1、BRITISH STANDARDBS EN 60335-2-36: 2002+A11:2012Incorporating corrigendum August 2007Household and similar electrical appliances Safety Part 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elementsICS 97.040.20g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56
2、g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58National forewordThis British Standard is the UK implementation of EN 60335-2-36:2002+A11:2012, incorporating corrigendum August 2007. It is derived
3、from IEC 60335-2-36:2002, incorporating amendment 2:2008. It supersedes BS EN 60335-2-36:2002+A2:2008 which will be withdrawn on 21 December 2014.The start and finish of text introduced or altered by amendment is indicated in the text by tags. Tags indicating changes to IEC text carry the number of
4、the IEC amendment. For example, text altered by IEC amendment 1 is indicated by !“.Where a common modification has been introduced by amendment, the tags carry the number of the amendment. For example, the common modifications introduced by CENELEC amendment A11:2012 are indicated by hi.The UK parti
5、cipation in its preparation was entrusted by Technical Committee CPL/61, Safety of household and similar electrical appliances, to Subcommittee CPL/61/5, Commercial catering equipment.A list of organizations represented on this subcommittee can be obtained on request to its secretary.This publicatio
6、n does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.BS EN 60335-2-36:2002+A11:2012This British Standard waspublished under the authorityof the Stan
7、dards Policy andStrategy Committeeon 29 January 2003 The British Standards Institution 2012. Published by BSI Standards Limited 2012.Amendments/corrigenda issued since publicationAmd. No. Date Comments 15430 11 November 2004 Implementation of IEC amendment 1:2004 with CENELEC endorsement A1:20041746
8、5Corrigendum No. 130 November 2007 Implementation of CENELEC corrigendum August 2007. Last paragraph of EN foreword replaced. Addition to Annex ZB deleted30 September 2008 Implementation of IEC amendment 2:2008 with CENELEC endorsement A2:200831 May 2012 Implementation of CENELEC amendment A11:2012I
9、SBN 978 0 580 75902 4EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMICS 97.040.20English versionHousehold and similar electrical appliances SafetyPart 2-36: Particular requirements for commercial electric cooking ranges, ovens, hobs and hob elements Appareils lectrodomestiques et analogues ScuritPar
10、tie 2-36: Rgles particulires pour les cuisinires, les fours, les tables de cuisson et les foyers de cuisson lectriques usage collectifSicherheit elektrischer Gerte fr denHausgebrauch und hnliche ZwecheTeil 2-36: Besondere Andforderungen frelektrische Herde, Brat-und Backfen und Kochplatten fr den ge
11、werblichen GebrauchUp-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to anyCENELEC member.This European Standard exists in three official versions (English, French,German). A version in any other language ma
12、de by translation under theresponsibility of a CENELEC member into its own language and notified to theCentral Secretariat has the same status as the official versions.CENELEC members are the national electrotechnical committees of Austria,Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland,
13、France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.CENELECEuropean Committee for Electrotechnical StandardizationComit Europen de Normalisation Electrot
14、echniqueEuropisches Komitee fr Elektrotechnische NormungCentral Secretariat: rue de Stassart 35, B-1050 Brussels 2002 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.Ref. No. EN 60335-2-36:2002 EIncorporating corrigendum August 2007(IEC 60335-2-
15、36:2002)(CEI 60335-2-36:2002) (IEC 60335-2-36:2002)EN 60335-2-36:2002+A11April 2012This European Standard was approved by CENELEC on 2002-12-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Regulations national standard without any alteration.which stipulate the conditions for g
16、iving this European Standard the status of aForeword The text of document 61E/398/FDIS, future fifth edition of IEC 60335-2-36, prepared by SC 61E of the IEC Technical Committee 61, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as EN 60335-2-36 on 2002-12-01. This Europe
17、an Standard replaces EN 60335-2-36:2000. The following dates are applicable: - latest date by which the EN has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2003-09-01 - date on which national standards conflicting with the EN have to be
18、 withdrawn (dow) 2005-12-01 This part 2 has to be used in conjunction with EN 60335-1, Household and similar electrical appliances Safety Part 1: General requirements. It was established on the basis of the 2002 edition of that standard. Amendments and revisions of Part 1 have also to be taken into
19、account and the dates when such changes become applicable will be stated in the relevant amendment or revision of Part 1. This part 2 supplements or modifies the corresponding clauses of EN 60335-1, so as to convert it into the European Standard: Safety requirements for commercial electric cooking r
20、anges, ovens, hobs and hob elements. When a particular subclause of Part 1 is not mentioned in this part 2, that subclause applies as far as is reasonable. When this standard states “addition“, “modification“ or “replacement“, the relevant text of Part 1 is to be adapted accordingly. NOTE 1 The foll
21、owing numbering system is used: - subclauses, tables and figures that are numbered starting from 101 are additional to those in Part 1; - unless notes are in a new subclause or involve notes in Part 1, they are numbered starting from 101, including those in a replaced clause or subclause; - addition
22、al annexes are lettered AA, BB, etc.; - subclauses, notes and annexes that are additional to those in the IEC standard are prefixed with the letter Z. NOTE 2 The following print types are used: - requirements: in roman type; - test specifications: in italic type; - notes: in small roman type. Words
23、in bold in the text are defined in Clause 3. When a definition concerns an adjective, the adjective and the associated noun are also in bold. There are no special national conditions causing a deviation from this European Standard, other than those listed in Annex ZA to EN 60335-1. _ There are no na
24、tional deviations from this European Standard, other than those listed in Annex ZB toEN 60335-1.BS EN 60335-2-36:2002+A11:2012 EN 60335-2-36:2002+A11:2012 (E)Page 2Introduction _ Endorsement notice The text of the International Standard IEC 60335-2-36:2002 was approved by CENELEC as a European Stand
25、ard without any modification. ABZ xenn (ifnroitamv)e A-vedisnoita :noitiddA sualCe veDiitaon 51.7 uAstria (Ekeltrsocztuhvrero- 5991 gnund GBrN .lB)51.7 ,5991/607 . fI m ehtrakfo gni fixcnailppa dese si siv tonifa elbret cnailppa ehtsah e sni neebt,della eht retnavel fniorms noitasla llaho cni eblsni
26、 eht ni dedutructsnoi for sulanoitidda na no dna e w lebalcihc hf eb naixraen de cnailppa ehtfa eret snit.noitalla _ Foreword to amendment A1 The text of document 61E/435/FDIS, future amendment 1 to IEC 60335-2-36:2002, prepared by SC 61E of the IEC Technical Committee 61, Safety of household and si
27、milar electrical appliances, was submitted to the IEC-CENELEC parallel vote and was approved by CENELEC as amendment A1 to EN 60335-2-36:2002 on 2004-07-01. The following dates are applicable: - latest date by which the amendment has to be implemented at national level by publication of an identical
28、 national standard or by endorsement (dop) 2005-04-01 - date on which national standards conflicting with the amendment have to be withdrawn (dow) 2007-07-01 This amendment supplements or modifies the corresponding clauses of EN 60335-2-36:2002. There are no special national conditions causing a dev
29、iation from this amendment. There are no national deviations from this amendment. _ Endorsement notice The text of amendment 1:2004 to the International Standard IEC 60335-2-36:2002 was approved by CENELEC as an amendment to the European Standard without any modification. _ BS EN 60335-2-36:2002+A11
30、:2012 EN 60335-2-36:2002+A11:2012 (E)Page 3The principle objectives of Low Voltage Directive, 2006/95/EC, are covered in this standard. The essential safety requirements of the Machinery Directive 2006/42/EC have also been taken into account for appliances covered by this part. hiForeword to amendme
31、nt A2 The text of document 61E/594/FDIS, future amendment 2 to IEC 60335-2-36:2002, prepared by SC 61E, Safety of electrical commercial catering equipment, of IEC Technical Committee 61, Safety of household and similar electrical appliances, was submitted to the IEC-CENELEC parallel vote and was app
32、roved by CENELEC as amendment A2 to EN 60335-2-36:2002 on 2008-03-01. The following dates are applicable: - latest date by which the amendment has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2008-12-01 - date on which national standard
33、s conflicting with the amendment have to be withdrawn (dow) 2011-03-01 This amendment supplements or modifies the corresponding clauses of EN 60335-2-36:2002. There are no special national conditions causing a deviation from this amendment. There are no national deviations from this amendment. _ End
34、orsement notice The text of amendment 2:2008 to the International Standard IEC 60335-2-36:2002 was approved by CENELEC as an amendment to the European Standard without any modification. _ In the Bibliography, add the following note to the standard mentioned: ISO 13732-1 NOTE Harmonized as EN ISO 137
35、32-1:2006 (not modified). Foreword to amendment A11This document (EN 60335-2-36:2002/A11:2012) has been prepared by CLC/TC 61, “Safety of household and similar electrical appliances“. The following dates are fixed: latest date by which the amendment has to be implementedat national level by publicat
36、ion of an identical national standard or by endorsement (dop) 2012-12-21 latest date by which the national standards conflicting with the amendment have to be withdrawn (dow) 2014-12-21 This amendment supplements or modifies the corresponding clauses of EN 60335-1:2012, EN 60335-2-36:2002, EN 60335-
37、2-36:2002/A1:2004 and EN 60335-2-36:2002/A2:2008. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. This document has been prepared unde
38、r a mandate given to CENELEC by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive(s). For the relationship with EU Directive(s) see informative Annex ZZ, which is an integral part of this document. _ BS EN 60335-2-36:2002+A11:2012 EN
39、 60335-2-36:2002+A11:2012 (E)Page 4CONTENTSINTRODUCTION6 1 Scope.7 2 Normative references 7 3 Definitions 7 4 General requirement 10 5 General conditions for the tests.10 6 Classification10 7 Marking and instructions10 8 Protection against access to live parts 14 9 Starting of motor-operated applian
40、ces 14 10 Power input and current.15 11 Heating.16 12 Void17 13 Leakage current and electric strength at operating temperature.17 14 Transient overvoltages 17 15 Moisture resistance18 16 Leakage current and electric strength .19 17 Overload protection of transformers and associated circuits 20 18 En
41、durance20 19 Abnormal operation .21 20 Stability and mechanical hazards 22 21 Mechanical strength.23 22 Construction.24 23 Internal wiring.26 24 Components.26 25 Supply connection and external flexible cords 26 26 Terminals for external conductors .27 27 Provision for earthing.27 28 Screws and conne
42、ctions27 29 Clearances, creepage distances and solid insulation28 30 Resistance to heat and fire28 31 Resistance to rusting .28 32 Radiation, toxicity and similar hazards 28 Annexes30 Annex N (normative) Proof tracking test 30 Bibliography33 Figure 101 Splash apparatus 29 BS EN 60335-2-36:2002+A11:2
43、012 EN 60335-2-36:2002+A11:2012 (E)Page 5Annex ZE (normative).31Specific additional requirements for appliances and machines withAnnex ZZ (normative) Coverage of Essential Requirements of EU Directives .33power driven moving parts and intended for commercial use hiINTRODUCTION It has been assumed in
44、 the drafting of this International Standard that the execution of its provisions is entrusted to appropriately qualified and experienced persons. This standard recognizes the internationally accepted level of protection against hazards such as electrical, mechanical, thermal, fire and radiation of
45、appliances when operated as in normal use taking into account the manufacturers instructions. It also covers abnormal This standard takes into account the requirements of IEC 60364 as far as possible so that there is compatibility with the wiring rules when the appliance is connected to the supply m
46、ains. However, national wiring rules may differ. If an appliance within the scope of this standard also incorporates functions that are covered by another part 2 of IEC 60335, the relevant part 2 is applied to each function separately, as far as is reasonable. If applicable, the influence of one fun
47、ction on the other is taken into account. An appliance that complies with the text of this standard will not necessarily be considered to comply with the safety principles of the standard if, when examined and tested, it is found to have other features that impair the level of safety covered by thes
48、e requirements. An appliance employing materials or having forms of construction differing from those detailed in the requirements of this standard may be examined and tested according to the intent of the requirements and, if found to be substantially equivalent, may be considered to comply with th
49、e standard. When a part 2 standard does not include additional requirements to cover hazards dealt with in Part 1, Part 1 applies. NOTE 1 This means that the technical committees responsible for the part 2 standards have determined that it is not necessary to specify particular requirements for the appliance in question over and above the general requirements. This standard is a product family standard dealing with the safety of appliances and takes precedence
