1、 ETSI TS 102 201 V1.2.1 (2005-01)Technical Specification Digital Video Broadcasting (DVB);Interfaces for DVB Integrated Receiver Decoder (DVB-IRD)European Broadcasting Union Union Europenne de Radio-Tlvision EBUUER ETSI ETSI TS 102 201 V1.2.1 (2005-01) 2 Reference RTS/JTC-DVB-159 Keywords broadcasti
2、ng, digital, DVB, video ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of th
3、e present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic version or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In
4、 case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of thi
5、s and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as auth
6、orized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2005. European Broadcasting Union 2005. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefi
7、t of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 201 V1.2.1 (2005-01) 3 Contents Intellec
8、tual Property Rights5 Foreword.5 1 Scope 6 2 References 6 3 Definitions and abbreviations.9 3.1 Definitions9 3.2 Abbreviations .9 4 Interface requirements for DVB-IRDs .10 4.1 RF input in the satellite IF range 10 4.1.1 Polarization switch, LNBs band and first IF input selection10 4.1.2 Azimuth cont
9、rol of a polar mount dish antenna10 4.2 RF input/output in the VHF/UHF range.10 4.2.1 RF input 10 4.2.2 RF output 10 4.3 Modem interface 10 4.3.1 PSTN modem10 4.3.1.1 External modem 10 4.3.1.1.1 DTE/DCE interface .10 4.3.1.1.2 PSTN link interface .11 4.3.1.2 Integrated modem .11 4.3.2 CATV and SMATV
10、 modem.11 4.3.2.1 DTE/DCE interface.12 4.3.2.2 RF interface to CATV/SMATV network12 4.4 Video signals 12 4.4.1 Baseband signals.12 4.4.2 RF modulated signals13 4.5 Audio signals13 4.5.1 Analogue audio signals.13 4.5.2 Digital audio signals .13 4.5.2.1 Linear PCM coded audio signals 13 4.5.2.2 Compre
11、ssed and multi-channel audio signals .13 4.5.3 RF modulated signals13 4.6 Digital audio video interface 14 4.6.1 Overview of the HDMI concept .14 4.6.2 Supported AV Formats .15 4.6.3 Supported Audio Formats.15 4.6.4 Connector16 4.7 Data signals output .17 4.7.1 Low bitrate serial data port .17 4.7.2
12、 High bitrate parallel data port .17 4.7.2.1 Connector type 17 4.7.2.2 Electrical requirements17 4.7.2.3 IEEE 1284 modes18 4.7.2.4 IEEE 1284 Peripheral - modes (mandatory) .18 4.7.2.5 IEEE 1284 Host mode (optional)20 4.7.3 High speed serial interface21 4.8 Physical interfaces for control signals21 4
13、.9 Interface for detachable Conditional Access (CA) module 21 4.10 Connectors22 Annex A (informative): Configuration examples 23 Annex B (informative): National differences on channel assignments in CATV installations32 ETSI ETSI TS 102 201 V1.2.1 (2005-01) 4 Annex C (informative): Bibliography.33 H
14、istory 34 ETSI ETSI TS 102 201 V1.2.1 (2005-01) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can b
15、e found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant
16、 to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Fo
17、reword This Technical Specification (TS) has been produced by Joint Technical Committee (JTC) Broadcast of the European Broadcasting Union (EBU), Comit Europen de Normalisation ELECtrotechnique (CENELEC) and the European Telecommunications Standards Institute (ETSI). The present document is the outp
18、ut version from the DVB Project (DVB TM 1326 Rev. 5) on 24 December 1998 to the JTC for handing over to CENELEC for the revision EN50201. Once the revised EN50201 is published by CENELEC, ETSI will withdraw the present document. NOTE: The EBU/ETSI JTC Broadcast was established in 1990 to co-ordinate
19、 the drafting of standards in the specific field of broadcasting and related fields. Since 1995 the JTC Broadcast became a tripartite body by including in the Memorandum of Understanding also CENELEC, which is responsible for the standardization of radio and television receivers. The EBU is a profes
20、sional association of broadcasting organizations whose work includes the co-ordination of its members activities in the technical, legal, programme-making and programme-exchange domains. The EBU has active members in about 60 countries in the European broadcasting area; its headquarters is in Geneva
21、. European Broadcasting Union CH-1218 GRAND SACONNEX (Geneva) Switzerland Tel: +41 22 717 21 11 Fax: +41 22 717 24 81 Founded in September 1993, the DVB Project is a market-led consortium of public and private sector organizations in the television industry. Its aim is to establish the framework for
22、 the introduction of MPEG-2 based digital television services. Now comprising over 200 organizations from more than 25 countries around the world, DVB fosters market-led systems, which meet the real needs, and economic circumstances, of the consumer electronics and the broadcast industry. ETSI ETSI
23、TS 102 201 V1.2.1 (2005-01) 6 1 Scope The present document is an application standard, identifying recommended interfaces for connections of Digital Video Broadcast Integrated Receiver Decoder (DVB-IRD) equipment. If a recommended interface is supported, then the full specification of that interface
24、, which may include options, applies. Interfaces not mentioned in the present document are not excluded, and especially interfaces which are under development at the time of drafting the present document may be added at a later stage. For mechanical and electrical details of the interfaces, referenc
25、e is made to existing standards of IEC or CENELEC wherever possible, or standards which are known to be in an advanced state of development. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are ei
26、ther specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the e
27、xpected location might be found at http:/docbox.etsi.org/Reference. 1 Void. 2 ETSI ETS 300 249: “Satellite Earth Stations and Systems (SES); Television Receive-Only (TVRO) equipment used in the Broadcasting Satellite Service (BSS)“. 3 ETSI ETS 300 784: “Satellite Earth Stations and Systems (SES); Te
28、levision Receive-Only (TVRO) satellite earth stations operating in the 11/12 GHz frequency bands“. 4 ETSI EN 300 473: “Digital Video Broadcasting (DVB); Satellite Master Antenna Television (SMATV) distribution systems“. 5 IEC 60169-2: “Radio frequency connectors. Part 2: coaxial unmatched connector“
29、. 6 IEC 60169-24: “Radio Frequency connectors. Part 24: Radio frequency coaxial connectors with screw coupling, typically for use in 75 Ohm cable distribution systems (type F)“. 7 IEC 60807-9: “Rectangular connectors for frequencies below 3 MHz. Part 9: Detail specification for a range of peritelevi
30、sion connectors“. 8 IEC 61938: “Audio, video and audiovisual systems - Interconnections and matching values - Preferred matching values of analogue signals“. 9 IEC 60933-1: “Audio, video and audiovisual systems - Interconnections and matching values. Part 1: 21 contact connector for video systems, a
31、pplication No 1“. 10 IEC 60933-5: “Audio, video and audiovisual systems - Interconnections and matching values. Part 5: Y/C connector for video systems - Electrical matching values and description of the connector“. 11 IEC 60958: “Digital audio interface“. 12 IEC 61030: “Audio, video and audiovisual
32、 systems - Domestic digital bus (D2B)“. 13 IEC 61319-1: “Interfaces for satellite receiving equipment - Part 1: Europe“. 14 IEC 61883: “Consumer electronic audio/video equipment - Digital interface“. ETSI ETSI TS 102 201 V1.2.1 (2005-01) 7 15 IEC 61937: “Digital audio - Interface for non-PCM encoded
33、 audio bitstreams applying 60958“. 16 CENELEC EN 50049-1: “Domestic and similar electronic equipment interconnection requirements: Peritelevision connector“. 17 CENELEC EN 50157-1: “AVLink, Part 1: General“. 18 CENELEC EN 50221: “Common Interface Specification for Conditional Access and other Digita
34、l Video Broadcasting Decoder Applications“. 19 Void. 20 IEEE 1394: “Standard for a high performance serial bus“. 21 IEEE 1284 (1994): “Signalling method for a bi-directional parallel peripheral interface for personal computers“. 22 ANSI/EIA RS232: “Interface between data terminal equipment and data-
35、circuit terminating equipment employing serial binary data interchange“. 23 Void. 24 ETSI ETS 300 001: “Attachments to the Public Switched Telephone Network (PSTN); General technical requirements for equipment connected to an analogue subscriber interface in the PSTN“. 25 ETSI ETR 154: “Digital Vide
36、o Broadcasting (DVB); Implementation guidelines for the use of MPEG-2 Systems, Video and Audio in satellite, cable and terrestrial broadcasting applications“. 26 IEC 60574-3: “Audiovisual, video and television equipment and systems. Part 3: Connectors for the interconnection of equipment in audiovis
37、ual systems“. 27 IEC 61076-4-105: “Connectors with assessed quality, for use in d.c., low frequency analogue and in digital high-speed data applications - Part 4: Printed board connectors - Section 105 : Detail specification for 9 mm circular connector with 3 to 8 contacts for use in a wide range of
38、 applications including the telecommunication“. 28 IEC 60268-11: “Sound system equipment. Part 11: Application of connectors for the interconnection of sound system components“. 29 ITU-T Recommendation V.21: “300 bits per second duplex modem standardized for use in the general switched telephone net
39、work“. 30 ITU-T Recommendation V.23: “600/1200-baud modem standardized for use in the general switched telephone network“. 31 ITU-T Recommendation V.22: “1200 bits per second duplex modem standardized for use in the general switched telephone network and on point-to-point 2-wire leased telephone-typ
40、e circuits“. 32 ITU-T Recommendation V.22 bis: “2400 bits per second duplex modem using the frequency division technique standardized for use on the general switched telephone network and on point-to-point 2-wire leased telephone-type circuits“. 33 ITU-T Recommendation V.25: “Automatic answering equ
41、ipment and general procedures for automatic calling equipment on the general switched telephone network including procedures for disabling of echo control devices for both manually and automatically established calls“. 34 ITU-T Recommendation V.42: “Error-correcting procedures for DCEs using asynchr
42、onous-to-synchronous conversion“. 35 ITU-T Recommendation V.42 bis: “Data compression procedures for data circuit-terminating equipment (DCE) using error correction procedures“. 36 Council Directive 91/263/EEC of 29 April 1991 on the approximation of the laws of the Member States concerning telecomm
43、unications terminal equipment, including the mutual recognition of their conformity. ETSI ETSI TS 102 201 V1.2.1 (2005-01) 8 37 EIA/CEA-861: “A DTV Profile for Uncompressed High Speed Digital Interfaces“. 38 ITU-T Recommendation V.32: “A family of 2-wire, duplex modems operating at data signalling r
44、ates of up to 9600 bit/s for use on the general switched telephone network and on leased telephone-type circuits“. 39 ITU-T Recommendation V.32 bis: “A duplex modem operating at data signalling rates of up to 14 400 bit/s for use on the general switched telephone network and on leased point-to-point
45、 2-wire telephone-type circuits“. 40 ITU-T Recommendation V.34: “A modem operating at data signalling rates of up to 33 600 bit/s for use on the general switched telephone network and on leased point-to-point 2-wire telephone-type circuits“. 41 ETSI ETS 300 158: “Satellite Earth Stations and Systems
46、 (SES); Television Receive Only (TVRO-FSS) Satellite Earth Stations operating in the 11/12 GHz FSS bands“. 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: CATV (Community Antenna Television system): system designed
47、primarily to provide sound and television signals to communities SMATV (Satellite Master Antenna Television system): system designed to provide sound and television signals to the households of a building or group of buildings NOTE: Two system configurations are defined in EN 300 473 4 as follows: S
48、MATV system A, based on transparent transmodulation of QPSK satellite signals into QAM signals to be distributed to the user; SMATV system B, based on direct distribution of QPSK signals to the user, with two options: - SMATV-IF distribution on the satellite IF band (above 950 MHz); - SMATV-S distri
49、bution on the VHF/UHF band, for example the extended S-band (230 MHz to 470 MHz). 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: BSS Broadcast Satellite Service CA Conditional Access CENELEC Comit Europen de Normalisation ELECtrotechnique CTS Clear To Send CVBS Composite Video, Blanking and Sync DTE/DCE Data Terminal Equipment/Data Communication Equipment DVB Digital Video Broadcasting FSS Fixed Satellite Service GND signal GrouND
