1、 ETSI EN 301 908-22 V6.1.1 (2016-07) IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 22: OFDMA TDD WMAN (Mobile WiMAXTM) FDD Base Stations (BS) HARMONISED EUROPEAN STANDARD ETSI ETSI EN 301 908-22 V6.1.1 (2016-07)2 Refer
2、ence REN/MSG-TFES-11-22-RED Keywords 3G, cell, digital, FDD, IMT, IMT-2000, mobile, radio, regulation, WiMAX ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistr
3、e la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present documen
4、t shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within
5、ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present
6、document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized b
7、y written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTST
8、M, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ET
9、SI ETSI EN 301 908-22 V6.1.1 (2016-07)3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 6g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitions, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbol
10、s 9g33.3 Abbreviations . 10g34 Technical requirements specification . 10g34.1 Environmental profile . 10g34.2 Conformance requirements 10g34.2.1 Introduction. 10g34.2.2 Spectrum emission mask 11g34.2.2.1 Definition 11g34.2.2.2 Limits 11g34.2.2.2.1 Requirements for 5 MHz channel bandwidth 11g34.2.2.2
11、.2 Requirements for 10 MHz channel bandwidth 11g34.2.2.3 Conformance . 12g34.2.3 Transmitter Adjacent Channel Leakage power Ratio (ACLR) . 12g34.2.3.1 Definition 12g34.2.3.2 Limits 12g34.2.3.2.1 ACLR requirements for 5 MHz channel bandwidth 12g34.2.3.2.2 ACLR requirements for 10 MHz channel bandwidt
12、h 12g34.2.3.3 Conformance . 12g34.2.4 Transmitter spurious emissions . 13g34.2.4.1 Definition 13g34.2.4.2 Limits 13g34.2.4.2.0 General requirements . 13g34.2.4.2.1 Requirements for 5 MHz channel bandwidth 13g34.2.4.2.2 Requirements for 10 MHz channel bandwidth 13g34.2.4.2.3 Additional Spurious Emiss
13、ion Requirements 14g34.2.4.2.4 Protection of the BS receiver of own or different BS 14g34.2.4.3 Conformance . 14g34.2.5 Base station maximum output power 14g34.2.5.1 Definition 14g34.2.5.2 Limits 14g34.2.5.3 Conformance . 15g34.2.6 Transmitter Intermodulation . 15g34.2.6.1 Definition 15g34.2.6.2 Lim
14、its 15g34.2.6.3 Conformance . 15g34.2.7 Receiver spurious emissions . 15g34.2.7.1 Definition 15g34.2.7.2 Limits 15g34.2.7.3 Conformance . 16g34.2.8 Receiver Adjacent Channel Selectivity (ACS) . 16g34.2.8.1 Definition 16g34.2.8.2 Limits 16g34.2.8.3 Conformance . 16g34.2.9 Receiver blocking characteri
15、stics . 17g3ETSI ETSI EN 301 908-22 V6.1.1 (2016-07)4 4.2.9.1 Definition 17g34.2.9.2 Limits 17g34.2.9.3 Conformance . 18g34.2.10 Receiver intermodulation characteristics 18g34.2.10.1 Definition and applicability . 18g34.2.10.2 Limits 18g34.2.10.3 Conformance . 19g34.2.11 Receiver reference sensitivi
16、ty level 19g34.2.11.1 Definition 19g34.2.11.2 Limits 19g35 Testing for compliance with technical requirements 19g35.1 Environmental conditions for testing . 19g35.2 Product information 20g35.3 Interpretation of the measurement results 20g35.4 Essential radio test suites 21g35.4.1 Transmitter Spectru
17、m Emission Mask 21g35.4.1.1 Method of measurement 21g35.4.1.1.1 Initial conditions 22g35.4.1.1.2 Procedure . 22g35.4.1.2 Test requirements 22g35.4.2 Transmitter Adjacent Channel Leakage Power Ratio . 23g35.4.2.1 Method of measurement 23g35.4.2.1.1 Initial conditions 23g35.4.2.1.2 Procedure . 23g35.4
18、.2.2 Test requirements 24g35.4.3 Transmitter spurious emissions . 24g35.4.3.1 Method of measurement 24g35.4.3.1.1 Initial conditions 25g35.4.3.1.2 Procedure . 25g35.4.3.2 Test requirements 25g35.4.4 Base Station maximum output power . 25g35.4.4.1 Method of measurement 26g35.4.4.1.1 Initial condition
19、s 26g35.4.4.1.2 Procedure . 26g35.4.4.2 Test requirements 26g35.4.5 Transmitter Intermodulation . 27g35.4.5.1 Method of measurement 27g35.4.5.1.1 Initial conditions 27g35.4.5.1.2 Procedure . 27g35.4.5.2 Test requirements 27g35.4.6 Receiver spurious emissions . 28g35.4.6.1 Method of measurement 28g35
20、.4.6.1.1 Initial conditions 28g35.4.6.1.2 Procedure . 28g35.4.6.2 Test requirements 29g35.4.7 Receiver Adjacent Channel Selectivity (ACS) . 29g35.4.7.1 Method of measurement 29g35.4.7.1.1 Initial conditions 29g35.4.7.1.2 Procedure . 29g35.4.7.2 Test requirements 30g35.4.8 Receiver blocking character
21、istics . 30g35.4.8.1 Method of measurement 30g35.4.8.1.1 Initial conditions 31g35.4.8.1.2 Procedure . 31g35.4.8.2 Test requirements 31g35.4.9 Receiver intermodulation characteristics 31g35.4.9.1 Method of measurement 32g35.4.9.1.1 Initial conditions 32g35.4.9.1.2 Procedure . 32g35.4.9.2 Test require
22、ments 33g35.4.10 Receiver reference sensitivity level 33g3ETSI ETSI EN 301 908-22 V6.1.1 (2016-07)5 5.4.10.1 Method of test . 33g35.4.10.2 Test requirement . 33g3Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 34g3Annex B (norma
23、tive): Environmental profile specification . 35g3Annex C (informative): Void . 36g3Annex D (informative): Bibliography . 37g3History 38g3ETSI ETSI EN 301 908-22 V6.1.1 (2016-07)6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ET
24、SI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is availa
25、ble from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 00
26、0 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Harmonised European Standard (EN) has been produced by ETSI Technical Committee Mobile Standards Group (MSG). The present document has been prepared under the Commissio
27、ns standardisation request C(2015) 5376 final i.7 to provide one voluntary means of conforming to the essential requirements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/
28、EC i.2. Once the present document is cited in the Official Journal of the European Union under that Directive, compliance with the normative clauses of the present document given in table A-1 confers, within the limits of the scope of the present document, a presumption of conformity with the corres
29、ponding essential requirements of that Directive, and associated EFTA regulations. The present document is part 22 of a multi-part deliverable. Full details of the entire series can be found in part 1 i.8. National transposition dates Date of adoption of this EN: 12 July 2016 Date of latest announce
30、ment of this EN (doa): 31 October 2016 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 April 2017 Date of withdrawal of any conflicting National Standard (dow): 30 April 2018 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “sh
31、ould not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introducti
32、on The present document is part of a set of standards developed by ETSI that are designed to fit in a modular structure to cover radio equipment within the scope of the Radio Equipment Directive i.2. The present document is produced following the guidance in ETSI EG 203 336 i.3 as applicable. ETSI E
33、TSI EN 301 908-22 V6.1.1 (2016-07)7 1 Scope The present document applies to the following radio equipment type: Mobile WiMAXTMFDD Base Stations for IMTOFDMA TDD WMAN This radio equipment type is capable of operating in all or any part of the frequency bands given in table 1-1. Table 1-1: Base Statio
34、n WiMAXTMFDD Operating frequency bands Mobile WiMAXTMBand Class Index Direction of transmission Mobile WiMAXTMFDD frequency bands 7G Transmit 925 MHz to 960 MHz Receive 880 MHz to 915 MHz 6C Transmit 1 805 MHz to 1 880 MHz Receive 1 710 MHz to 1 785 MHz The present document contains requirements to
35、demonstrate that Radio equipment both effectively uses and supports the efficient use of radio spectrum in order to avoid harmful interference. In addition to the present document, other ENs that specify technical requirements in respect of essential requirements under other parts of article 3 of th
36、e Radio Equipment Directive 2014/53/EU i.2 may apply to equipment within the scope of the present document. NOTE: A list of such ENs is included on the web site http:/www.newapproach.org. 2 References 2.1 Normative references References are either specific (identified by date of publication and/or e
37、dition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced documents which are not found to be publicly available in the expected
38、location might be found at http:/docbox.etsi.org/Reference. NOTE: While any hyperlinks included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 WMF-T25
39、-002-R010v06 (2012): “WiMAX Forum Test Procedures - Mobile Radio Conformance Tests“ - Release 1 v06. 2 CEPT/ERC/Recommendation 74-01E (Sifok 98, Nice 99, Sesimbra 02, Hradec Kralove 05, Cardiff 11) (01-2011): “Unwanted emissions in the spurious domain“. 2.2 Informative references References are eith
40、er specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks
41、included in this clause were valid at the time of publication ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. ETSI ETSI EN 301 908-22 V6
42、.1.1 (2016-07)8 i.1 Recommendation ITU-R SM.329-12 (2012): “Unwanted emissions in the spurious domain“. i.2 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radi
43、o equipment and repealing Directive 1999/5/EC Text with EEA relevance. i.3 ETSI EG 203 336: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive
44、 2014/53/EU“. i.4 ETSI TR 102 215 (V1.3.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Recommended approach, and possible limits for measurement uncertainty for the measurement of radiated electromagnetic fields above 1 GHz“. i.5 ETSI EN 300 019-1-0: “Environmental Engineering
45、(EE); Environmental conditions and environmental tests for telecommunications equipment; Part 1-0: Classification of environmental conditions; Introduction“. i.6 ETSI TR 100 028 (V1.4.1) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of
46、 mobile radio equipment characteristics“. i.7 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support o
47、f Directive 2014/53/EU of the European Parliament and of the Council. i.8 ETSI EN 301 908-1 (V11.1.1): “IMT cellular networks; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU; Part 1: Introduction and common requirements“. 3 Definitions, symbols and
48、 abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in the Radio Equipment Directive 2014/53/EU i.2 and the following apply: burst: period during which radio waves are intentionally transmitted, preceded and succeeded by periods during which no in
49、tentional transmission is made environmental profile: declared range of environmental conditions under which equipment within the scope of the present document is required to be compliant Eval_BW1: test condition where the pass band of a rectangular filter with a bandwidth of 4,75 MHz for 5 MHz equipment and 9,5 MHz for 10 MHz equipment is used for measurement centred on an operating channel or a victim channel integral antenna: antenna which is declared to be part of the radio equipment by the manufacturer NOTE: Even when equipment wit
