1、 ETSI TS 1Universal Mobile TelApplication of Q.1Circuit Switched (3GPP TS 29.2TECHNICAL SPECIFICATION129 205 V13.0.0 (2016elecommunications System (.1900 series to bearer independ (CS) core network architectStage 3 .205 version 13.0.0 Release 1316-01) (UMTS); endent cture; 13) ETSI ETSI TS 129 205 V
2、13.0.0 (2016-01)13GPP TS 29.205 version 13.0.0 Release 13Reference RTS/TSGC-0429205vd00 Keywords UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la So
3、us-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall
4、 not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Se
5、cretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please
6、send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permiss
7、ion of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the
8、ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 129 20
9、5 V13.0.0 (2016-01)23GPP TS 29.205 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members,
10、 and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to
11、the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. F
12、oreword This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. These should be interpreted as being references to the
13、corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and
14、“cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TS 129 205 V13.0.0 (2016-01)33GPP TS 29.205 version 13.0.0 R
15、elease 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 5g31 Scope 6g32 References 6g33 Definitions, symbols and abbreviations . 7g33.1 Definitions 7g33.2 Symbols 7g33.3 Abbreviations . 7g34 Protocols . 8g34.1 Call control protocol (Nc interface) 8g34.2
16、Interworking with other protocols 8g34.3 Resource control protocol (G)MSC and MGW (Mc Interface) 8g34.4 Bearer control protocol between MGWs (Nb interface) 9g34.5 Signalling Transport . 9g34.5.1 Call Control protocols . 9g34.5.2 Resource control protocol (G)MSC and MGW (Mc Interface) 9g34.5.3 Bearer
17、 control protocol between MGWs (Nb interface) . 9g3Annex A: Void . 10g3Annex B (normative): Transparent Support of Mobile Services . 11g3B.1 Introduction 11g3B.2 Mobile Service Transport (MST) Format and Codes 11g3B.2.1 Encapsulated Application Information . 11g3B.2.1.1 General Layout . 11g3B.2.1.2
18、List of Identifiers 13g3B.2.1.3 Mobile Equipment Identifier. 13g3B.2.1.4 LCLS Negotiation Request . 14g3B.2.1.5 LCLS Negotiation Response. 14g3B.2.1.6 LCLS Status 15g3B.2.1.7 LCLS Status Change . 15g3B.2.1.8 LCLS Status Result . 16g3B.2.1.9 LCLS Global Call Reference 16g3B.2.1.10 LCLS Configuration
19、Preference . 18g3B.2.1.11 LCLS Configuration Change Request 18g3B.2.1.12 LCLS Configuration Change Result . 19g3B.2.2 Application Transport Instruction Indicators . 19g3Annex C (normative): LCLS Service Application 20g3C.1 Use of MST ASE 20g3C.2 Procedures 20g3C.2.1 Indication of LCLS Capability . 2
20、0g3C.2.1.1 LCLS Service Capability Indication . 20g3C.2.1.2 Actions at Originating Serving Node 20g3C.2.1.3 Actions at Intermediate Serving Node 21g3C.2.1.4 Actions at Destination Serving Node 21g3C.2.2 Backward LCLS Negotiation during Call Setup 21g3C.2.2.1 Introduction. 21g3C.2.2.2 Actions at Dest
21、ination Serving Node 22g3ETSI ETSI TS 129 205 V13.0.0 (2016-01)43GPP TS 29.205 version 13.0.0 Release 13C.2.2.3 Actions at Intermediate Serving Node 22g3C.2.2.4 Actions at Originating Serving Node 22g3C.2.3 Answer message . 22g3C.2.3.1 Introduction. 22g3C.2.3.2 Actions at Destination Serving Node 22
22、g3C.2.3.3 Actions at Intermediate Serving Node 22g3C.2.3.4 Actions at Originating Serving Node 22g3C.2.4 LCLS Configuration Change Request 23g3C.2.4.1 Introduction. 23g3C.2.4.2 Actions at Initiating Serving Node . 23g3C.2.4.3 Actions at Intermediate Serving Node 23g3C.2.4.4 Actions at Terminating Se
23、rving Node 24g3C.2.5 LCLS Status Update . 24g3C.2.5.1 Introduction. 24g3C.2.5.2 Actions at Initiating Serving Node . 24g3C.2.5.3 Actions at Intermediate Serving Node 24g3C.2.5.4 Actions at Terminating Serving Node 24g3C.2.6 LCLS Status Change Request 24g3C.2.6.1 Introduction. 24g3C.2.6.2 Actions at
24、Initiating Serving Node . 25g3C.2.6.3 Actions at Intermediate Serving Node 25g3C.2.6.4 Actions at Terminating Serving Node 25g3Annex D (informative): Change history . 27g3History 28g3ETSI ETSI TS 129 205 V13.0.0 (2016-01)53GPP TS 29.205 version 13.0.0 Release 13Foreword This Technical Specification
25、has been produced by the 3rdGeneration Partnership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an id
26、entifying change of release date and an increase in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all cha
27、nges of substance, i.e. technical enhancements, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. ETSI ETSI TS 129 205 V13.0.0 (2016-01)63GPP TS 29.205 version 13.0.0 Release 131 Scope The present document describes the pr
28、otocols to be used when ITU-T Q.1902 “Bearer Independent Call Control“ is used as call control protocol in a 3GPP Bearer Independent CS core network 3GPP TS 23.205 1 The Q.1902 operates between (G)MSC servers .The BICC architecture as described in ITU-T Q.1902 6-10 consists of a number of protocols.
29、 The following types of protocols are described: call control protocol, bearer control protocols and a resource control protocol for this architecture. The architecture complies with the requirements imposed by 3GPP TS 23.205 1 and TS 23.153 2. The present document is valid for a 3rdgeneration PLMN
30、(UMTS) complying with Release 4 and later. Note: Q.1902 can be used in other network architectures than the one defined in 3GPP TS 23.205 1 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are eit
31、her specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do not apply. For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a n
32、on-specific reference implicitly refers to the latest version of that document in the same Release as the present document. 1 3GPP TS 23.205: “Bearer Independent CS Core Network Stage 2“. 2 3GPP TS 23153: “Out of Band Transcoder Control - Stage 2“. 3 3GPP TS 29.232: “Media Gateway Controller (MGC) M
33、edia Gateway (MGW) Interface; Stage 3“. 4 3GPP TS 29.414: “Core Network Nb Data Transport and Signalling Transport“. 5 ITU-T Recommendation Q.765.5 (06/2000): “Application Transport Mechanism“. 6 ITU-T Recommendation Q.1902.1 (07/2001): “Bearer Independent Call Control CS2 Functional Description“. I
34、nclusive Amendment 3: “Support for the Customized Alerting Tone (CAT) service“. 7 ITU-T Recommendation Q.1902.2 (07/2001): “Bearer Independent Call Control CS2 General functions of messages and parameters“. Inclusive Amendment 5: “Support for the Customized Alerting Tone (CAT) service“. 8 ITU-T Q.19
35、02.3 (07/2001): “Bearer Independent Call Control CS2 Formats and Codes“. Inclusive Amendment 5: “Support for the Customized Alerting Tone (CAT) service“. 9 ITU-T Recommendation Q.1902.4 (07/2001): “Bearer Independent Call Control CS2 Basic Call Procedures“. 10 ITU-T Recommendation Q.1902.5 (07/2001)
36、: “Exceptions to the Application Transport Mechanism in the Context of Bearer Independent Call Control“. 11 ITU-T Recommendation Q.1902. 6 (07/2001): “Generic Signalling Procedures for the support of the ISDN User Part Supplementary Services and for bearer redirection“. 12 ITU-T Recommendation Q.195
37、0 (07/2001): “Call Bearer Control Protocol“. 13 ITU-T Recommendations Q.2630.1 (12/1999), Q.2630.2 (12/2000): “AAL type 2 signalling protocol“. ETSI ETSI TS 129 205 V13.0.0 (2016-01)73GPP TS 29.205 version 13.0.0 Release 1314 ITU-T Recommendation Q.1990 (07/2001): “BICC Bearer Control tunnelling pro
38、tocol“. 15 ITU-T Recommendation Q.1970 (07/2001): “BICC IP Bearer Control protocol“. 16 ITU-T Recommendation Q.1912.1 (07/2001): “Interworking between Signalling System No. 7 ISDN user part and the Bearer Independent Call Control protocol“. 17 ITU-T Recommendation Q.1912.2 (07/2001): “Interworking b
39、etween selected Signalling System (PSTN Access DSS1, C5, R1, R2, TUP) and the Bearer Independent Call Control Protocol“. 18 ITU-T Recommendation Q.2150.0 (05/2001): “Generic Signalling Transport Service“. 19 ITU-T Recommendation Q.2150.1 (05/2001): “Signalling Transport Converter on MTP3 and MTP3b“.
40、 20 ITU-T Recommendation Q.2150.3 (12/2002): “Signalling Transport Converter on SCTP“. 21 ITU-T Recommendation H.248.4 (11/2000): “Gateway Control Protocol: Transport over SCTP“. 22 3GPP TS 29.202: “SS7 signalling transport in core network“. 23 ITU-T Recommendation H.248.5 (11/2000): “Gateway contro
41、l protocol: Transport over ATM“. 24 ITU-T Q.765 (06/2000): “Signalling system No. 7 Application transport mechanism“. 25 3GPP TS 23.003: “Numbering, addressing and identification“. 26 3GPP TS 23.216: “Single Radio Voice Call Continuity (SRVCC); Stage 2“. 27 3GPP TS 23.237: “IP Multimedia subsystem (
42、IMS) Service Continuity; Stage 2“. 28 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 29 3GPP TS 23.284: “Local Call Local Switch; Stage 2“. 3 Definitions, symbols and abbreviations 3.1 Definitions 3.2 Symbols For the purposes of the present document, the following symbols apply: Nc Interface
43、between the (G)MSC servers. Mc Interface between the server and the media gateway. Nb Interface between media gateways (MGW). 3.3 Abbreviations For the purposes of the present document, the abbreviations as defined in 3GPP TR 21.905 28 and the following apply. An abbreviation defined in the present
44、document takes precedence over the definition of the same abbreviation, if any, in3GPP TR 21.905 28. APM Application Transport Mechanism Application Transport Message APP Application Transport Parameter BAT Bearer Association Transport BICC Bearer Independent Call Control C5 CCITT signalling system
45、number 5 GCR Global Call Reference ETSI ETSI TS 129 205 V13.0.0 (2016-01)83GPP TS 29.205 version 13.0.0 Release 13LCLS Local Call Local Switch M3UA MTP3 User Adaptation Layer MGC Media Gateway Controller MST Mobile Service Transport R1 Regional Signalling System 1 R2 Regional Signalling System 2 SCT
46、P Stream Control Transmission Protocol SN Serving Node TUP Telephony User Part 4 Protocols Implementations providing any of the interfaces or protocols identified in the subclauses below shall implement the requirements of the specifications identified in those subclauses. 4.1 Call control protocol
47、(Nc interface) Q.1902.1 BICC PROTOCOL (CS2) FUNCTIONAL DESCRIPTION 6 Q.1902.2 BICC PROTOCOL (CS2) AND SIGNALLING SUSTEM NO 7 ISUP GENERAL FUNCTIONS OF MESSAGES AND PARAMETERS 7 Q.1902.3 BICC PROTOCOL (CS2) AND SIGNALLING SYSTEM NO 7 ISUP FORMATS AND CODES 8 (NOTE) Q.1902.4 BICC (CS2) BASIC CALL PROC
48、EDURES 9 Q.1902.5 EXCEPTIONS TO THE APM IN THE CONTEXT OF BICC 10 AMENDMENT TO ITU-T RECOMMENDATION Q.765.5 FOR BICC CS2 5 Q.1902.6 GENERIC SIGNALLING PROCEDURES AND SUPPORT OF THE ISDN USER PART SUPPLEMENTARY SERVICES WITH THE BEARER INDEPENDENT CALL CONTROL PROTOCOL 11 NOTE: The “Backward CAT indi
49、cators“ parameter shall be encoded as an optional 3-octet parameter in the ACM, CPG and SEG messages rather than as a 1-octet parameter as incorrectly defined in Amendment 5 of ITU-T Recommendation Q.1902.3 8. 4.2 Interworking with other protocols Q.1912.1 ISUP-BICC INTERWORKING 16 Q.1912.2 INTERWORKING BETWEEN SELECTED SIGNALLING SYSTEMS (PSTN ACCESS DSS1 C5 R1 R2 TUP) AND THE BEARER INDEPENDENT CALL CONTROL PROTOCOL 17 4.3 Resource control protocol (G)MSC and MGW (
