1、 ETSI TS 103 361 V1.1.1 (2016-03) Short Range Devices (SRD) using Ultra Wide Band technology (UWB); Receiver technical requirements, parameters and measurement procedures to fulfil the requirements of the Directive 2014/53/EU TECHNICAL SPECIFICATION ETSI ETSI TS 103 361 V1.1.1 (2016-03)2 Reference D
2、TS/ERM-TGUWB-140 Keywords measurement, receiver, SRD, UWB ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Import
3、ant notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written a
4、uthorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document sho
5、uld be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the fo
6、llowing services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PD
7、F version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI
8、registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 103 361 V1.1.1 (2016-03)3 Contents Intel
9、lectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 5g3Introduction 5g31 Scope 6g32 References 6g32.1 Normative references . 6g32.2 Informative references 6g33 Definitions, symbols and abbreviations . 11g33.1 Definitions 11g33.2 Symbols 12g33.3 Abbreviations . 12g34 Purpose of receiver
10、parameters 13g35 Receiver performance criteria and level of performance . 14g36 Receiver parameters . 14g36.1 Introduction 14g36.2 Receiver parameters in ETSI EG 203 336 14g36.2.1 Receiver sensitivity . 14g36.2.2 Receiver co-channel rejection . 15g36.2.3 Receiver Selectivity and Blocking 15g36.2.4 R
11、eceiver dynamic range 15g36.2.5 Reciprocal mixing . 15g36.2.6 Desensitisation 16g36.3 Receiver parameter for ultra-wideband applications: Interferer signal handling 16g37 Potential interferers 17g37.1 Introduction 17g37.2 Complete list of interferers . 17g37.3 The concept of service groups and inter
12、ferer power levels 24g37.4 Interferers for indoor applications 24g37.5 Interferers for outdoor applications 27g37.6 Interferers for mobile (indoor and outdoor) applications . 30g37.7 Interferers for level probing and tank level probing applications . 33g37.8 Interferers for automotive applications .
13、 37g37.8.1 Devices inside the surface and not in the passenger area 37g37.8.2 Devices outside the surface or within the passenger area . 38g38 Test signal 39g39 Test procedure 40g39.1 Definitions 40g39.1.1 Receiver operating frequency range . 40g39.1.2 Interferer test frequency range 40g39.2 Test se
14、tup 40g39.2.1 Definition of the scenario, performance criterion and level of performance 40g39.2.2 Required text for the user manual . 41g39.2.3 DUT orientations and polarization directions . 41g39.2.4 Environmental conditions . 41g39.3 Test for interferer signal handling 41g39.4 Recommended tests 4
15、2g39.4.1 Building material sensor . 42g39.4.2 Respiration sensor . 43g39.4.3 Presence sensor . 43g39.4.4 Distance measurement system 43g3ETSI ETSI TS 103 361 V1.1.1 (2016-03)4 9.4.5 On-body pulse rate sensor . 44g39.4.6 Communications device 44g39.4.7 (T)LPR Method 45g39.4.8 GPR/WPR device . 47g3Ann
16、ex A (informative): Information on Performance Criteria . 48g3A.1 Communication devices . 48g3A.2 Sensor devices 51g3Annex B (informative): Text blocks for harmonised standards . 52g3B.1 Receiver Conformance Requirements (4.4) . 52g3B.2 Conformance methods of measurement for receiver (6.6) . 52g3Ann
17、ex C (informative): Test signal generation 53g3Annex D (informative): Derivation of the Equations for (T)LPR 57g3Annex E (informative): Change History 60g3History 61g3ETSI ETSI TS 103 361 V1.1.1 (2016-03)5 Intellectual Property Rights IPRs essential or potentially essential to the present document m
18、ay have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI
19、standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs n
20、ot referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). Mo
21、dal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are
22、 NOT allowed in ETSI deliverables except when used in direct citation. Introduction In June 2016, the Directive 2014/53/EU i.1 will replace the R Measurement Techniques“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version num
23、ber) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarante
24、e their long term validity. The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. i.1 Directive 2014/53/EU of the European Parliament and of the Council of 16 April 2014 on the harmonisation
25、 of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.2 Directive 1999/5/EC of the European Parliament and of the Council of 9 March 1999 on radio equipment and telecommunications terminal equipment and the mutual rec
26、ognition of their conformity. i.3 ETSI EG 203 336: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of technical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.4 IEEE 802.15.4-2011: “Pa
27、rt 15.4: Low-rate wireless personal area networks (LR-WPANs)“, September 2011. i.5 ETSI EN 302 510-1 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Radio equipment in the frequency range 30 MHz to 37,5 MHz for Ultra Low Power Active Medical Membrane Implants and Accessori
28、es; Part 1: Technical characteristics and test methods“. i.6 ETSI TR 102 309 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Ultra Low Power Active Medical Implants (ULP-AMI); “Membrane Implant“ devices operating in the 30 MHz to 37,5 MHz band; System Reference Document“.
29、ETSI ETSI TS 103 361 V1.1.1 (2016-03)7 i.7 ETSI EN 300 220-1 (V2.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Short Range Devices (SRD); Radio equipment to be used in the 25 MHz to 1 000 MHz frequency range with power levels ranging up to 500 mW; Part 1: Technical character
30、istics and test methods“. i.8 ETSI EN 300 224-1 (V1.3.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); On-site paging service; Part 1: Technical and functional characteristics, including test methods“. i.9 ETSI EN 302 077-1 (V1.1.1): “Electromagnetic compatibility and Radio spect
31、rum Matters (ERM); Transmitting equipment for the Terrestrial - Digital Audio Broadcasting (T-DAB) service; Part 1: Technical characteristics and test methods“. i.10 ETSI EN 302 054-1 (V1.2.1): “Meteorological Aids (Met Aids); Radiosondes to be used in the 400,15 MHz to 406 MHz frequency range with
32、power levels ranging up to 200 mW; Part 1: Technical characteristics and test methods“. i.11 ETSI EN 302 152-1 (V1.1.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Satellite Personal Locator Beacons (PLBs) operating in the 406,0 MHz to 406,1 MHz frequency band; Part 1: Technica
33、l characteristics and methods of measurement“. i.12 ETSI EN 301 502 (V12.1.6): “Global System for Mobile communications (GSM); Base Station (BS) equipment; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. i.13 ETSI TS 145 005 (V12.5.0): “Digital ce
34、llular telecommunications system (Phase 2+); Radio transmission and reception (3GPP TS 45.005 version 12.5.0 Release 12)“. i.14 ETSI EN 301 511 (V12.1.1): “Global System for Mobile communications (GSM); Harmonized EN for mobile stations in the GSM 900 and GSM 1800 bands covering essential requiremen
35、ts under article 3.2 of the R Radio Frequency Identification Equipment operating in the band 865 MHz to 868 MHz with power levels up to 2 W and in the band 915 MHz to 921 MHz with power levels up to 4 W; Part 1: Technical requirements and methods of measurement“. i.16 ETSI EN 302 018-1 (V1.2.1): “El
36、ectromagnetic compatibility and Radio spectrum Matters (ERM); Transmitting equipment for the Frequency Modulated (FM) sound broadcasting service; Part 1: Technical characteristics and test methods“. i.17 ETSI EN 300 422-2 (V1.4.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Wir
37、eless microphones in the 25 MHz to 3 GHz frequency range; Part 2: Harmonized EN covering the essential requirements of article 3.2 of the R Harmonised EN covering the essential requirements of article 3.2 of the R Part 13: Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE)“. i.1
38、9 ETSI EN 301 908-3 (V7.1.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 3: CDMA Direct Spread (UTRA FDD) Base Stations (BS)“. i.20 ETSI EN 301 908-2 (V11.0.1 draft): “IMT cellular networks; Harmonised Standard covering the essential requir
39、ements of article 3.2 of the Radio Equipment Directive 2014/53/EU; Part 2: CDMA Direct Spread (UTRA FDD) User Equipment (UE)“. i.21 ETSI EN 301 908-4 (V6.2.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 4: CDMA Multi-Carrier (cdma2000) User
40、 Equipment (UE)“. i.22 ETSI EN 301 908-5 (V5.2.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 5: CDMA Multi-Carrier (cdma2000) Base Stations (BS)“. ETSI ETSI TS 103 361 V1.1.1 (2016-03)8 i.23 ETSI EN 300 422-1 (V1.5.1): “Electromagnetic com
41、patibility and Radio spectrum Matters (ERM); Wireless microphones in the 25 MHz to 3 GHz frequency range; Part 1: Technical characteristics and methods of measurement“. i.24 ETSI EN 301 166-1 (V1.3.2): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Land Mobile Service; Radio equipm
42、ent for analogue and/or digital communication (speech and/or data) and operating on narrow band channels and having an antenna connector; Part 1: Technical characteristics and methods of measurement“. i.25 ETSI TS 100 910 (V8.20.0): “Digital cellular telecommunications system (Phase 2+); Radio Trans
43、mission and Reception (3GPP TS 05.05 version 8.20.0 Release 1999)“. i.26 ETSI TS 136 104 (V12.9.0): “LTE; Evolved Universal Terrestrial Radio Access (E-UTRA); Base Station (BS) radio transmission and reception (3GPP TS 36.104 version 12.9.0 Release 12)“. i.27 ETSI TS 136 101 (V12.7.0): “LTE; Evolved
44、 Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) radio transmission and reception (3GPP TS 36.101 version 12.7.0 Release 12)“. i.28 ETSI TS 125 101 (V12.6.0): “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmission and reception (FDD) (3GPP TS 25.1
45、01 version 12.7.0 Release 12)“. i.29 ETSI EN 301 908-10 (V4.2.1): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Base Stations (BS), Repeaters and User Equipment (UE) for IMT-2000 Third-Generation cellular networks; Part 10: Harmonised Standard for IMT-2000, FDMA/TDMA (DECT) coveri
46、ng the essential requirements of article 3.2 of the Directive 2014/53/EU“. i.30 ETSI EN 300 175-2 (V2.6.1): “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical Layer (PHL)“. i.31 3GPP2 C.S0002-E (V3.0): “Physical Layer Standard for cdma2000 Spread 2 Spectrum
47、 Systems“. i.32 ETSI EN 301 908-6 (V5.2.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 6: CDMA TDD (UTRA TDD) User Equipment (UE)“. i.33 ETSI TS 125 102: “Universal Mobile Telecommunications System (UMTS); User Equipment (UE) radio transmis
48、sion and reception (TDD) (3GPP TS 25.102)“. i.34 ETSI EN 301 908-7 (V5.2.1): “IMT cellular networks; Harmonized EN covering the essential requirements of article 3.2 of the R Part 7: CDMA TDD (UTRA TDD) Base Stations (BS)“. i.35 ETSI TS 125 104: “Universal Mobile Telecommunications System (UMTS); Ba
49、se Station (BS) radio transmission and reception (FDD) (3GPP TS 25.104)“. i.36 ETSI EN 301 908-14: “IMT cellular networks; Harmonised EN covering the essential requirements of article 3.2 of the R Part 14: Evolved Universal Terrestrial Radio Access (E-UTRA) Base Stations (BS)“. i.37 ETSI EN 302 064 (2.1.0): “Wireless Video Links operating in the 1,3 GHz to 50 GHz frequency band; Harmonised Standard covering the essential requirements of article 3.2 of the Directive 2014/53/EU“. i.38 3GPP2 C.S0010-D (V1.
