1、BRITISH STANDARDBS EN 60512-15-2:2008Connectors for electronic equipment Tests and measurements Part 15-2: Connector tests (mechanical) Test 15b: Insert retention in housing (axial) ICS 31.220.10g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g3
2、8g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58BS EN 60512-15-2:2008This British Standard was published under the authority of the Standards Policy and Strategy Committee on 30 September 2008 BSI 2008ISBN 978 0 580 55900 6National forewordThis British
3、Standard is the UK implementation of EN 60512-15-2:2008. It is identical to IEC 60512-15-2:2008.The UK participation in its preparation was entrusted to Technical Committee EPL/48, Electromechanical components and mechanical structures for electronic equipment.A list of organizations represented on
4、this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obligations.Amendments/corrigenda
5、 issued since publicationDate CommentsEUROPEAN STANDARD EN 60512-15-2 NORME EUROPENNE EUROPISCHE NORM July 2008 CENELEC European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee fr Elektrotechnische Normung Central Secretariat: rue de
6、 Stassart 35, B - 1050 Brussels 2008 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members. Ref. No. EN 60512-15-2:2008 E ICS 31.220.10 English version Connectors for electronic equipment - Tests and measurements - Part 15-2: Connector tests (mechan
7、ical) - Test 15b: Insert retention in housing (axial) (IEC 60512-15-2:2008) Connecteurs pour quipements lectroniques - Essais et mesures - Partie 15-2: Essais (mcaniques) des connecteurs - Essai 15b: Rtention de lisolant dans le botier (axial) (CEI 60512-15-2:2008) Steckverbinder fr elektronische Ei
8、nrichtungen - Mess- und Prfverfahren - Teil 15-2: Mechanische Prfungen an Steckverbindern - Prfung 15b: Haltekraft des Einsatzes im Gehuse (axial) (IEC 60512-15-2:2008) This European Standard was approved by CENELEC on 2008-07-01. CENELEC members are bound to comply with the CEN/CENELEC Internal Reg
9、ulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CENELEC member. T
10、his European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the Central Secretariat has the same status as the official versions. CENELEC memb
11、ers are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Sloven
12、ia, Spain, Sweden, Switzerland and the United Kingdom. Foreword The text of document 48B/1844/FDIS, future edition 1 of IEC 60512-15-2, prepared by SC 48B, Connectors, of IEC TC 48, Electromechanical components and mechanical structures for electronic equipment, was submitted to the IEC-CENELEC para
13、llel vote and was approved by CENELEC as EN 60512-15-2 on 2008-07-01. This standard is to be read in conjunction with EN 60512-1 and EN 60512-1-100 which explains the structure of the EN 60512 series. The following dates were fixed: latest date by which the EN has to be implemented at national level
14、 by publication of an identical national standard or by endorsement (dop) 2009-04-01 latest date by which the national standards conflicting with the EN have to be withdrawn (dow) 2011-07-01 Annex ZA has been added by CENELEC. _ Endorsement notice The text of the International Standard IEC 60512-15-
15、2:2008 was approved by CENELEC as a European Standard without any modification. _ BS EN 60512-15-2:2008 2 CONNECTORS FOR ELECTRONIC EQUIPMENT TESTS AND MEASUREMENTS Part 15-2: Connector tests (mechanical) Test 15b: Insert retention in housing (axial) 1 Scope and object This part of IEC 60512, when r
16、equired by the detail specification, is used for testing connectors within the scope of technical committee 48. It may also be used for similar devices when specified in a detail specification. The object of this document is to detail a standard test method to assess the effectiveness of the insert
17、retaining system to withstand axial loads likely to be encountered during normal use. NOTE The test method detailed in this document is a companion to the one detailed in IEC 60512-15-3 (see bibliographic reference). 2 Normative references The following referenced documents are indispensable for the
18、 application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. IEC 60512-1-1, Connectors for electronic equipment Tests and measurements Part 1-1: General examination Test
19、1a: Visual examination 3 Preparations 3.1 Preparation of specimen The specimen shall consist of a connector with its terminations, and may be wired if so specified in the detail specification. Cable fittings and accessories shall not be fitted. Any preconditioning given in the detail specification s
20、hall be applied. 3.2 Equipment For the application of the axial loads, a suitable device able to provide the controls on the loads (intensity, rate of increase, time of constant load application) shall be required (e.g.: a universal materials testing machine). In the case of the axial loads being ap
21、plied by air or gas pressure, a chamber to contain connectors that may be ejected in case of retention failure shall be provided. If hydraulic pressure is used, such a chamber may not be necessary. However compatibility between materials contained within the specimen and such fluids must be ensured.
22、 NOTE 1 Where air pressure is used, there is a possibility that contacts, inserts or other objects being ejected at high velocity. NOTE 2 If the detail specification requires special preconditioning of the specimen, all the necessary equipment detailed in the relevant documents describing such condi
23、tioning would also be required. BS EN 60512-15-2:2008 3 3.3 Mounting Mounting of the specimen shall be as specified in the detail specification. 4 Test method 4.1 Procedure Unless otherwise stated in the detail specification, 3 connectors shall be tested. 4.1.1 Force method The housing of the connec
24、tor shall be fixed in such a manner as not to influence the insert retention means. A specified axial force shall be applied in both directions consecutively, at a constant rate of 25 mm/min, until the specified force is achieved. This shall then be maintained for 1 minute. 4.1.2 Pressure method The
25、 displacement caused by the specified force or pressure if any shall be measured. Any residual displacement after the specified force or pressure is removed if any shall be measured. These displacements shall be recorded. The axial displacement of the insert shall not exceed that which may be given
26、in the detail specification. 4.2 Measurements 4.2.1 Before testing Visual examination according to IEC 60512-1-1 shall be done. 4.2.2 During testing There shall be no displacement of the insert during or after the test that would impair the normal operation of the connector. 4.2.3 After testing Visu
27、al examination according to IEC 60512-1-1 shall be done. 5 Details to be specified When this test is required by a detail specification, the following shall be given therein: a) the number of connectors to test if other than 3; b) preconditioning required; c) wiring of the specimen; d) mounting of t
28、he specimen; e) axial load or pressure to be applied; f) permitted displacement, if any (during and after the test); g) any deviation from the standard test method. BS EN 60512-15-2:2008 4 Bibliography IEC 60512-15-3, Connectors for electronic equipment Tests and measurements Part 15-3: Connector te
29、sts (mechanical) Test 15c: Insert retention in housing (torsional) _ NOTE Harmonized as EN 60512-15-3:2008 (not modified). BS EN 60512-15-2:2008 5 Annex ZA(normative) Normative references to international publications with their corresponding European publications The following referenced documents
30、are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE When an international publication has been modified by common modifications, in
31、dicated by (mod), the relevant EN/HD applies. Publication Year Title EN/HD Year IEC 60512-1-1 -1)Connectors for electronic equipment - Tests and measurements - Part 1-1: General examination - Test 1a: Visual examination EN 60512-1-1 20022)1)Undated reference. 2)Valid edition at date of issue. BS EN
32、60512-15-2:2008 6 blankBS EN 60512-15-2:2008BSI Group Headquarters389 Chiswick High Road,London W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards Institution (BSI)BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Eu
33、rope and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our produc
34、ts and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000 Fax: +44 (0)20 8996 7400BSI o
35、ffers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001 Fax:
36、+44 (0)20 8996 7001 Email: You may also buy directly using a debit/credit card from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested.
37、Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Cont
38、act the Information Centre. Tel: +44 (0)20 8996 7111 Fax: +44 (0)20 8996 7048 Email: Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administrat
39、ion. Tel: +44 (0)20 8996 7002 Fax: +44 (0)20 8996 7001 Email: Information regarding online access to British Standards via British Standards Online can be found at http:/ information about BSI is available on the BSI website at http:/.CopyrightCopyright subsists in all BSI publications. BSI also hol
40、ds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recordin
41、g or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070 Email:
