1、ETSI GSM*04-13 96 3400855 OLObObO bbb GSM 1 ELECOMMUNICATION STANDARD GSM 04.13 May 1996 Version 5.0.0 * Source: ETSI TC-SMG _ - Refe re nce: TSIS MG -0304 1 3Q ICs: 33.060.50 Key words: Digital cellular telecommunications system, Global System for Mobile communications (GSM) GLOBAL SYSTEM FOR MOBIL
2、E COMMUNICATIONS Digital cellular telecommunications system (Phase 2+); Performance requirements on the mobile radio interface (GSM 04.13) ETSI European Telecommunications Standards Institute ETSI Secretariat Postal address: F-O6921 Sophia Antipolis CEDEX - FRANCE -Office address: 650 Route des Luci
3、oles - Sophia Antipolis - Valbonne - FRANCE X.400: c=fr, a=atlas, p=etsi, s=cecretariat - Internet: secretariat etsi.fr Tel.: +33 92 94 42 O0 - Fax: +33 93 65 47 16 Copyright Notification: No part may be reproduced except as authorized by written permission. The copyright and the foregoing restricti
4、on extend to reproduction in all media. O European Telecommunications Standards Institute i 996. All rights reserved. ETSI GSM*04.L3 36 m 3400855 OLObObL 5T2 W Page 2 GSM 04.13 Version 5.0.0: May 1996 Whilst every care has been taken in the preparation and publication of this document, errors in con
5、tent, typographical or otherwise, may occur. If you have comments concerning its accuracy, please write to “ETSI Editing and Standards Approval Dept.“ at the address shown on the title page. ETSI GSM*OY.L3 96 m 3400855 OLObOb2 439 m Page 3 GSM 04.13 Version 5.0.0: May 1996 Contents Foreword . 5 1 Sc
6、ope 7 2 Normative references 7 3 Definitions and abbreviations 8 3.1 Abbreviations . 8 3.2 Definitions 8 4 Default conditions 8 5 Requirements 8 5.1 General requirements 8 5.1.1 Response to layer 3 message . 8 5.1.2 Layer 3 Radio Resource signalling 9 5.2.0 Paging . 9 5.2.1 5.2.2 Paging commands and
7、 immediate assignment rejection (Timer T3122) 9 5.2.3 5.2.4 Channel assignment 9 5.2.5 Channel mode modify . 9 5.2.6 Handover access . 9 5.2.6.1 Finely, pseudo and pre synchronized cases 9 5.2.6.2 Non synchronized case . 10 5.2.7 Encryption 11 5.2.8 Classmark change 11 5.2.9 Classmark interrogation
8、11 5.2.1 O Release (Timer T31 10) . 11 5.2.1 1 Early sending of the CLASSMARK CHANGE message . 11 Layer 3 Mobility Management signalling 11 5.3.1 5.3.2 Identification 11 5.3.3 Authentication 11 5.3.4 T3240 expi sr 11 5.3.5 TMSI reallocation 12 5.3.6 IMSI detach . 12 5.3.7 5.3.8 Follow on call . 12 L
9、ayer 3 Call Control signalling . 12 5.4.1 Time to send SETUP message . 12 5.4.2 Response times to CC messages . 13 5.4.3 User alerting 13 5.4.4 Call establishment . 13 5.4.5 Call reestablishment 14 5.4.6 In call modification . 14 5.4.7 DTMF 14 Supplementary service signalling 14 5.5.1 Advice of Char
10、ge Charging (AoCC) 14 Short Message Services Point to Point . 14 Response to an erroneous layer 3 message . 8 Paging and Cell reselection after Channel Release 9 Immediate assignment (Timer T3101) 9 5.2 5.3 Periodic location updating timer 11 Location updating with random access failure 12 5.4 5.5 5
11、.6 5.6.1 CP-DATA . 14 5.6.2 RP-DATA . 14 History 15 ETSI GSfl*04-L3 96 3400855 0106063 375 Page 4 GSM 04.13 Version 5.0.0: May 1996 Blank page ETSI GSM*04=l13 96 3400655 OLObOb4 201 Page 5 GSM 04.13 Version 5.0.0: May 1996 Foreword This Global System for Mobile communications Technical Specification
12、 (GTS) has been produced by the Special Mobile Group (SMG) Technical Committee (TC) of the European Telecommunications Standards Institute (ETSI). This GTS provides a mechanism giving reliable transfer of signalling messages within the digital cellular telecornmunications system (Phase 2/Phase 2+).
13、This GTS is a TC-SMG approved GSM technical specification version 5, which contains GSM Phase 2+ enhancementdfeatures to the version 4 GSM technical specification. The ETS from which this Phase 2+ GTS has evolved is Phase 2 GSM 04.13 version 4.2.0. GTS are produced by TC-SMG to enable the GSM Phase
14、2 + specifications to become publicly available, prior to submission for the formal ETSI standards approval procedure to become European Telecommunications Standards (ETS). This ensures the earliest possible access to GSM Phase 2 + specifications for all Manufacturers, Network operators and implemen
15、tors of the Global System for Mobile communications. The contents of this GTS are subject to continuing work within TC-SMG and may change following formal TC-SMG approval. Should TC-SMG modify the contents of this GTS it will then be republished by ETSI with an identifying change of release date and
16、 an increase in version number as follows: Version 5.x.y where: y the third digit is incremented when editorial only changes have been incorporated in the specif ication; x the second digit is incremented for all other types of changes, .e. technical enhancements, corrections, updates, etc. NOTE: TC
17、-SMG has produced documents which give the technical specifications for the implementation of the digital cellular telecommunications system. Historically, these documents have been identified as GSM Technical Specifications (GSM-TSs). These TSs may have subsequently become I-ETSs (Phase l), or ETSs
18、/ETSI Technical Reports (ETRs) (Phase 2). TC-SMG has also produced ETSI GSM TSs which give the technical specifications for the implementation of Phase 2+ enhancements of the digital cellular telecommunications system. These version 5.x.x GSM Technical Specifications may be referred to as GTSs. Page
19、 6 GSM 04.1 3 Version 5.0.0: May 1996 Blank page ETSI GSM*O4-13 96 3400855 OLObObb 084 Page 7 GSM 04.13 Version 5.0.0: May 1996 1 Scope This Global System for Mobile communications Technical Specification (GTS) specifies measurable performance requirements for signalling aspects of mobile stations.
20、To allow implementation flexibility it has been chosen to specify requirements on the whole mobile station rather than to specify requirements on each “OS1 layer“. As a consequence the performance requirements do not fit conveniently in specifications such as TS GSM 04.08 (layer 3 only) or TS GSM 04
21、.06 (layer 2 only). The main aim of this GTS is to provide the justification for testing of requirements that are not included in other GSM specifications. Where specific requirements are included in other GSM specifications they are not duplicated here. Mobile Stations have to perform a wide variet
22、y of functions. As a consequence most performance measurements have to be made under a set of defined conditions: where necessary, these are included in this GTS. Where necessary certain assumptions are made about the interaction times between the mobile equipment and the SIM. If the (test) SIM does
23、 not respond within the assumed time then appropriate allowances shall be made. Additionally, it is intended that this GTS should contain sufficient requirements to enable some undefined network timers in TS GSM 04.08 to be calculated. 2 Normative references This GTS incorporates by dated and undate
24、d reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this GTS only when incorporated in
25、it by amendment or revision. For undated references, the latest edition of the publication referred to applies. PI 31 141 151 161 171 GSM O1 .O4 (ETR 100): “Digital cellular telecommunications system (Phase 2); Abbreviations and acronyms“. GSM 03.22 (ETS 300 535): “Digital cellular telecommunication
26、s system (Phase 2); Functions related to Mobile Station (MS) in idle mode“. GSM 04.06 (ETS 300 555): “Digital cellular telecommunications system (Phase 2); Mobile Station - Base Station System (MS - BSS) interface Data Link (DL) layer specification“. GSM 04.08 (ETS 300 557): “Digital cellular teleco
27、mmunications system (Phase 2); Mobile radio interface layer 3 specification“. GSM 04.86 (ETS 300 570): “Digital cellular telecommunications system (Phase 2); Advice of Charge (AOC) supplementary services - Stage 3“. GSM 05.02 (ETS 300 574): “Digital cellular telecommunications system (Phase 2); Mult
28、iplexing and multiple access on the radio path“. GSM 05.08 (ETS 300 578): “Digital cellular telecommunications system (Phase 2); Radio subsystem link control“. ETSI GSM*O4*L3 96 3400855 OLObOb7 TLO Page 8 GSM 04.13 Version 5.0.0: May 1996 3 Definitions and abbreviations 3.1 Abbreviations Abbreviatio
29、ns used in this GTS are listed in GSM 01.04. 3.2 Definitions Ready to transmit In this GTS the phrase “ready to transmit the message before time x is defined to mean that the MS shall transmit part of that message no later than the first burst of the first TCH or control channel block that occurs af
30、ter time x. 4 Def a u I t conditions Unless otherwise stated, throughout this GTS the following conditions are associated with the requirements: 5 ideal radio link with an insignificant bit error rate; no other signalling is in progress on the main DCCH; messages sent by the network are correctly fo
31、rmed; the only established data link (or the only data link to be established) is on SAPI O; any Starting Time IE that is included in a message sent by the network does not require the action to be delayed; cells are not barred and all access classes are allowed; the layer 2 performance of the netwo
32、rk shall satisfy the “System Performance Requirements“ of subclause 5.9 of TS GSM 04.06; messages sent by the network may contain any set of optional IEs, and any permitted set of conditional IEs; the mobile has a valid SIM inserted, is powered on, and the SIMS update status is “updated“; and on the
33、 CCCH, the Page Mode IE is not set to “paging reorganisation“ or “same as before“. Requirements 5.1 General requirements 5.1.1 Response to layer 3 message The requirements of subclause 5.1.1 apply if there are no specific requirements for a layer 3 message in other parts of clause 5. If the last tim
34、eslot of the message block containing a network command occurs at time T, then the MS shall be ready to transmit the response before time T + 500 ms. 5.1.2 Response to an erroneous layer 3 message If the last timeslot of the message block containing an erroneous RR, MM or CC message occurs at time T
35、 and if TS GSM 04.08 requires a status message to be returned to the network then the MS shall be ready to transmit the RR-STATUS or MM-STATUS or STATUS message before T + 500 ms. ETSI GSN*O4-13 9b 3400855 OlObObB 957 Page 9 GSM 04.13 Version 5.0.0: May 1996 5.2 Layer 3 Radio Resource signalling 5.2
36、.0 Paging If access to the network is allowed and the MS has been camped on a suitable cell for at least 2 seconds and if the last timeslot of the message block containing a PAGING REQUEST message addressing the MS occurs at time T, then the MS shall be ready to transmit the CHANNEL REQUEST message
37、before T+ 0.7 s. 5.2.1 Paging and Cell reselection after Channel Release If the last timeslot of the message block containing a CHANNEL RELEASE message occurs at time T the MS shall respond to PAGING REQUEST messages sent later than T + 1 .O seconds. 5.2.2 Paging commands and immediate assignment re
38、jection (Timer T3122) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT REJECT message is sent at time T and contains a Wait Indication of W seconds then the MS shall at least respond to PAGING REQUEST messages sent later than T + (W + 1) seconds. 5.2.3 Immediate assignmen
39、t (Timer T3101) If the last timeslot of the message block containing an IMMEDIATE ASSIGNMENT (or IMMEDIATE ASSIGNMENT EXTENDED) message is transmitted at time T then, the MS shall be ready to transmit the SABM frame with its information field before T + 25 ms. This requirement shall apply for assign
40、ment to TCH/F, TCH/H and SDCCH. 5.2.4 Channel assignment If the last timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T, then the MS shall be ready to transmit the ASSIGNMENT COMPLETE message before T + 600 ms. If the last timeslot of the message block containing an ASSI
41、GNMENT COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the ASSIGNMENT FAILURE message on the old channel before T + 2 seconds. If the la
42、st timeslot of the message block containing an ASSIGNMENT COMMAND occurs at time T and this ASSIGNMENT COMMAND is such that the MS shall not attempt to establish a layer 2 link on the new channel, then the MS shall be ready to transmit any ASSIGNMENT FAILURE message on the old channel before T + 500
43、 mc. 5.2.5 Channel mode modify If the last timeslot of the message block containing a CHANNEL MODE MODIFY message occurs at time T, then the MS shall be ready to transmit the CHANNEL MODE MODIFY ACKNOWLEDGE message before T + 300 ms. In the case that the call is a voice group or voice broadcast call
44、 the MS shall be ready to transmit the CHANNEL MODE ACKNOWLEDGE message before T + 50 ms. 5.2.6 Handover access 5.2.6.1 Finely, pseudo and pre synchronized cases If the last timeslot of the message block containing a HANDOVER COMMAND message to a full rate TCH occurs at time T, then the MS shall be
45、ready to transmit the HANDOVER COMPLETE message before T + 650 ms. If the last timeslot of the message block containing a HANDOVER COMMAND message to a half rate TCH occurs at time T, then the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 900 rns. ETSI GSM*04-13 96 3400855 O
46、LObOb7 893 = Page 10 GSM 04.13 Version 5.0.0: May 1996 If the last timeslot of the message block containing a HANDOVER COMMAND message to an SDCCH occurs at time T, then the MS shall be ready to transmit the HANDOVER COMPLETE message before T + 1.5 seconds. If the last timeslot of the message block
47、containing a HANDOVER COMMAND to a full rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old full rate
48、 TCH before T+2s. If the last timeslot of the message block containing a HANDOVER COMMAND to a full rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready t
49、o transmit the HANDOVER FAILURE message on the old SDCCH before T + 2.5 seconds. If the last timeslot of the message block containing a HANDOVER COMMAND to a half rate TCH occurs at time T and this HANDOVER COMMAND is such that the MS tries but fails to establish a layer 2 link on the new channel and thus reverts to the old channel, then the MS shall be ready to transmit the HANDOVER FAILURE message on the old half rate TCH before T + 3 seconds. If the last timeslot of the message block containing a HANDOVER COMMAND to a half rate TCH occurs at time T and this HANDOVER COMMAND i
