1、 ETSI EN 301 526 V1.1.1 (2006-07)Harmonized European Standard (Telecommunications series) Electromagnetic compatibilityand Radio spectrum Matters (ERM);Harmonized EN for CDMA spread spectrum mobile stationsoperating in the 450 MHz cellular band (CDMA 450)and 410, 450 and 870 MHz PAMR bands (CDMA-PAM
2、R)covering essential requirementsof article 3.2 of the R Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the E
3、TSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Forewo
4、rd This Harmonized European Standard (Telecommunications series) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present document has been produced by ETSI in response to a mandate from the European Commission issued under Council Dir
5、ective 98/34/EC (as amended) laying down a procedure for the provision of information in the field of technical standards and regulations. The present document is intended to become a Harmonized Standard, the reference of which will be published in the Official Journal of the European Communities re
6、ferencing the Directive 1999/5/EC 1 of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual recognition of their conformity (“the R or - under article 3.3 should the Commission take the necessary decisions; without req
7、uiring alteration of standards that are already published. It clarifies, simplifies and promotes the usage of Harmonized Standards as the relevant means of conformity assessment. ETSI ETSI EN 301 526 V1.1.1 (2006-07) 9 1 Scope The present document applies to cdma450 mobile stations using CDMA 1x spr
8、ead spectrum technology, i.e. Band Class 5 equipment or Band Class 11 equipment as defined in TIA-1030 19, capable of operating in all or any part of the frequency bands defined in footnote EU34 from the European Common Allocation table ERC Report 25 14: “Parts of the bands 450 to 457,5 / 460 to 467
9、,5 MHz may also be used for existing and evolving public cellular networks on a National basis“. The present document also applies to CDMA-PAMR mobile stations covering, in accordance with ECC Decision ECC DEC(04)06 12, the frequency bands: Band Class 11: 410 MHz to 430 MHz and 450 MHz to 470 MHz wi
10、th 10 MHz duplex spacing between the transmit frequencies of mobile stations (410 MHz to 420 MHz and 450 MHz to 460 MHz) and the transmit frequencies of base stations (420 MHz to 430 MHz and 460 MHz to 470 MHz). Band Class 12: 870 MHz to 876 MHz paired with 915 MHz to 921 MHz with 45 MHz duplex spac
11、ing between the transmit frequencies of mobile stations (870 MHz to 876 MHz) and the transmit frequencies of base stations (915 MHz to 921 MHz). The present document is intended to cover the provisions of Directive 1999/5/EC 1 (R ElectroMagnetic Compatibility (EMC) standard for radio equipment and s
12、ervices“. 7 TIA/EIA/IS-2000.5-C (2002): “Upper Layer (Layer 3) Signaling Standard for cdma2000 Spread Spectrum Systems - Release C“. 8 TIA/EIA/IS-856-1 (2002): “cdma2000 High Rate Packet Data Air Interface Specification - Addendum 1“. 9 TIA-866 (2002): “Recommended Minimum Performance Standards for
13、cdma2000 High Rate Packet Data Access Terminal“. 10 TIA/EIA/IS-890 (2001): “Test Application Specification (TAS) for High Rate Packet Data Air Interface“. 11 ITU-R Recommendation SM.329-10 (2003): “Unwanted emissions in the spurious domain“. 12 ECC Decision (04)06: “ECC Decision of 19 March 2004 on
14、the availability of frequency bands for the introduction of Wide Band Digital Land Mobile PMR/PAMR in the 400 MHz and 800/900 MHz bands“. 13 CEPT/ERC/Recommendation 74-01E (Sifok 1998, Nice 1999, Sesimbra 2002): “Unwanted emissions in the spurious domain“. 14 ERC Report 25 (Lisboa January 2002 - Dub
15、lin 2003 - Turkey 2004 - Copenhagen 2004): “The European table of frequency allocations and utilisations covering the frequency range 9 kHz to 275 GHz“. 15 ECC Report 38,Granada, February 2004: “The technical impact of introducing CDMA/PAMR on the UIC DMO Uncertainties in the measurement of mobile r
16、adio equipment characteristics“. 19 TIA 1030 (2004): “Band Class Specification for cdma2000 Spread Spectrum Systems“. 3 Definitions, symbols and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the R for the reverse CDMA channel, there is one
17、 RF carrier. ETSI ETSI EN 301 526 V1.1.1 (2006-07) 15soft handoff: handoff occurring while the mobile station is in the mobile station control on the traffic channel state NOTE: This handoff is characterized by commencing communications with a new base station on the same CDMA frequency assignment b
18、efore terminating communications with the old base station (see hard handoff). spreading rate: PN chip rate of the forward CDMA channel or the reverse CDMA channel, defined as a multiple of 1,2288 Mcps spreading rate 1: spreading rate 1 is often referred to as “1x“ NOTE: A spreading rate 1 forward C
19、DMA channel uses a single direct-sequence spread carrier with a chip rate of 1,2288 Mcps a spreading rate 1 reverse CDMA channel uses a single direct-sequence spread carrier with a chip rate of 1,2288 Mcps. spurious emissions: As defined by ITU-R recommendation SM.329-10 11. sync channel: code chann
20、el 32 in the forward CDMA channel, which transports the synchronization message to the mobile station traffic channel: communication path between a mobile station and a base station used for user and signalling traffic NOTE: The term traffic channel implies a forward traffic channel and reverse traf
21、fic channel pair (see also forward traffic channel and reverse traffic channel). Walsh function: one of 2Ntime orthogonal binary functions NOTE: The functions are orthogonal after mapping “0“ to 1 and “1“ to -1. 3.2 Symbols For the purposes of the present document, the following symbols apply:dBc ra
22、tio (in dB) of the sideband power of a signal, measured in a given bandwidth at a given frequency offset from the centre frequency of the same signal, to the total inband power of the signal NOTE: For CDMA, the total inband power of the signal is measured in a 1,23 MHz bandwidth around the centre fr
23、equency of the CDMA signal for a spreading rate 1 CDMA signal. dBm measure of power expressed in terms of its ratio (in dB) to one milliwatt dBm/Hz measure of power spectral density NOTE: The ratio, dBm/Hz, is the power in one hertz of bandwidth, where power is expressed in units of dBm. dBW measure
24、 of power expressed in terms of its ratio (in dB) to one watt kHz kiloHertz (103Hertz) mbar millibar (10-3Bar) Mcps Megachips per second (106chips per second) MHz MegaHertz (106Hertz) NFTCMPRestartTxprotocol numeric constant that is the number of consecutive slots of non-null rate DRCs to re-enable
25、the reverse traffic channel transmitter once it is disabled due to DRC supervision failure and equals 12 as defined in TIA/EIA/IS-890 10, clause 8.4.8 s microsecond (10-6second) ms illisecond (10-3second) ns nanosecond (10-9second) Pa Pascal TFTCMDRCSupervisionprotocol numeric constant equal to 240
26、ms as defined in TIA/EIA/IS-890 10 at clause 8.4.8 TFTCMPRestartTxprotocol numeric constant equal to 12 control channel cycles as defined in TIA/EIA/IS-890 10 at clause 8.4.8 ETSI ETSI EN 301 526 V1.1.1 (2006-07) 16TCCMPSupervisionprotocol numeric constant equal to 12 control channel cycles as defin
27、ed in TIA/EIA/IS-890 10 at clause 8.2.8 3.3 Abbreviations For the purposes of the present document, the following abbreviations apply: CDMA Code Division Multiple Access CW Continuous Wave DCCH Dedicated Control CHannel DRC Data Rate Control DTX Discontinuous Transmission e.i.r.p. equivalent isotrop
28、ically radiated power e.r.p. effective radiated power EMC ElectroMagnetic Compatibility EUT Equipment Under Test FCS Frame Check Sequence FER Frame Error Rate GPS Global Positioning System HRPD High Rate Packet Data HS-RTT HS Requirements and Test specifications Table LV Low Voltage MS Mobile Statio
29、nPAMR Public Access Mobile Radio PER Packet Error Rate NOTE: PER = 1- ted transmitpackets ofNumber received packets good ofNumber PN Pseudorandom Noise PPP Point-to-Point Protocol PUF Power Up Function R -36 dBm/10 kHz; -36 dBm/100 kHz; -30 dBm/1 MHz; 9 kHz 10,0 MHz -36 dBm/1 kHz -36 dBm/10 kHz -36
30、dBm/100 kHz -30 dBm/1 MHz 9 kHz f 150 kHz 150 kHz f 30 MHz 30 MHz f 1 GHz 1 GHz f 12,75 GHz NOTE: All frequencies in the measurement bandwidth shall satisfy the restrictions on |f| where f = centre frequency - closer measurement edge frequency (f). f is positive offset from the highest valid CDMA ch
31、annel in the band subclass or negative offset from the lowest valid CDMA channel in the band subclass. The closer edge frequency (f) of the measurement filter is the -3 dB point of the measurement filter closest to the carrier frequency. 4.2.2.3 Conformance Conformance tests described in clause 5.3.
32、1 shall be carried out. 4.2.3 Maximum RF output power 4.2.3.1 Definition For each reverse traffic channel radio configuration that the mobile station supports the maximum radiated RF output power is determined by the measurement of the maximum power that the mobile station transmits as measured at t
33、he mobile station antenna connector plus the antenna gain recommended by the mobile station manufacturer. The antenna gain is determined by using the Radiated Signal Measurement Procedures (see ANSI/TIA-98-F 4, clause 2.6) and calculating the antenna gain for e.i.r.p. or e.r.p. as appropriate. 4.2.3
34、.2 Limits For each radio configuration that the mobile station operating in a 1x and/or HRPD system supports, the maximum output power of each mobile station class shall be such that the maximum radiated power for the mobile station class using the antenna gain recommended by the mobile station manu
35、facturer is within the limits specified in table 5 or 6. ETSI ETSI EN 301 526 V1.1.1 (2006-07) 19When the mobile station is transmitting using one of the test mode channel configurations specified in table 4, the maximum output power requirements of the mobile station specified in tables 5 and 6 may
36、 be reduced by the applicable output power backoff allowance specified in table 4. Table 4: Maximum output power backoff allowances Test mode Configuration Output Power Reduction R-PICH + R-DCCH 2,5 dB R-PICH + R-DCCH + R-FCH (1 500 bit/s) 2,0 dB R-PICH + R-FCH (9 600 bit/s) + R-SCH0 (9 600 bit/s) 2
37、,0 dB R-PICH + R-DCCH + R-SCH0 (9 600 bit/s) 1,5 dB 4.2.3.2.1 Limits for Band Classes 5 and 11 mobile stations Table 5: Effective radiated power at maximum output power for Band Classes 5 and 11 Mobile station power class as specified in ANSI/TIA-98-F 4 Radiating measurement Lower limit Upper limit
38、I e.i.r.p. 30 dBm (1,25 W) 38 dBm (6,3 W) II e.i.r.p. 27 dBm (0,5 W) 34 dBm (2,5 W) III e.i.r.p. 23 dBm (0,2 W) 27 dBm (1,0 W) 4.2.3.2.2 Limits for Band Class 12 mobile stations Table 6: Effective radiated power at maximum output power for Band Class 12 Mobile station power class as specified in ANS
39、I/TIA-98-F 4 Radiating measurement Lower limit Upper limit I e.i.r.p. 33 dBm (2,0 W) 40 dBm (10 W) II e.i.r.p. 28 dBm (0,63 W) 35 dBm (3,2 W) III e.i.r.p. 23 dBm (0,2 W) 30 dBm (1,0 W) IV e.i.r.p. 18 dBm ( 63 mW) 25 dBm (0,32 W) NOTE: CEPT compatibility studies for CDMA-PAMR in ECC Reports 38 15, 39
40、 16 and 41 17 were carried out for class II/III equipment. 4.2.3.3 Conformance Conformance tests described in clause 5.3.2 shall be carried out. 4.2.4 Radiated spurious unwanted emissions 4.2.4.1 Definition The radiated unwanted emissions are radiated emissions from the enclosure port (cabinet radia
41、tion) excluding the intentional emission from the transmitter. This test is applicable to the mobile station and ancillary equipment. 4.2.4.2 Limits The frequency boundary and reference bandwidths for the detailed transitions of the limits between the requirements for out of band emissions and spuri
42、ous emissions are based on CEPT/ERC Recommendation 74-01E 13. ETSI ETSI EN 301 526 V1.1.1 (2006-07) 20The requirements shown in table 6 are only applicable for frequencies in the spurious domain. The mobile station emissions shall not exceed the limits given in table 7. Table 7: Radiated unwanted em
43、issions requirements Frequency Limit (e.r.p.)/ reference bandwidth idle mode Limit (e.r.p.)/ reference bandwidth traffic mode 30 MHz f 1 000 MHz -57 dBm/100 kHz -36 dBm/100 kHz 1 GHz f 12,75 GHz -47 dBm/1 MHz -30 dBm/1 MHz fc - 4 MHz f fc + 4 MHz No requirement No requirement NOTE: fc is the nominal
44、 MS transmit centre frequency. 4.2.4.3 Conformance Conformance tests described in clause 5.3.3 shall be carried out. 4.2.5 Minimum controlled output power 4.2.5.1 Definition The minimum controlled output power of the mobile station is the output power, measured at the mobile station antenna connecto
45、r, when both closed loop and open loop power control require the MS to transmit at its minimum output. 4.2.5.2 Limits With both closed loop and open loop power control set to minimum, the mean output power of the mobile station shall be less than -50 dBm/1,23 MHz, centred at the CDMA Channel. 4.2.5.
46、3 Conformance Conformance tests described in clause 5.3.4 shall be carried out. 4.2.6 Control and monitoring function 4.2.6.1 Definition This requirement, together with other control and monitoring technical requirements identified in table 1, the table of cross references, , verifies that the contr
47、ol and monitoring functions of the MS prevent it from transmitting in the absence of a valid network. 4.2.6.2 Limits The maximum measured power during the duration of the test shall not exceed -30 dBm. 4.2.6.3 Conformance Conformance tests described in clause 5.3.5 shall be carried out. ETSI ETSI EN
48、 301 526 V1.1.1 (2006-07) 214.2.7 Supervision of Paging Channel or Forward Common Control Channel 4.2.7.1 Definition Applicable to mobile station operating in 1x systems. These requirements verify mobile station supervision when in the System Access State, where the mobile station shall monitor the
49、Paging Channel or Forward Common Control Channel at all times per clause 2.6.3.1.8 of TIA/EIA/IS-2000.5-C 7. 4.2.7.2 Limits The mobile station shall set a timer for 0.92 second whenever a valid message is received on the Paging Channel or Forward Common Control Channel, whether addressed to the mobile station or not. For testing this requirement, no valid messages are sent after disabling of the Paging Channel or Forward Common Control Channel. For Test 2 as defined in the tests referenced in clause 5.3.6, the Broadcast Co
