1、BS EN ISO10325:2009ICS 59.080.50NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDFibre ropes Highmodulus polyethylene 8-strand braidedropes, 12-strandbraided ropes andcovered ropes (ISO10325:2009)This British Standardwas published under theauthority of the Standa
2、rdsPolicy and StrategyCommittee on 31 January2010 BSI 2010ISBN 978 0 580 61328 9Amendments/corrigenda issued since publicationDate CommentsBS EN ISO 10325:2009National forewordThis British Standard is the UK implementation of EN ISO 10325:2009.The UK participation in its preparation was entrusted to
3、 TechnicalCommittee TCI/77, Ropes and cordage and fishing nets.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Co
4、mpliance with a British Standard cannot confer immunityfrom legal obligations.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN ISO 10325 December 2009 ICS 59.080.50 English Version Fibre ropes - High modulus polyethylene - 8-strand braided ropes, 12-strand braided ropes and covered ropes (ISO 10
5、325:2009) Cordages en fibres - Polythylne haut module - Cordages 8 torons, cordages 12 torons et cordages avec couverture (ISO 10325:2009) Faserseile - Hochmodulares Polyethylen - 8-litzige geflochtene Seile, 12-litzige geflochtene Seile und ummantelte Seile (ISO 10325:2009) This European Standard w
6、as approved by CEN on 4 November 2009. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such
7、national standards may be obtained on application to the CEN Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language
8、and notified to the CEN Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxemb
9、ourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG Management Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All right
10、s of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN ISO 10325:2009: EBS EN ISO 10325:2009EN ISO 10325:2009 (E) 3 Foreword This document (EN ISO 10325:2009) has been prepared by Technical Committee ISO/TC 38 “Textiles“ in collaboration with Technica
11、l Committee CEN/TC 248 “Textiles and textile products” the secretariat of which is held by BSI. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by June 2010, and conflicting national standards shall
12、be withdrawn at the latest by June 2010. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying any or all such patent rights. According to the CEN/CENELEC Internal Regulat
13、ions, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherl
14、ands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. Endorsement notice The text of ISO 10325:2009 has been approved by CEN as a EN ISO 10325:2009 without any modification. BS EN ISO 10325:2009ISO 10325:2009(E) ISO 2009 All rights reserved i
15、iiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a
16、 technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matte
17、rs of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circula
18、ted to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsibl
19、e for identifying any or all such patent rights. ISO 10325 was prepared by Technical Committee ISO/TC 38, Textiles. BS EN ISO 10325:2009BS EN ISO 10325:2009INTERNATIONAL STANDARD ISO 10325:2009(E) ISO 2009 All rights reserved 1Fibre ropes High modulus polyethylene 8-strand braided ropes, 12-strand b
20、raided ropes and covered ropes 1 Scope This International Standard specifies requirements for 8-strand braided ropes, for 12-strand braided ropes, and for covered rope constructions made of high modulus polyethylene (HMPE), and gives rules for their designation. 2 Normative references The following
21、referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1968, Fibre ropes and cordage Vocabulary ISO 2307, Fibre ro
22、pes Determination of certain physical and mechanical properties ISO 9554:2005, Fibre ropes General specifications 3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 1968 and the following apply. 3.1 cover jacket braided cover or other protective layer,
23、which is placed over the rope core NOTE The cover has no significant contribution to the rope strength. 4 Designation Fibre ropes shall be designated by the following: the words “fibre rope”; the number of this International Standard; the construction type of the rope; the reference number of the ro
24、pe; BS EN ISO 10325:2009ISO 10325:2009(E) 2 ISO 2009 All rights reserved the material from which the rope is made. EXAMPLE Designation of a 12-strand braided rope, reference number 20 (type T), corresponding to a linear density of 232 ktex made of high modulus polyethylene (HMPE): Fibre rope ISO 103
25、25 T 20 HMPE 5 Material 5.1 The ropes shall be made of continuous HMPE fibres. Different HMPE fibre grades may have different creep properties. If requested, the manufacturer shall provide information about creep properties. 5.2 Coating may be applied to the rope for property enhancement purposes. 5
26、.3 Concerning covered ropes, the cover may consist of a variety of fibre materials, for example, polyester, polyolefins, HMPE. 5.4 The typical characteristics of high modulus polyethylene fibre are indicated in Table A.1 of ISO 9554:2005. NOTE Ropes constructed from 100 % HMPE fibres float. However,
27、 covered HMPE ropes can have a higher linear density and might sink. HMPE fibres have a good resistance to axial compression resulting in a good intrinsic bending fatigue resistance. HMPE fibres have a low coefficient of friction and good abrasion resistance. The coefficient of friction can be alter
28、ed by applying suitable coatings. 6 General requirements 6.1 General HMPE fibre ropes shall be made in one of the following constructions: type L 8-strand braided ropes (see Figure 1) type T 12-strand braided ropes (see Figure 2) type C covered ropes see Figures 3 a) and 3 b) 6.2 Construction, manuf
29、acture and lay length 6.2.1 The construction, manufacture and lay length of 8-strand ropes and of 12-strand ropes shall conform to ISO 9554. 6.2.2 In the construction of covered ropes, the rope core is protected by a non-load-bearing cover. The construction, manufacture and lay length of the rope co
30、re or sub-ropes shall conform to ISO 9554. NOTE The core or the sub-ropes can have various constructions. 6.2.3 In the protective cover, strand interchanges, i.e. the overlapping continuation of an interrupted strand with another identical strand following the same path, are permitted if they are pr
31、operly staggered. 6.3 Labelling, packaging, invoicing and delivered lengths Labelling, packaging, invoicing and delivered lengths shall conform to ISO 9554. BS EN ISO 10325:2009ISO 10325:2009(E) ISO 2009 All rights reserved 37 Physical properties The linear density and minimum breaking force shall c
32、onform to Tables 1 and 2. 8 Marking The manufacturer may use coloured synthetic yarn(s) to identify its rope. The manufacturer may apply a coloured coating to identify its rope. A printed marker tape shall be used in accordance with ISO 9554. Figure 1 Shape of an 8-strand braided rope (type L) Figur
33、e 2 Shape of a 12-strand braided rope (type T) a) Single rope core b) Multiple cores: 3-strand cores Figure 3 Shape of a covered rope (type C) BS EN ISO 10325:2009ISO 10325:2009(E) 4 ISO 2009 All rights reservedTable 1 Linear density and minimum breaking force of 8-strand (type L) and 12-strand (typ
34、e T) HMPE braided ropes Linear densitybcMinimum breaking forcedekN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 6 23,0 36,7 33,0 8 40,0 10 65,3 58,7 10 61,0 102 92,0 12 87,0 147 132 14 117 8 200 180 16 151 260 235 18 190 310 283 20 232 380 340 22 281
35、450 400 24 331 520 470 26 384 600 540 28 445 680 610 30 506 770 690 32 575 870 780 34 648 960 860 36 720 1 040 940 38 798 1 160 1 040 40 881 5 1 260 1 130 44 1 060 1 460 1 310 48 1 250 1 700 1 530 52 1 460 1 970 1 770 56 1 690 2 260 2 030 60 1 930 2 530 2 280 64 2 200 2 840 2 560 68 2 480 3 170 2 85
36、0 72 2 780 3 520 3 170 76 3 090 3 890 3 500 80 3 430 4 300 3 870 88 4 170 5 200 4 680 96 4 970 6 180 5 560 aThe reference number corresponds to the approximate diameter, in millimetres. bThe linear density, in kilotex, corresponds to the net mass per length of the rope, expressed in grams per metre
37、or in kilograms per kilometre. cThe linear density is obtained under reference tension and is measured as specified in ISO 2307. dThe breaking forces relate to new, dry and wet ropes. eA force determined by the test methods specified in ISO 2307 is not necessarily an accurate indication of the force
38、 at which that rope might break in other circumstances and situations. The type and quality of terminations, the rate of force application, prior conditioning and previous force applications to the rope can significantly influence the breaking force. A rope bent around a post, capstan, pulley or she
39、ave might break at a significantly lower force. A knot or other distortion in a rope might significantly reduce the breaking force.BS EN ISO 10325:2009ISO 10325:2009(E) ISO 2009 All rights reserved 5Table 2 Linear density and minimum breaking force of covered HMPE ropes (type C) Linear densitybcMini
40、mum breaking forcede kN Reference numberaNominal ktex Tolerance % Unspliced ropes Ropes with eye-spliced terminations 20 240 271 244 22 290 341 307 24 340 402 362 26 400 471 424 28 460 549 494 30 530 637 573 32 600 736 662 34 680 824 742 36 770 912 821 38 850 1 010 909 40 940 1 140 1 030 44 1 150 10
41、 1 380 1 240 48 1 360 1 610 1 450 52 1 600 1 920 1 730 56 1 850 2 190 1 970 60 2 120 2 520 2 270 64 2 400 2 880 2 590 68 2 720 3 260 2 930 72 3 070 3 630 3 270 76 3 400 4 020 3 620 80 3 750 4 510 4 060 88 4 500 5 350 4 820 96 5 300 6 280 5 650 aThe reference number corresponds to the approximate dia
42、meter, in millimetres. bThe linear density, in kilotex, corresponds to the net mass per length of the rope, expressed in grams per metre or in kilograms per kilometre. cThe linear density is obtained under reference tension and is measured as specified in ISO 2307. dThe breaking forces relate to new
43、, dry and wet ropes. eA force determined by the test methods specified in ISO 2307 is not necessarily an accurate indication of the force at which that rope might break in other circumstances and situations. The type and quality of terminations, the rate of force application, prior conditioning and
44、previous force applications to the rope can significantly influence the breaking force. A rope bent around a post, capstan, pulley or sheave might break at a significantly lower force. A knot or other distortion in a rope might significantly reduce the breaking force. BS EN ISO10325:2009BSI GroupHea
45、dquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at theinternational level. It is incorporate
46、d by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and services.We would be grateful if anyone finding a
47、n inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS w
48、hich ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967001 Email: You may also buy directly using
49、a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electr
