FORD C-1-2008 SCALE (Version 28).pdf

上传人:livefirmly316 文档编号:744756 上传时间:2019-01-14 格式:PDF 页数:3 大小:114.12KB
下载 相关 举报
FORD C-1-2008 SCALE (Version 28).pdf_第1页
第1页 / 共3页
FORD C-1-2008 SCALE (Version 28).pdf_第2页
第2页 / 共3页
FORD C-1-2008 SCALE (Version 28).pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 FECDS C-1 Engineering CAD & Drafting Standards Ford Proprietary and/or Confidential Information - Do not distribute to others w/o prior written authorization. Version 28 TOC Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20081231C11 Printed copies are uncontrolled.SCALE 1

2、INTRODUCTION 1.1 All CAD models shall be created at full size, (i.e., one drawing unit of the CAD system used will equal one unit of base measuring system). NOTE: In order to fit full size CAD models on the drawing formats, it may be necessary to create scaled-down viewing areas in the drafting mode

3、 of the CAD System. Examples of this technique are “View Ports” in AutoCAD or “View at a Scale” in IDEAS. The term scale is in reference to these viewing areas, and will be denoted in the “SCALE” region of the title block. 1.2 Drawings created manually must be accurately drawn to scale and, as a gen

4、eral rule, drawn full size. 2 DEFINITIONS (Reserved) 2.1 CAD Design/Vehicle Verification 2.1.1 The nominal and variational study, review, recording and confirmation of vehicle compatibility attributes using CAD tools and GDT, See Standard D1. 3 REQUIREMENTS 3.1 PREFERRED SCALE 3.1.1 The preferred sc

5、ale is full size. If another scale is necessary, use a scale specified as a ratio as shown in Figure C1.1. Where required, a scale based on the ratio of 1:X for downscaling and X:1 for upscaling may be used. 3.2 SCALE NOTATION 3.2.1 The general scale of a drawing is recorded in the appropriate space

6、 in the title block. Any views, sections, etc. drawn to a scale other than the general scale must have the scale shown directly under them. See Figure C1.2. 3.2.2 Drawings such as wiring diagrams, sketches, etc. not drawn to a scale shall have a single line drawn through the scale space in the title

7、 block. ENGINEERING CAD & DRAFTING STANDARDS Return to TOC SCALES 1 : 1 1 : 2 2 : 1 1 : 4 4 : 1 1 : 5 5 : 1 1 : 10 10 : 1 1 : 20 20 : 1 1 : 50 50 : 1 1 : 100 100 : 1 1 : 200 200 : 1 1 : 500 500 : 1 Figure C1.1 Figure C1.2 Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20081

8、231C12 Printed copies are uncontrolled.ENGINEERING CAD & DRAFTING STANDARDS Return to TOC 3.3 ENLARGED SCALE 3.3.1 Generally when a part is drawn to an enlarged scale, a supplementary view of the part at full size is not necessary. If, for clarity, it is deemed necessary it should be placed in the l

9、ower left-hand corner of the drawing as shown in Figure C1.3. Figure C1.3 3.4 DO NOT SCALE 3.4.1 The notation DO NOT SCALE may be added to the drawing if it is considered necessary. However, even if the note is not added it is essential that drawings are not scaled unless otherwise stated. 4 SPECIFICATIONS (Reserved) 5 ADDENDUM (Reserved) Original Issue: 19960419 Copyright, Ford Motor Company. Latest Re-issue: 20081231C13 Printed copies are uncontrolled.

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1