1、BRITISH STANDARD BS EN ISO 16585:2002 Incorporating Corrigenda Nos. 1 and 2 Closed end blind rivets with pull mandrel and protruding head A2/SSt The European Standard EN ISO 16585:2002 has the status of a British Standard ICS 21.060.40 BS EN ISO 16585:2002 This British Standard, having been prepared
2、 under the direction of the Engineering Sector Policy and Strategy Committee, was published under the authority of the Standards Policy and Strategy Committee on 21 November 2002 BSI 23 November 2004 ISBN 0 580 40776 4 National foreword This British Standard is the official English language version
3、of EN ISO 16585:2002. It is identical with ISO 16585:2002. BS EN ISO 16585:2002, together with BS EN ISO 15980:2002, BS EN ISO 15981:2002, BS EN ISO 15982:2002, BS EN ISO 15983:2002, BS EN ISO 15984:2002, BS EN ISO 16582:2002, BS EN ISO 16583:2002 and BS EN ISO 16584:2002, supersedes BS 7349-2:1993
4、which is withdrawn. The UK participation in its preparation was entrusted to Technical Committee FME/6, Rivets, which has the responsibility to: A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement i
5、nternational or European publications referred to in this document may be found in the BSI Catalogue under the section entitled “International Standards Correspondence Index”, or by using the “Search” facility of the BSI Electronic Catalogue or of British Standards Online. This publication does not
6、purport to include all the necessary provisions of a contract. Users are responsible for its correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. aid enquirers to understand the text; present to the responsible international/European comm
7、ittee any enquiries on the interpretation, or proposals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. Summary of pages This document comprises a front cover, an inside front cover, the EN ISO title page, the EN
8、ISO foreword page, the ISO title page, pages ii and iii, a blank page, pages 1 to 5, the Annex ZA page, an inside back cover and a back cover. The BSI copyright notice displayed in this document indicates when the document was last issued. Amendments issued since publication Amd. No. Date Comments 1
9、4314 Corrigendum No. 1 24 January 2003 Replacing the EN ISO foreword page and incorporating the Annex ZA page 15328 Corrigendum No. 2 23 November 2004 Addition of supersession details.EUROPEANSTANDARD NORMEEUROPENNE EUROPISCHENORM ENISO16585 November2002 ICS21.060.40 Englishversion Closedendblindriv
10、etswithpullmandrelandprotrudinghead A2/SSt(ISO16585:2002) Rivetsaveuglesrupturedetigecorpsferm,tte bombeA2/SSt(ISO16585:2002) GeschlosseneBlindnietemitSollbruchdornundFlachkopf A2/SSt(ISO16585:2002) ThisEuropeanStandardwasapprovedbyCENon14October2002. CENmembersareboundtocomplywiththeCEN/CENELECInte
11、rnalRegulationswhichstipulatetheconditionsforgivingthisEurope an Standardthestatusofanationalstandardwithoutanyalteration.Uptodatelistsandbibliographicalreferencesconcernings uchnational standardsmaybeobtainedonapplicationtotheManagementCentreortoanyCENmember. ThisEuropeanStandardexistsinthreeoffici
12、alversions(English,French,German).Aversioninanyotherlanguagemadebytra nslation undertheresponsibilityofaCENmemberintoitsownlanguageandnotifiedtotheManagementCentrehasthesamestatusasthe official versions. CENmembersarethenationalstandardsbodiesofAustria,Belgium,CzechRepublic,Denmark,Finland,France,Ge
13、rmany,Greece, Iceland,Ireland,Italy,Luxembourg,Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandUnitedKingdom. EUROPEANCOMMITTEEFORSTANDARDIZATION COMITEUROPENDENORMALISATION EUROPISCHESKOMITEEFRNORMUNG ManagementCentre:ruedeStassart,36B1050Brussels 2002CEN Allrightsofexploitationinanyfo
14、rmandbyanymeansreserved worldwideforCENnationalMembers. Ref.No.ENISO16585:2002ECORRECTED20021218 Foreword Thisdocument(ENISO16585:2002)hasbeenpreparedbyTechnicalCommitteeISO/TC2 “Fasteners“incollaborationwithTechnicalCommitteeCEN/TC185“Threadedandnon threadedmechanicalfastenersandaccessories“,thesec
15、retariatofwhichisheldbyDIN. ThisEuropeanStandardshallbegiventhestatusofanationalstandard,eitherbypublicationof anidenticaltextorbyendorsement,atthelatestbyMay2003,andconflictingnationalstandards shallbewithdrawnatthelatestbyMay2003. AccordingtotheCEN/CENELECInternalRegulations,thenationalstandardsor
16、ganizationsof thefollowingcountriesareboundtoimplementthisEuropeanStandard:Austria,Belgium,Czech Republic,Denmark,Finland,France,Germany,Greece,Iceland,Ireland,Italy,Luxembourg, Malta,Netherlands,Norway,Portugal,Spain,Sweden,SwitzerlandandtheUnitedKingdom. Endorsementnotice ThetextofISO16585:2002has
17、beenapprovedbyCENasENISO16585:2002withoutany modifications. NOTENormativereferencestoInternationalStandardsarelistedinAnnexZA(normative). ENISO16585:2002 Reference number ISO 16585:2002(E)INTERNATIONAL STANDARD ISO 16585 First edition 2002-11-01 Closed end blind rivets with pull mandrel and protrudi
18、ng head A2/SSt Rivets aveugles rupture de tige corps ferm, tte bombe A2/SSt ENISO16585:2002ENISO16585:2002ii Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is
19、normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part
20、in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to pre
21、pare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that
22、some of the elements of this International Standard may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 16585 was prepared by Technical Committee ISO/TC 2, Fasteners. Annex A of this International Standard is for information only.
23、 ENISO16585:2002iiiINTENRATIONAL TSANDADR IS:58561 O2002(E)I SO 2002 All irthgs ersedevr 1Closed end blind rivets with pull mandrel and protruding head A2/SSt 1 Scope This International Standard specifies dimensional and mechanical characteristics and application data for closed end blind rivets wit
24、h break pull mandrel and protruding head, with an austenitic stainless-steel body (A2) and a stainless-steel mandrel (SSt) and with nominal diameters, d, from 3,2 mm up to and including 6,4 mm. 2 Normative references The following normative documents contain provisions which, through reference in th
25、is text, constitute provisions of this International Standard. For dated references, subsequent amendments to, or revisions of, any of these publications do not apply. However, parties to agreements based on this International Standard are encouraged to investigate the possibility of applying the mo
26、st recent editions of the normative documents indicated below. For undated references, the latest edition of the normative document referred to applies. Members of ISO and IEC maintain registers of currently valid International Standards. ISO 3269:2000, Fasteners Acceptance inspection ISO 3506-1:199
27、7, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws and studs ISO 14588:2000, Blind rivets Terminology and definitions ISO 14589:2000, Blind rivets Mechanical testing 3 Dimensions 3.1 General Symbols and designations of dimensions are specified in ISO 1458
28、8. 3.2 Rivets dimensions See Figure 1 and Table 1. ENISO16585:20021IS:58561 O2002(E) 2 I SO 2002 All irthgs ersedevrFigure 1 Rivet dimensions Table 1 Rivet dimensions Dimensions in millimetres nom. 3,2 4 4,8 6,4 max. 3,28 4,08 4,88 6,48 d min. 3,05 3,85 4,65 6,25 max. 6,7 8,4 10,1 13,4 d kmin. 5,8 6
29、,9 8,3 11,6 Rivet body k max. 1,3 1,7 2 2,7 d mmax. 2,15 2,75 3,2 3,9 Mandrel p min. 25 25 27 27 Rivet length l nom. = min. max. Recommended grip ranges a6 7 0,5 to 1,5 0,5 to 1,5 8 9 1,5 to 3,0 1,5 to 3,0 0,5 to 3,0 10 11 3 to 5 3 to 5 3 to 5 12 13 5,0 to 6,5 5,0 to 6,5 5,0 to 6,5 1,5 to 6,5 14 15
30、6,5 to 8,0 6,5 to 8,0 16 17 8 to 11 6,5 to 9,0 6,5 to 8,0 20 21 9 to 12 8 to 12 NOTE The rivet body dimensions are generated from the design formulae specified in annex A. aThe grip ranges of rivets with dimensions as given in Table 1, with the material combination as given in clause 4, are specifie
31、d by the minimum and maximum grip lengths. The minimum grip lengths are recommendations only. It may be possible to go into individual cases below the minimum values. ENISO16585:20022IS:58561 O2002(E) I SO 2002 All irthgs ersedevr 33.3 Clearance hole diameters The diameters of the clearance holes, d
32、 h1 , to accommodate the rivet in the components to be fastened are given in Table 2. Table 2 Clearance hole diameters Dimensions in millimetres d d h1nom. min. max. 3,2 3,3 3,4 4 4,1 4,2 4,8 4,9 5,0 6,4 6,5 6,6 Non conformance to the values listed in Table 2 may result in assembly difficulties and/
33、or reduction in the shear and tensile loads specified in Table 3. When necessary, to facilitate alignment, only the component on the access side may have a clearance hole larger than specified in Table 2 (see Figure 2). This may also result in a reduction of the shear and tensile loads specified in
34、Table 3. aEnlarged clearance hole Figure 2 Enlarged clearance hole to facilitate alignment 4 Material and finish Blind rivets in accordance with this International Standard shall have a rivet body made of austenitic stainless-steel grade A2 in accordance with ISO 3506-1 and a stainless-steel mandrel
35、 (SSt) and shall also have mechanical properties as specified in clause 5. Material specification is at the discretion of the manufacturer. The surface of rivet body and mandrel shall be plain, i.e. in natural finish. ENISO16585:20023IS:58561 O2002(E) 4 I SO 2002 All irthgs ersedevr5 Mechanical prop
36、erties The minimum shear load, minimum tensile load and maximum mandrel break load shall be as specified in Table 3 when tested in accordance with ISO 14589. Table 3 Mechanical properties d Shear load Tensile load Mandrel break load nom. min. min. max. mm N N N 3,2 2 000 2 200 4 500 4 3 000 3 500 6
37、500 4,8 4 000 4 400 8 500 6,4 6 000 8 000 16 000 6 Workmanship Rivets shall be free from burrs and harmful defects and shall have well-formed heads and shanks. After setting, rivets shall not show evidence of cracking when viewed at 5 magnification. 7 Acceptance testing If there is no other agreemen
38、t, acceptance inspection in accordance with ISO 3269 applies. 8 Designation EXAMPLE A closed end blind rivet, with break pull mandrel and protruding head, with nominal diameter d = 4 mm and nominal length l = 12 mm with an austenitic stainless-steel body (A2) and a stainless-steel mandrel (SSt) is d
39、esignated as follows: Blind rivet ISO 16585 - 4 12 - A2/SSt ENISO16585:20024IS:58561 O2002(E) I SO 2002 All irthgs ersedevr 5Annex A (informative) Design formulae A.1 General Blind rivets in accordance with this International Standard comply with the following design formulae and tolerances. A.2 Sha
40、nk diameter The maximum shank diameter complies with the formula: d max= d nom+ 0,08 mm The minimum shank diameter complies with the formula: d min= d nom 0,15 mm A.3 Head diameter The maximum head diameter complies with the formula: d k max= 2,1 d nomrounded to one decimal place. A.4 Head diameter
41、tolerance The head diameter tolerance is h16 for d nomu 3,2 mm and h17 for d nom 3,2 mm. A.5 Head height The maximum head height complies with the formula: k max= 0,415 d nomrounded to one decimal place. A.6 Clearance hole diameter The clearance hole diameter for blind rivet application complies wit
42、h the formulae: d h1 max= d nom+ 0,2 mm d h1 min= d nom+ 0,1 mm ENISO16585:20025AnnexZA (normative) Normativereferencestointernationalpublications withtheirrelevantEuropeanpublications ThisEuropeanStandardincorporatesbydatedorundatedreference,provisionsfromother publications.Thesenormativereferences
43、arecitedattheappropriateplacesinthetextandthe publicationsarelistedhereafter.Fordatedreferences,subsequentamendmentstoorrevisionsof anyofthesepublicationsapplytothisEuropeanStandardonlywhenincorporatedinitby amendmentorrevision.Forundatedreferencesthelatesteditionofthepublicationreferredto applies(i
44、ncludingamendments). NOTEWhereanInternationalPublicationhasbeenmodifiedbycommonmodifications,indicated by(mod.),therelevantEN/HDapplies. Publication Year Title EN Year ISO3269 2000 FastenersAcceptanceinspection ENISO3269 2000 ISO35061 1997 Mechanicalpropertiesof corrosionresistantstainlesssteel fast
45、enersPart1:Bolts,screws andstuds ENISO35061 1997 ISO14588 2000 BlindrivetsTerminologyand definitions ENISO14588 2000 ISO14589 2000 BlindrivetsMechanicaltesting ENISO14589 2000 ENISO16585:2002BS EN ISO 16585:2002 BSI 389 Chiswick High Road London W4 4AL BSI British Standards Institution BSI is the in
46、dependent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that
47、they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400. BSI offers members an individual updating service called PLUS which ensures that subscribers automa
