1、 ETSI EN 301 406 V2.2.1 (2016-04) Digital Enhanced Cordless Telecommunications (DECT); Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 406 V2.2.1 (2016-04) 2 Reference REN/DECT-000300 Keywords DECT, digi
2、tal, generic, radio, regulation, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The pr
3、esent document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of E
4、TSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that
5、 the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services:
6、 https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall n
7、ot be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for th
8、e benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI EN 301 406 V2.2.1 (2016-04) 3 Contents Intellectual Property
9、 Rights 10g3Foreword . 10g3Modal verbs terminology 10g31 Scope 11g32 References 11g32.1 Normative references . 11g32.2 Informative references 12g33 Definitions, symbols and abbreviations . 13g33.1 Definitions 13g33.2 Symbols 15g33.3 Abbreviations . 15g34 Technical requirements specifications . 16g34
10、.1 Environmental profile . 16g34.2 Overview 16g34.2.0 General 16g34.2.1 Test suites . 16g34.2.2 Test groups 17g34.2.3 Test cases 17g34.3 Applicants declaration . 17g34.4 Applicability of tests 18g34.4.0 Introduction. 18g34.4.1 Equipment that includes only a DECT RF receiver 18g34.4.2 Equipment that
11、includes a radio transmitter . 18g34.4.3 CTAs . 18g34.4.4 Equipment with combined FT and PT functionality . 18g34.4.4.0 General 18g34.4.4.1 Wireless Relay Station 18g34.4.4.2 Direct PP to PP communication 18g34.4.4.3 Distributed Communications. 19g34.4.5 Provision of 4 Mbit/s services. Equipment tha
12、t is capable of using higher level modulation . 19g34.4.6 Equipment supporting additional carriers . 19g34.5 Conformance requirements 19g34.5.1 Accuracy and stability of RF carriers . 19g34.5.1.1 Definition 19g34.5.1.2 Limits 19g34.5.1.3 Conformance . 20g34.5.2 Accuracy and stability of timing param
13、eters 20g34.5.2.0 General 20g34.5.2.1 Definitions. 20g34.5.2.1.1 Slot structure 20g34.5.2.1.2 Definition of the position of p0 . 20g34.5.2.2 Limits 20g34.5.2.3 Conformance . 20g34.5.3 Transmission burst 20g34.5.3.1 Definitions. 20g34.5.3.1.1 Physical packets. 20g34.5.3.1.2 Transmitted power . 20g34.
14、5.3.1.3 Normal Transmitted Power (NTP) 20g34.5.3.1.4 Transmitter attack time 20g34.5.3.1.5 Transmitter release time 21g34.5.3.1.6 Minimum power 21g34.5.3.1.7 Maximum power . 21g34.5.3.1.8 Maintenance of transmission after packet end . 21g34.5.3.1.9 Transmitter idle power output . 21g34.5.3.2 Limits
15、21g3ETSI ETSI EN 301 406 V2.2.1 (2016-04) 4 4.5.3.3 Conformance . 21g34.5.4 Transmitted power 21g34.5.4.1 Definitions . 21g34.5.4.1.0 Transceiver and PNTPdefinitions . 21g34.5.4.1.1 PP and RFP with an integral antenna 22g34.5.4.1.2 PP and RFP with external connections for all antennas 22g34.5.4.1.3
16、PP and RFP with both integral and external antennas . 22g34.5.4.2 Limits 22g34.5.4.3 Conformance . 22g34.5.4.4 Multi-transceiver systems . 22g34.5.5 RF carrier modulation . 22g34.5.5.1 Definition 22g34.5.5.2 Limits 22g34.5.5.3 Conformance . 22g34.5.6 Unwanted RF power radiation 23g34.5.6.1 General 2
17、3g34.5.6.2 Emissions due to modulation 23g34.5.6.2.1 Definition. 23g34.5.6.2.2 Limits 23g34.5.6.2.3 Conformance . 23g34.5.6.3 Emissions due to transmitter transients . 23g34.5.6.3.1 Definition. 23g34.5.6.3.2 Limits 23g34.5.6.3.3 Conformance . 23g34.5.6.4 Emissions due to intermodulation . 23g34.5.6.
18、4.1 Definition. 23g34.5.6.4.2 Limits 23g34.5.6.4.3 Conformance . 23g34.5.6.5 Spurious emissions when allocated a transmit channel . 23g34.5.6.5.1 Definition. 23g34.5.6.5.2 Limits 23g34.5.6.5.3 Conformance . 24g34.5.7 Radio receiver testing . 24g34.5.7.1 Radio receiver sensitivity 24g34.5.7.1.1 Defin
19、ition. 24g34.5.7.1.2 Limits 24g34.5.7.1.3 Conformance . 24g34.5.7.2 Radio receiver reference BER and FER 24g34.5.7.2.1 Definition. 24g34.5.7.2.2 Limits 24g34.5.7.2.3 Conformance . 24g34.5.7.3 Radio receiver interference performance 24g34.5.7.3.1 Definition. 24g34.5.7.3.2 Limits 24g34.5.7.3.3 Conform
20、ance . 24g34.5.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other frequencies 24g34.5.7.4.1 Definition. 24g34.5.7.4.2 Limits 24g34.5.7.4.3 Conformance . 25g34.5.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time 25g34.5.7.5.1
21、Definition. 25g34.5.7.5.2 Limits 25g34.5.7.5.3 Conformance . 25g34.5.7.6 Receiver intermodulation performance . 25g34.5.7.6.1 Definition. 25g34.5.7.6.2 Limits 25g34.5.7.6.3 Conformance . 25g34.5.7.7 Spurious emissions when the PP has no allocated transmit channel . 25g34.5.7.7.1 Definition. 25g34.5.
22、7.7.2 Limits 25g3ETSI ETSI EN 301 406 V2.2.1 (2016-04) 5 4.5.7.7.3 Conformance . 25g34.5.8 Channel access 25g34.5.8.1 Channel selection 25g34.5.8.2 Channel confirmation 26g34.5.8.2.1 For the PT 26g34.5.8.2.2 For the FT 26g34.5.8.3 Channel release . 26g34.5.8.4 General 26g34.5.8.5 Channel selection a
23、nd confirmation for DECT ULE 27g34.5.8.5.1 General 27g34.5.8.5.2 For the PT 27g34.5.8.5.3 For the FT 27g34.5.9 WRS testing 27g34.5.9.0 General requirements 27g34.5.9.1 Testing as a PP 27g34.5.9.2 Testing as an RFP . 28g34.5.9.3 Additional requirements 28g34.5.9.4 Conformance . 28g34.5.10 Requirement
24、s for PPs with direct PP to PP communication mode . 28g34.5.10.0 General requirements 28g34.5.10.1 Setting the EUT in direct communications mode 28g34.5.10.2 When the EUT has not initiated a call . 29g34.5.10.3 When the EUT initiates a call . 29g34.5.10.4 Conformance . 29g34.5.11 Distributed Communi
25、cations 29g34.5.11.0 General requirements 29g34.5.11.1 Testing as a PP 29g34.5.11.2 Testing as an RFP . 30g34.5.11.3 Conformance . 30g34.5.12 Higher level modulation options . 30g34.5.12.0 Requirements 30g34.5.12.1 Conformance . 31g35 Testing for compliance with technical requirements 31g35.1 Genera
26、l test requirements . 31g35.1.1 Test philosophy . 31g35.1.2 Test site . 33g35.1.2.1 Open air test site 33g35.1.2.1.1 Description 33g35.1.2.1.2 Calibration . 34g35.1.2.2 Anechoic chamber . 34g35.1.2.2.1 General 34g35.1.2.2.2 Description 34g35.1.2.2.3 Influence of parasitic reflections . 37g35.1.2.2.4
27、 Calibration and mode of use 37g35.1.2.3 Stripline coupler 37g35.1.2.3.0 General 37g35.1.2.3.1 Description 37g35.1.2.3.2 Calibration . 37g35.1.2.3.3 Mode of use . 37g35.1.3 Standard position 38g35.1.4 Test antenna of the LT 38g35.1.5 Substitution antenna 38g35.1.6 Test fixture 38g35.1.6.1 Descriptio
28、n 38g35.1.6.2 Calibration of the test fixture for the measurement of transmitter characteristics . 39g35.1.6.3 Calibration of the test fixture for the measurement of receiver characteristics . 39g35.1.6.4 Mode of use . 40g35.1.7 Equipment with a temporary or internal permanent antenna connector 40g3
29、5.1.7.1 General 40g35.1.7.2 Equipment with a temporary antenna connector . 40g35.1.8 Indoor test site . 41g3ETSI ETSI EN 301 406 V2.2.1 (2016-04) 6 5.1.8.0 General 41g35.1.8.1 Description 41g35.1.8.2 Test for parasitic reflections 41g35.1.8.3 Calibration and mode of use 42g35.1.9 Lower Tester (LT) 4
30、2g35.1.9.1 Description 42g35.1.9.2 Connections between the EUT and the LT . 42g35.1.9.3 Functions and abilities. 42g35.1.9.4 Signal generation uncertainty 43g35.1.9.5 Modulated DECT-like carrier . 43g35.1.9.6 CW interferers . 43g35.1.9.7 DECT RF signal 43g35.1.9.8 Test modulation signals . 43g35.1.1
31、0 Upper Tester (UT) 43g35.1.10.1 Description of the UT 43g35.1.10.2 The test standby mode . 44g35.1.10.3 Test messages 44g35.1.10.4 Dummy setting when EUT is a RFP and it is in test stand-by mode. 44g35.1.11 Description of the lower tester FT and PT 44g35.1.12 General test methods . 45g35.1.12.1 Gen
32、eral 45g35.1.12.2 Sampling the RF signal . 45g35.1.12.2.1 Introduction . 45g35.1.12.2.2 Sampling method . 45g35.1.12.3 Determining the reference position . 45g35.1.12.3.0 General 45g35.1.12.3.1 Case 1: EUTs that cannot transmit 45g35.1.12.3.2 Case 2: EUTs that can transmit . 45g35.1.12.4 Bit error r
33、ate (BER) and Frame Error Ratio (FER) measurements . 45g35.1.13 Test setup 46g35.1.13.1 General 46g35.1.13.2 Test setup 1 . 46g35.1.13.3 Test setup 2 . 46g35.1.13.4 Test setup 3 . 47g35.1.13.5 Test setup 4 . 47g35.1.13.6 Test setup 5 . 47g35.1.14 Test arrangements for intermodulation measurements .
34、48g35.1.14.1 PT to PT arrangement . 48g35.1.14.2 FT to FT arrangement . 48g35.1.14.3 FT to PT arrangement . 49g35.1.15 Test conditions, power supply and ambient temperatures 49g35.1.15.1 General 49g35.1.15.2 Nominal test conditions . 50g35.1.15.3 Extreme test conditions . 50g35.1.15.4 Test power sou
35、rce - general requirements . 51g35.1.15.5 Nominal test power source 52g35.1.15.5.1 Mains voltage 52g35.1.15.5.2 Regulated lead acid battery power sources 52g35.1.15.5.3 Nickel cadmium battery. 52g35.1.15.5.4 Other power sources 52g35.1.15.6 Extreme test power source 52g35.1.15.6.1 Mains voltage 52g3
36、5.1.15.6.2 Regulated lead acid battery power sources 52g35.1.15.6.3 Nickel cadmium battery. 52g35.1.15.6.4 Other power sources 52g35.1.15.7 Testing of host connected equipment and plug-in cards . 52g35.1.15.7.1 Approaches 52g35.1.15.7.2 Alternative A: composite equipment . 53g35.1.15.7.3 Alternative
37、 B: use of a test jig and three hosts 53g35.2 Interpretation of the measurement results 53g35.3 Radio test suites 54g35.3.1 Accuracy and stability of RF carriers . 54g3ETSI ETSI EN 301 406 V2.2.1 (2016-04) 7 5.3.1.1 Test environment . 54g35.3.1.2 Method of measurement 54g35.3.1.3 Verdict criteria wh
38、en the EUT is a RFP 55g35.3.1.4 Verdict criteria when the EUT is a PP 55g35.3.2 Accuracy and stability of timing parameters 55g35.3.2.1 Measurement of packet timing jitter . 55g35.3.2.1.1 Test environment . 55g35.3.2.1.2 Method of measurement 55g35.3.2.1.3 Verdict criteria . 56g35.3.2.2 Measurement
39、of the reference timing accuracy of a RFP . 56g35.3.2.2.1 Test environment . 56g35.3.2.2.2 Method of measurement 56g35.3.2.2.3 Verdict criteria . 56g35.3.2.3 Measurement of packet transmission accuracy of a PP . 57g35.3.2.3.1 Test environment . 57g35.3.2.3.2 Method of measurement 57g35.3.2.3.3 Verdi
40、ct criteria . 57g35.3.3 Transmission burst 58g35.3.3.1 Test environment . 58g35.3.3.2 Method of measurement 58g35.3.3.3 Verdict criteria 58g35.3.4 Transmitted power 59g35.3.4.1 PP and RFP with an integral antenna 59g35.3.4.1.1 Test environment . 59g35.3.4.1.2 Method of measurement 59g35.3.4.1.3 Verd
41、ict criteria for all EUTs 60g35.3.4.2 PP and RFP with external antenna connection(s) 60g35.3.4.2.1 Test environment . 60g35.3.4.2.2 Method of measurement 60g35.3.4.2.3 Verdict criteria for all EUTs 60g35.3.5 RF carrier modulation . 61g35.3.5.1 Test environment . 61g35.3.5.2 Method of measurement, pa
42、rts 1 and 2 . 61g35.3.5.2.1 Introduction . 61g35.3.5.2.2 Part 1 . 61g35.3.5.2.3 Part 2 . 61g35.3.5.3 Method of measurement, parts 3 and 4 . 62g35.3.5.3.0 General 62g35.3.5.3.1 Part 3 . 62g35.3.5.3.2 Part 4 . 62g35.3.5.4 Verdict criteria for part 1 . 62g35.3.5.5 Verdict criteria for part 2 . 62g35.3.
43、5.6 Verdict criteria for part 3 . 63g35.3.5.7 Verdict criteria for part 4 . 63g35.3.6 Unwanted RF power radiation 64g35.3.6.1 General test conditions 64g35.3.6.2 Emissions due to modulation 64g35.3.6.2.1 Test environment . 64g35.3.6.2.2 Method of measurement 64g35.3.6.2.3 Verdict criteria . 65g35.3.
44、6.3 Emissions due to transmitter transients . 66g35.3.6.3.1 Test environment . 66g35.3.6.3.2 Method of measurement 66g35.3.6.3.3 Verdict criteria . 66g35.3.6.4 Emissions due to intermodulation . 67g35.3.6.4.1 Test environment . 67g35.3.6.4.2 Method of measurement 67g35.3.6.4.3 Verdict criteria . 68g
45、35.3.6.5 Spurious emissions when allocated a transmit channel . 68g35.3.6.5.1 Radiated emissions 68g35.3.6.5.2 Conducted spurious emissions when the EUT has a permanent external antenna connector 69g35.3.7 Radio receiver testing . 70g3ETSI ETSI EN 301 406 V2.2.1 (2016-04) 8 5.3.7.1 Radio receiver se
46、nsitivity 70g35.3.7.1.1 Test environment . 70g35.3.7.1.2 Method of measurement 70g35.3.7.1.3 Verdict criteria . 71g35.3.7.2 Radio receiver reference BER and FER 71g35.3.7.2.1 Test environment . 71g35.3.7.2.2 Method of measurement 71g35.3.7.2.3 Verdict criteria . 71g35.3.7.3 Radio receiver interferen
47、ce performance 71g35.3.7.3.1 Test environment . 71g35.3.7.3.2 Method of measurement 71g35.3.7.3.3 Verdict criteria . 72g35.3.7.4 Radio receiver blocking case 1: owing to signals occurring at the same time but on other frequencies 72g35.3.7.4.1 Test environment . 72g35.3.7.4.2 Method of measurement 7
48、2g35.3.7.4.3 Verdict criteria . 73g35.3.7.5 Radio receiver blocking case 2: owing to signals occurring at a different time 74g35.3.7.5.1 Test environment . 74g35.3.7.5.2 Method of measurement 74g35.3.7.5.3 Verdict criteria . 74g35.3.7.6 Receiver intermodulation performance . 74g35.3.7.6.1 Test envir
49、onment . 74g35.3.7.6.2 Method of measurement 75g35.3.7.6.3 Verdict criteria . 75g35.3.7.7 Spurious emissions when the PP has no allocated transmit channel . 75g35.3.7.7.1 Test environment. 75g35.3.7.7.2 Method of measurement 75g35.3.7.7.3 Verdict criteria (outside the DECT band) 76g35.3.7.7.4 Verdict criteria (inside the DECT band) 76g35.3.8 Channel access 76g35.3.9 WRS testing 76g35.3.9.0 General 76g35.3.9.1 Testing as a PP 76g35.3.9.2 Testing as an RFP . 76g35.3.9.3 Additional requirements 77g35.3.10 Requirements for PPs with direct PP to PP communication mode . 77g35.3.10.0
