typically be Class SANP 1. NOTE 2 For general sports training (non-contact) and physical education, the shock absorption should typically be Class SANP 2 or SANP 3. NOTE 3 If hockey is the priority sport or general sports training (contact) is to be undertaken, the shock absorption should ty
47、pically be Class SANP 3 or SANP 4. NOTE 4 If football is to be played, the shock absorption should typically be Class SANP 4. EN 15330-2:2008 (E) 8 5.5 Rotational Resistance When tested in accordance with EN 15301-1, using the dimpled rubber test foot under both dry and wet conditions, the rotationa
48、l resistance shall be between 25 Nm and 50 Nm. 5.6 Angled ball behaviour The angled ball behaviour of multi-sports surfaces designed for tennis shall conform to 6.3. 6 Surfaces designed primarily for tennis 6.1 General Needle-punched surfaces designed primarily for tennis shall conform to the requir
49、ements given in clause 4 and those in 6.2 to 6.5. Test pieces shall be prepared in accordance with EN 12229 and the instructions of the manufacturer prior to testing. Wet test pieces shall be prepared in accordance with the procedure given in Annex B. 6.2 Vertical ball rebound NOTE See also Annex C. When tested in accordance with EN 12235 using a tennis ball under both dry and wet conditions, the vertical ball rebound shall be greater than 80 %. 6.3 Angled ball behaviour When tested in acc
