1、 ETSI TS 100 392-5 V2.4.1 (2016-03) Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D) and Direct Mode Operation (DMO); Part 5: Peripheral Equipment Interface (PEI) TECHNICAL SPECIFICATION ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)2 Reference RTS/TETRA-03227 Keywords data, interface, TETRA, V+D,
2、voice ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded fr
3、om: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or per
4、ceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to rev
5、ision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/Comm
6、iteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written
7、authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM an
8、d LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)3 Contents Intellectual Property Rights 22g3Foreword . 22g3Modal v
9、erbs terminology 23g31 Scope 24g32 References 24g32.1 Normative references . 24g32.2 Informative references 26g33 Symbols and abbreviations . 26g33.1 Symbols 26g33.2 Abbreviations . 27g34 Overview of TETRA PEI . 30g34.1 Introduction 30g34.2 Protocol architecture. 31g34.3 Context model 31g34.4 Void 3
10、5g34.5 SDS Message stacks . 35g34.5.0 General on SDS Message stacks . 35g34.5.1 Status message texts 35g34.5.2 SDS 1 message texts . 35g34.5.3 Status and SDS types 1, 2 and 3 . 35g34.5.4 SDS type 4 36g34.6 Phone books . 36g34.7 Reserved status values considerations 36g34.8 SDS-TL considerations 36g3
11、4.9 AT commands 37g34.9.1 General on AT commands 37g34.9.2 AT command state 38g34.9.3 AT circuit mode data state 39g34.9.4 TNP1 and packet data state . 39g34.9.5 Transitions between states 40g34.9.5.1 Transition from AT command state to AT circuit mode data state . 40g34.9.5.2 Transition from AT cir
12、cuit mode data state to AT command state . 40g34.9.5.3 Transition from AT command state to TNP1 or packet data state 40g34.9.5.4 Transition from TNP1 and packet data state to AT command state 40g34.10 TNP1 and IP network layer 41g34.10.1 General operation 41g34.10.2 IP addressing . 41g34.10.3 Local
13、mode . 41g34.10.4 Wide mode 42g34.11 TNP1 operation 42g34.12 Link start up at the MT . 43g35 Physical layer . 43g35.1 General on physical layer . 43g35.2 Physical layer for V.24/V.28 43g35.2.1 Electrical characteristics for V.24/V.28 43g35.2.2 Physical connection 44g35.2.3 Character format . 44g35.2
14、.4 Data transmission rate for V.24/V.28 . 45g35.3 Wire-line high rate connectivity technologies 45g35.3.1 General 45g35.3.2 Universal Serial Bus . 46g35.3.3 USB On-The-Go . 46g35.4 Wireless high rate connectivity 47g35.4.1 General 47g3ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)4 5.4.2 Wireless Security
15、47g35.4.3 Certified Wireless USB 47g35.4.4 Bluetooth 47g36 AT command set 48g36.1 General on AT command set 48g36.2 Limitations . 48g36.3 SDS user data . 48g36.4 AT command syntax 49g36.4.1 General on AT command syntax 49g36.4.2 Command line . 49g36.4.2.0 Command line structure 49g36.4.2.1 Prefix .
16、49g36.4.2.2 Body 49g36.4.2.3 Termination Character 49g36.4.2.4 Concatenating extended commands 50g36.4.2.5 Multiline extended commands 50g36.4.3 Command types 50g36.4.4 Parameters. 51g36.4.5 AT command examples 51g36.4.6 Information responses and result codes 52g36.4.6.1 General on information respo
17、nses and result codes 52g36.4.6.2 Information Responses 52g36.4.6.3 Result Code. 53g36.4.6.4 AT result examples in verbose mode 53g36.4.6.5 AT result examples in numeric mode 55g36.4.6.6 Aborting information results and result codes. 56g36.4.7 Handling of unknown parameters . 56g36.5 Existing V.250
18、commands for call control . 57g36.5.1 Commands 57g36.5.2 Result Codes . 57g36.5.3 Dialled string and user identity . 57g36.6 Existing V.250 commands for PEI control . 58g36.6a Modified V.250 commands for PEI control . 58g36.6a.1 General on modified V.250 commands for PEI control 58g36.6a.2 Line term
19、ination character: S3 58g36.6a.2.1 General on S3 58g36.6a.2.2 Description 59g36.6a.2.3 S3 set syntax 59g36.6a.2.4 S3 read syntax . 59g36.6a.2.5 S3 read result code text . 59g36.6a.2.6 S3 test syntax 59g36.6a.2.7 S3 test result syntax . 59g36.6a.3 Response formatting character: S4 . 59g36.6a.3.1 Gene
20、ral on S4 59g36.6a.3.2 Description 59g36.6a.3.3 S4 set syntax 59g36.6a.3.4 S4 read syntax . 60g36.6a.3.5 S4 read result code text . 60g36.6a.3.6 S4 test syntax 60g36.6a.3.7 S4 test result syntax . 60g36.6a.4 Line editing character: S5 . 60g36.6a.4.1 General on S5 60g36.6a.4.2 Description 60g36.6a.4.
21、3 S5 set syntax 60g36.6a.4.4 S5 read syntax . 60g36.6a.4.5 S5 read result code text . 60g36.6a.4.6 S5 test syntax 61g36.6a.4.7 S5 test result syntax . 61g36.6a.5 Echo: E . 61g36.6a.5.1 General on E 61g36.6a.5.2 Description 61g3ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)5 6.6a.5.3 E set syntax . 61g36.6a
22、.5.4 E read syntax . 61g36.6a.5.5 E read result code text . 61g36.6a.5.6 E test syntax 61g36.6a.5.7 E test result syntax 61g36.6a.6 Result code suppression: Q . 62g36.6a.6.1 General on Q . 62g36.6a.6.2 Description 62g36.6a.6.3 Q set syntax . 62g36.6a.6.4 Q read syntax 62g36.6a.6.5 Q read result code
23、 text . 62g36.6a.6.6 Q test syntax 62g36.6a.6.7 Q test result syntax 62g36.6a.7 MT response format: V . 62g36.6a.7.1 General on V . 62g36.6a.7.2 Description 62g36.6a.7.3 V set syntax . 62g36.6a.7.4 V read syntax 63g36.6a.7.5 V read result code text . 63g36.6a.7.6 V test syntax 63g36.6a.7.7 V test re
24、sult syntax 63g36.6a.8 Circuit 109 (DCD) behavior: Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no i
25、nvestigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Sp
26、ecification (TS) has been produced by ETSI Technical Committee TETRA and Critical Communications Evolution (TCCE). The present document is part 5 of a multi-part deliverable covering the Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D) and Direct Mode Operation (DMO), as identified below: ET
27、SI EN 300 392-1: “General network design“; ETSI EN 300 392-2: “Air Interface (AI)“; ETSI EN 300 392-3: “Interworking at the Inter-System Interface (ISI)“; ETSI ETS 300 392-4: “Gateways basic operation“; ETSI TS 100 392-5: “Peripheral Equipment Interface (PEI)“; ETSI EN 300 392-7: “Security“; ETSI EN
28、 300 392-9: “General requirements for supplementary services“; ETSI EN 300 392-10: “Supplementary services stage 1“; ETSI EN 300 392-11: “Supplementary services stage 2“; ETSI EN 300 392-12: “Supplementary services stage 3“; ETSI ETS 300 392-13: “SDL model of the Air Interface (AI)“; ETSI ETS 300 39
29、2-14: “Protocol Implementation Conformance Statement (PICS) proforma specification“; ETSI TS 100 392-15: “TETRA frequency bands, duplex spacings and channel numbering“; ETSI TS 100 392-16: “Network Performance Metrics“; ETSI TR 100 392-17: “TETRA V+D and DMO specifications“; ETSI TS 100 392-18: “Air
30、 interface optimized applications“. NOTE 1: Part 3, sub-parts 6 and 7 (Speech format implementation), part 4, sub-part 3 (Data networks gateway), part 10, sub-part 15 (Transfer of control), part 13 (SDL) and part 14 (PICS) of this multi-part deliverable are in status “historical“ and are not maintai
31、ned. NOTE 2: Some parts are also published as Technical Specifications such as ETSI TS 100 392-2 and those may be the latest version of the document. ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)23 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need n
32、ot“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 100 392-5 V2.4.1 (2016
33、-03)24 1 Scope The present document specifies the functional and technical aspects of TETRA Peripheral Equipment Interface (PEI) that is the interface between a Terminal Equipment type 2 (TE2) and a Mobile Termination type 2 (MT2) at reference point RT. 2 References 2.1 Normative references Referenc
34、es are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. Referenced docum
35、ents which are not found to be publicly available in the expected location might be found at https:/docbox.etsi.org/Reference/. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents
36、 are necessary for the application of the present document. 1 ETSI EN 300 392-1: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 1: General network design“. 2 ETSI TS 101 369 (V7.2.0): “Digital cellular telecommunications system (Phase 2+); Terminal Equipment to Mobile Station (TE-MS
37、) multiplexer protocol (3GPP TS 07.10 version 7.2.0 Release 1998)“. 3 ETSI EN 300 392-2: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 2: Air Interface (AI)“. 4 Recommendation ITU-T V.24: “List of definitions for interchange circuits between data terminal equipment (DTE) and data c
38、ircuit-terminating equipment (DCE)“. 5 Recommendation ITU-T V.250: “Serial asynchronous automatic dialling and control“. 6 Recommendation ITU-T V.28: “Electrical characteristics for unbalanced double-current interchange circuits“. 7 Void. 8 Recommendation ITU-T T.50: “International Reference Alphabe
39、t (IRA) (Formerly International Alphabet No. 5 or IA5) - Information technology - 7-bit coded character set for information interchange“. 9 ETSI TS 127 007 (V12.8.0 (2015-04): “Digital cellular telecommunications system (Phase 2+); Universal Mobile Telecommunications System (UMTS); LTE; AT command s
40、et for User Equipment (UE) (3GPP TS 27.007 version 12.8.0 Release 12)“. 10 IETF RFC 1661: “The Point-to-Point Protocol (PPP)“. 11 IETF RFC 1662: “PPP in HDLC-like Framing“. 12 ETSI EN 300 392-9: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 9: General requirements for supplementary
41、 services“. 13 Recommendation ITU-T E.164: “The international public telecommunication numbering plan“. 14 ETSI EN 300 812-3: “Terrestrial Trunked Radio (TETRA); Subscriber Identity Module to Mobile Equipment (SIM-ME) interface; Part 3: Integrated Circuit (IC); Physical, logical and TSIM application
42、 characteristics“. ETSI ETSI TS 100 392-5 V2.4.1 (2016-03)25 15 ETSI ES 200 812-2: “Terrestrial Trunked Radio (TETRA); Subscriber Identity Module to Mobile Equipment (TSIM-ME) interface; Part 2: Universal Integrated Circuit Card (UICC); Characteristics of the TSIM application“. 16 ETSI ETS 300 392-1
43、2-7: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 12: Supplementary services stage 3; Sub-part 7: Short Number Addressing (SNA)“. 17 ETSI EN 300 392-12-16: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 12: Supplementary services stage 3; Sub-part 16: Pre-emptive
44、Priority Call (PPC)“. 18 ISO 8859-1: “Information technology - 8-bit single-byte coded graphic character sets - Part 1: Latin alphabet No. 1“. 19 Recommendation ITU-T T.35: “Procedure for the allocation of ITU-T defined codes for non-standard facilities“. 20 ETSI EN 300 392-7: “Terrestrial Trunked R
45、adio (TETRA); Voice plus Data (V+D); Part 7: Security“. 21 ETSI EN 300 392-12-8: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 12: Supplementary services stage 3; Sub-part 8: Area Selection (AS)“. 22 ETSI TS 100 392-2: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part
46、 2: Air Interface (AI)“. 23 ETSI TS 100 392-7: “Terrestrial Trunked Radio (TETRA); Voice plus Data (V+D); Part 7: Security“. 24 ETSI TS 100 392-15: “Terrestrial Trunked Radio (TETRA) Voice plus Data (V+D); Part 15: TETRA frequency bands, duplex spacings and channel numbering“. 25 ETSI EN 300 396-3:
47、“Terrestrial Trunked Radio (TETRA); Technical requirements for Direct Mode Operation (DMO); Part 3: Mobile Station to Mobile Station (MS-MS) Air Interface (AI) protocol“. 26 ETSI EN 300 396-6: “Terrestrial Trunked Radio (TETRA); Direct Mode Operation (DMO); Part 6: Security“. 27 Recommendation ITU-T
48、 V.42bis: “Data compression procedures for data circuit-terminating equipment (DCE) using error correction procedures“. 28 USB Implementers Forum, Inc.: “Universal Serial Bus (USB) Specification, Revision 2.0“. NOTE: Available at: http:/www.usb.org. 29 USB Implementers Forum Inc.: “On-The-Go and Emb
49、edded Host Supplement to the USB Revision 2.0 Specification Revision 2.0 version 1.1“. NOTE: Available at: http:/www.usb.org/developers/onthego/USB_OTG_and_EH_2-0.pdf. 30 USB Implementers Forum Inc.: “Wireless Universal Serial Bus Specification, Revision 1.0“. NOTE: Available at: http:/www.usb.org. 31 WiMedia Alliance: “Multiband OFDM Physical Layer Specification, Revision 1“. NOTE: Available at: http:/www.wimedia.org/en/index.asp. 32 Bluetooth Special Interest Group (SIG): “BLUETOOTH SPECIFICATION Version 2
