1、 ETSI EN 305 200-2-2 V1.2.1 (2018-08) Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 2: Fixed broadband access networks EUROPEAN STANDARD ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)2 Referenc
2、e REN/ATTM-006 Keywords broadband, energy management, ICT, sustainability ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06)
3、N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the
4、 prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the pres
5、ent document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment
6、to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The c
7、ontent of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2018. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are trademarks of ETSI registered for the benefit o
8、f its Members. 3GPPTM and LTETMare trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSMand the GSM logo are trademarks registered and owned by the GSM Association. ETSI ETSI EN 305 200-2-2 V
9、1.2.1 (2018-08)3 Contents Intellectual Property Rights 6g3Foreword . 6g3Modal verbs terminology 7g3Introduction 7g31 Scope 9g32 References 9g32.1 Normative references . 9g32.2 Informative references 9g33 Definitions, symbols and abbreviations . 10g33.1 Definitions 10g33.2 Symbols 11g33.3 Abbreviatio
10、ns . 12g34 Energy management of fixed access networks (FANs) . 12g34.1 General . 12g34.1.1 Fixed (broadband) access networks (FANs) . 12g34.1.2 Fixed access network (FAN) implementations . 13g34.1.3 Measured energy . 14g34.1.4 Energy consumption . 14g34.1.5 Task Effectiveness 15g35 Global KPI (KPIEM
11、) for fixed access networks (FANs) . 16g35.1 General . 16g35.1.1 Global KPI (KPIEM) for fixed access networks (FANs) 16g35.1.2 Objective KPIs 16g35.1.2.1 Energy consumption (KPIEC) 16g35.1.2.1.1 General 16g35.1.2.2 Task effectiveness (KPITE) 16g35.1.2.2.1 General 16g35.1.2.3 Energy re-use (KPIREUSE)
12、 17g35.1.2.4 Renewable energy (KPIREN) 17g35.2 Scale . 17g35.3 Utilization and evolution 17g35.4 Definition of boundaries . 18g35.5 Formulae. 18g35.5.1 Global KPI (KPIEM) for fixed access networks (FANs) 18g35.5.1.1 General 18g35.5.1.2 Definition of terms 18g35.5.1.3 Clarity . 18g35.5.1.4 Criteria 1
13、8g35.5.2 Objective KPIs for fixed access networks (FANs) . 19g35.5.2.1 Energy consumption (KPIEC) 19g35.5.2.1.1 Formula . 19g35.5.2.1.2 Definitions of terms . 19g35.5.2.1.3 Clarity 20g35.5.2.1.4 Criteria. 20g35.5.2.2 Task Effectiveness (KPITE) . 20g35.5.2.2.1 Formula . 20g35.5.2.2.2 Definitions of t
14、erms . 20g35.5.2.2.3 Clarity 20g35.5.2.2.4 Criteria. 20g35.5.2.3 Renewable energy (KPIREN) 21g35.5.2.3.1 Formula . 21g35.5.2.3.2 Definitions of terms . 21g35.5.2.3.3 Clarity 21g3ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)4 5.5.2.3.4 Criteria . 21g35.6 Measurement points and procedures 21g35.6.1 Object
15、ive KPIs for FANs 21g35.6.1.1 Energy consumption (KPIEC) 21g35.6.1.1.1 Measurement points . 21g35.6.1.1.2 Measurement procedures . 22g35.6.1.2 Task effectiveness (KPITE) 22g35.6.1.2.1 Measurement points . 22g35.6.1.2.2 Measurement procedures . 23g35.6.1.3 Renewable energy (KPIREN) 23g35.6.1.3.1 Meas
16、urement points . 23g35.6.1.3.2 Measurement procedures . 23g35.7 Reporting 23g3Annex A (informative): History of network schematics 25g3Annex B (normative): Estimating data volumes . 26g3History 28g3ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)5 List of figures Figure 1: Updated schematic of fixed and mo
17、bile communication networks .13g3Figure 2: Fixed access network implementations 14g3Figure 3: Schematic of FAN energy consumption 15g3Figure 4: Schematic of measurements points for data_volume .23g3Figure A.1: Schematic of fixed and mobile communication networks (June 2011) 25g3ETSI ETSI EN 305 200-
18、2-2 V1.2.1 (2018-08)6 Intellectual Property Rights Essential patents IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
19、in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Polic
20、y, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The pres
21、ent document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those tr
22、ademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword This European Standard (EN) has been produced by ETSI Technical Committee Access, Terminals, Transmission and Multiplexing (ATTM). The present
23、 document is part 2, sub-part 2 of a multi-part deliverable covering Global Key Performance Indicators for energy management of operational broadband deployment infrastructures as identified below: Part 1: “General requirements“; Part 2: “Specific requirements“; Sub-part 1: “ICT Sites“; Sub-part 2:
24、“Fixed broadband access networks“; Sub-part 3: “Mobile broadband access networks“; Part 3: “ICT Sites“; Part 4: “Design assessments“. National transposition dates Date of adoption of this EN: 23 July 2018 Date of latest announcement of this EN (doa): 31 October 2018 Date of latest publication of new
25、 National Standard or endorsement of this EN (dop/e): 30 April 2019 Date of withdrawal of any conflicting National Standard (dow): 30 April 2019 ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)7 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“,
26、 “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction Energy costs continue to r
27、ise, a trend that will continue in the future, while broadband penetration is introducing new active equipment to the network architecture. In this context, and to reflect other environmental aspects of sustainability, it is vital that the main telecommunication operators implement effective general
28、 engineering of fixed and mobile broadband networks and sites provisioning, managing or using those networks (i.e. ICT sites) in order to respond to critical issues of energy consumption while proposing essential solutions to broadband deployment. To guide this process, it is essential that metrics
29、are defined, termed Global Key Performance Indicators (KPIs), that enable energy usage to be managed more effectively. The Global Key Performance Indicators of the ETSI EN 305 200 i.1 series address operational infrastructures and do not consider design or operation of individual components comprisi
30、ng those infrastructures. The ETSI EN 305 200 i.1 series of standards comprises: ETSI EN 305 200-1 i.2: a generic requirements document addressing Global KPIs for operational infrastructures; a sub-series ETSI EN 305 200-2 that defines the Global KPIs, and drives energy management targets, for speci
31、fic operational networks and sites and which describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives): - ETSI EN 305 200-2-1 i.3: ICT Sites; - ETSI EN 305 200-2-2: Fixed broadband access networks; NOTE: Excluding cable access networks. - ETSI EN 305
32、 200-2-3 i.4: Mobile broadband access networks; The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain information on values that have been used by certain organizations. a sub-series ETSI EN 305 200-3 i.5 including ETSI EN 305 200-3-1 i.6 that
33、defines particular implementations of Global KPIs within ICT sites based on the requirements of ETSI EN 305 200-2-1 i.3, and which may define levels of performance to simplify and provide clearer understanding of Global KPIs allowing the evaluation of performance of energy use management in ICT site
34、s. The standards do not define weightings of Objective KPIs or targets or limits for Global KPIs but may contain information on values that have been used by certain organizations. a sub-series ETSI EN 305 200-4 including ETSI EN 305 200-4-4 i.7 that defines design assessments of Global KPIs, and dr
35、ives energy management targets, for specific operational networks and sites and which describes how the Global KPIs are to be applied (which may be used to support future regulatory objectives). These standards may be considered to be a contribution to the application of ISO 50001 i.8 in relation to
36、 the development of policy for the continuous improvement of energy management and will accelerate: the availability of operational infrastructure architectures and network implementations that use energy more efficiently; the definition and attainment objectives for other environmental aspects of s
37、ustainability for operational broadband networks. ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)8 The present document specifies the requirements for a Global KPI for energy management (KPIEM) and their underpinning Objective KPIs for the fixed access networks (FANs) of broadband deployment. The requirem
38、ents are mapped to the general requirements of ETSI EN 305 200-1 i.2. ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)9 1 Scope The present document specifies the requirements for a Global KPI for energy management (KPIEM) and their underpinning Objective KPIs addressing the following objectives for the fi
39、xed access networks (FANs) of broadband deployment: energy consumption; task effectiveness; renewable energy. The requirements are mapped to the general requirements of ETSI EN 305 200-1 i.2. Energy management of fixed access networks comprises a number of independent layers. The present document ad
40、dresses performance of infrastructures that supports the normal function of hosted ICT equipment within the fixed access network (e.g. power distribution, environmental control, security and safety).The present document does not address other layers such as performance of ICT equipment itself, perfo
41、rmance of usage of available processing power, and layers related to final service delivered (e.g. processing power required per itemized outcome) or overlay layers (e.g. energy consumption required per itemized outcome). The environmental impact and management of different energy sources are outsid
42、e the scope of the present document. Within the present document: clause 4 describes the energy parameters for FANs together with inclusions/exclusions of different energy contributions; clause 5 specifies the requirements for measurement, calculation, classification and reporting of KPIEM. 2 Refere
43、nces 2.1 Normative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any
44、 amendments) applies. Referenced documents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validi
45、ty. The following referenced documents are necessary for the application of the present document. Not applicable. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the c
46、ited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced docu
47、ments are not necessary for the application of the present document but they assist the user with regard to a particular subject area. ETSI ETSI EN 305 200-2-2 V1.2.1 (2018-08)10 i.1 ETSI EN 305 200 series: “Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infr
48、astructures; Global KPIs“. i.2 ETSI EN 305 200-1: “Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 1: General requirements“. i.3 ETSI EN 305 200-2-1: “Access, Terminals, Transmission and Multiplexing (ATTM); Energy management
49、; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 1: ICT Sites“. i.4 ETSI EN 305 200-2-3: “Access, Terminals, Transmission and Multiplexing (ATTM); Energy management; Operational infrastructures; Global KPIs; Part 2: Specific requirements; Sub-part 3: Mobile broadband access networks“. i.5 ETSI EN 305 200-3 series: “Energy management: Operational infrastructures: Global KPIs - Part 3: ICT Sites“. i.6 ETSI EN 305 200-3-1: “Access, Terminals, Transmission and Multiplexing (ATTM); Energy m
