1、BSI Standards PublicationRadio-frequency connectorsPart 51: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock Characteristic impedance 50 O (type QLI)BS EN 61169-51:2015National forewordThis British Standard is the UK implementation o
2、f EN 61169-51:2015. It isidentical to IEC 61169-51:2015.The UK participation in its preparation was entrusted to TechnicalCommittee EPL/46, Cables, wires and waveguides, radio frequency connectors and accessories for communication and signalling.A list of organizations represented on this committee
3、can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisions ofa contract. Users are responsible for its correct application. The British Standards Institution 2015.Published by BSI Standards Limited 2015ISBN 978 0 580 82918 5ICS 33.120.30Compl
4、iance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards Policy and Strategy Committee on 30 June 2015.Amendments/corrigenda issued since publicationDate Text affectedBRITISH STANDARDBS EN 61169-51:2015EUROPEAN
5、 STANDARD NORME EUROPENNE EUROPISCHE NORM EN 61169-51 May 2015 ICS 33.120.30 English Version Radio-frequency connectors - Part 51: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock - Characteristic impedance 50 O (type QLI) (IEC 61169
6、-51:2015) Connecteurs pour frquences radiolectriques - Partie 51: Spcification intermdiaire relative aux connecteurs coaxiaux pour frquences radiolectriques avec diamtre intrieur des conducteurs extrieurs de 13,5 mm verrouillage baonnette - Impdance caractristique 50 O (type QLI) (IEC 61169-51:2015)
7、 Hochfrequenz-Steckverbinder - Teil 51: Rahmenspezifikation fr koaxiale HF Steckverbinder mit 13,5 mm Innendurchmesser des Auenleiters und Bajonettverschluss - Wellenwiderstand 50 Ohm (Typ QLI) (IEC 61169-51:2015) This European Standard was approved by CENELEC on 2015-03-12. CENELEC members are boun
8、d to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CE
9、N-CENELEC Management Centre or to any CENELEC member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CENELEC member into its own language and notified to the CEN-CENELEC Management
10、Centre has the same status as the official versions. CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Croatia, Cyprus, the Czech Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland,
11、Italy, Latvia, Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. European Committee for Electrotechnical Standardization Comit Europen de Normalisation Electrotechnique Europisches Komitee
12、fr Elektrotechnische Normung CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2015 CENELEC All rights of exploitation in any form and by any means reserved worldwide for CENELEC Members. Ref. No. EN 61169-51:2015 E BS EN 61169-51:2015EN 61169-51:2015 - 2 - Foreword The text of docume
13、nt 46F/295/FDIS, future edition 1 of IEC 61169-51, prepared by SC 46F “R.F. and microwave passive components“, of IEC/TC 46 “Cables, wires, waveguides, R.F. connectors, R.F. and microwave passive components and accessories“ was submitted to the IEC-CENELEC parallel vote and approved by CENELEC as EN
14、 61169-51:2015. The following dates are fixed: latest date by which the document has to be implemented at national level by publication of an identical national standard or by endorsement (dop) 2015-12-12 latest date by which the national standards conflicting with the document have to be withdrawn
15、(dow) 2018-03-12 Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CENELEC and/or CEN shall not be held responsible for identifying any or all such patent rights. Endorsement notice The text of the International Standard IEC 61169-5
16、1:2015 was approved by CENELEC as a European Standard without any modification. BS EN 61169-51:2015- 3 - EN 61169-51:2015 Annex ZA (normative) Normative references to international publications with their corresponding European publications The following documents, in whole or in part, are normative
17、ly referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. NOTE 1 When an International Publication has been modified by comm
18、on modifications, indicated by (mod), the relevant EN/HD applies. NOTE 2 Up-to-date information on the latest versions of the European Standards listed in this annex is available here: www.cenelec.eu. Publication Year Title EN/HD Year IEC 60529 - Degrees of protection provided by enclosures (IP Code
19、) - - IEC 61169-1 2013 Radio-frequency connectors - Part 1: Generic specification - General requirements and measuring methods EN 61169-1 2013 IEC 62037 series Passive RF and microwave devices, intermodulation level measurement EN 62037 series ISO 21207 - Corrosion tests in artificial atmospheres -
20、Accelerated corrosion tests involving alternate exposure to corrosion-promoting gases, neutral salt-spray and drying - - BS EN 61169-51:2015 2 IEC 61169-51:2015 IEC 2015 CONTENTS FOREWORD . 4 INTRODUCTION . 6 1 Scope 7 2 Normative references. 7 3 Mating face and gauge information . 8 3.1 Dimensions
21、General connectors . 8 Connector with socket-centre contact . 8 3.1.1Connector with pin-centre contact. 12 3.1.23.2 Gauges for connector with socket-centre contact . 14 Centre contact . 14 3.2.1Test procedure . 14 3.2.2Gauge for outer contact 15 3.2.34 Quality assessment procedures . 15 4.1 General
22、. 15 4.2 Ratings and characteristics . 15 4.3 Periodic tests 18 4.4 Procedures for the qualification approval . 20 Quality conformance inspection 20 4.4.1Qualification approval and its maintenance . 20 4.4.25 Instructions for preparation of detail specifications (DS) . 20 5.1 General . 20 5.2 Identi
23、fication of the component 20 5.3 Performances 21 5.4 Marking, ordering information and related matters 21 5.5 Selection of tests, test conditions and severities 21 5.6 Blank detail specification pro-forma for type QLI connector 22 6 Marking . 27 6.1 Marking of component . 27 6.2 Marking and contents
24、 of package 27 Figure 1 Connector with socket-centre contact with 2 options (for dimensions and key, see Table 1) 8 Figure 2 Detail of bayonet lock groove, option 1 (for dimensions and key, see Table 1) . 9 Figure 3 Detail of bayonet lock groove, option 2 (for dimensions and key, see Table 1) . 9 Fi
25、gure 4 Female centre contact (for dimensions and key, see Table 1 . 10 Figure 5 Connector with pin-centre contact (for dimensions and key, see Table 2) . 12 Figure 6 Details of pin-centre contact (for dimensions, see Table 2) 12 Figure 7 Gauge pin for socket-centre contact (for dimensions, see Table
26、 3) . 14 Figure 8 Gauge ring for socket outer contact (for dimensions, see Table 4) . 15 BS EN 61169-51:2015IEC 61169-51:2015 IEC 2015 3 Table 1 Dimensions of connector with socket-centre contact . 11 Table 2 Dimensions of connector with pin-centre contact 13 Table 3 Gauge dimensions for socket-cent
27、re contact 14 Table 4 Dimensions of gauge ring for socket outer contact 15 Table 5 Rating and characteristics 16 Table 6 Acceptance tests . 18 Table 7 Periodic tests 19 BS EN 61169-51:2015 4 IEC 61169-51:2015 IEC 2015 INTERNATIONAL ELECTROTECHNICAL COMMISSION _ RADIO-FREQUENCY CONNECTORS Part 51: Se
28、ctional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock Characteristic impedance 50 (type QLI) FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotech
29、nical committees (IEC National Committees). The object of IEC is to promote international co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications
30、, Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, go
31、vernmental and non-governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decision
32、s or agreements of IEC on technical matters express, as nearly as possible, an international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for internati
33、onal use and are accepted by IEC National Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order
34、to promote international uniformity, IEC National Committees undertake to apply IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearl
35、y indicated in the latter. 5) IEC itself does not provide any attestation of conformity. Independent certification bodies provide conformity assessment services and, in some areas, access to IEC marks of conformity. IEC is not responsible for any services carried out by independent certification bod
36、ies. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and members of its technical committees and IEC National Committees for any personal injury, propert
37、y damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in thi
38、s publication. Use of the referenced publications is indispensable for the correct application of this publication. International Standard IEC 61169-51 has been prepared by subcommittee 46F: R.F. and microwave passive components, of IEC technical committee 46: Cables, wires, waveguides, R.F. connect
39、ors, R.F. and microwave passive components and accessories. The text of this standard is based on the following documents: FDIS Report on voting 46F/295/FDIS 46F/310/RVD Full information on the voting for the approval of this standard can be found in the report on voting indicated in the above table
40、. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. BS EN 61169-51:2015IEC 61169-51:2015 IEC 2015 5 A list of all parts of the IEC 61169 series, under the general title: Radio-frequency connectors, can be found on the IEC website. The committee has decided that the
41、 contents of this publication will remain unchanged until the stability date indicated on the IEC web site under “http:/webstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. IMPORTANT
42、 The colour inside logo on the cover page of this publication indicates that it contains colours which are considered to be useful for the correct understanding of its contents. Users should therefore print this document using a colour printer. BS EN 61169-51:2015 6 IEC 61169-51:2015 IEC 2015 INTROD
43、UCTION The international Electrotechnical Commission (IEC) draws attention to the fact that it is claimed that compliance with this document may involve the use of a patent concerning the design of the connector given in 3.1. IEC takes no position concerning the evidence, validity and scope of this
44、patent right. The holder of this patent right has assured the IEC that he/she is willing to negotiate licence under reasonable and non-discriminatory terms and conditions with applicants throughout the world. In this respect, the statement of the holders of this patent right is registered with IEC.
45、More detailed information may be obtained from: Radiall SA Mr. Pierre Bigot, RFI Division P Phone:+33 47 650 0057 Z.I Centralp 642 rue Emile Romanet, B.P. 35 F-38341 Voreppe Cedex, France Attention is drawn to the possibility that some of elements of this document may be the subject of patent rights
46、 other than those identified above. IEC shall not be held responsible for identifying any or all such patent rights. ISO (www.iso.org/patents) and IEC (http:/patents.iec.ch) maintain on-line data bases of patents relevant to their standards. Users are encouraged to consult the data bases for the mos
47、t up to date information concerning patents. BS EN 61169-51:2015IEC 61169-51:2015 IEC 2015 7 RADIO-FREQUENCY CONNECTORS Part 51: Sectional specification for RF coaxial connectors with inner diameter of outer conductors 13,5 mm with bayonet lock Characteristic impedance 50 (type QLI) 1 Scope This par
48、t of IEC 61169, which is a sectional specification (SS), provides information and rules for the preparation of detail specifications (DS) for type QLI R.F. coaxial connectors with quick lock. The connectors are normally used with 50 corrugated cable and flexible cables for middle power applications
49、in an operating range up to 6 GHz. It describes the interface dimensions for general purpose connectors with gauging information and the mandatory tests selected from IEC 61169-1 applicable to all detail specifications relative to type QLI connectors. This specification indicates the recommended performance characteristics to be considered when writing a DS and covers all tests schedules and inspection requirement
