1、 ENGINEERING MATERIAL SPECIFICATIONMaterial Name Specification NumberDate Release No. Release/Revision1992 12 16 NB00E10043064000 Reactivated -A & Updated D. Keller1978 10 13 CAH1RD572066126 Metricated & Retyped1967 10 20 COW1-DC515332-1 ReleasedWP 3948-a Page 1 of 5 PRIMER SURFACER, LOW GLOSS, FIBE
2、RGLASS ESB-M6J106-AREINFORCED POLYESTER PLASTICSPRIMER SURFACER, HIGH GLOSS, FIBERGLASS ESB-M6J106-BREINFORCED POLYESTER PLASTICS1. SCOPEThe mate rials defined by these specifications are epoxy type primersurfacers with good adhesion an d enamel holdout properties when applied toreinforced polyester
3、 plastic surfaces.2. APPLICATIONThese specifications were released originally for material used as primersurfacers for glass fiber reinf orced polyester plastics. Subsequently, anex terior acrylic enamel color coat is generally applied. Two types ofprimers are defined as follows:Type I Conductive pr
4、imer - re commended when enamel color coat is appliedwith electrostatic spray equipment.Type II Non-conductive primer - recommended when enamel color coat isapplied with conventional spray equipment.3. REQUIREMENTSThe material shall meet all detailed requirements of this specification.Tests shal l b
5、e made on the basis of comparison with approved productionmaterial, applied and tested under identical conditions.3.1 COMPOSITION3.1.1 Non-Volatile, min 30 %(FLTM BI 102-01)3.2 PHYSICAL PROPERTIES3.2.1 Weight per Volume, min 0.90 kg/L(ASTM D 1475)3.2.2 Viscosity40 - 70 s(FLTM BI 111-01)3.2.3 Stabili
6、ty(FLTM BI 102-03)The material shall not gel, settle hard or increase inviscosity in excess of 10 s.ENGINEERING MATERIAL SPECIFICATIONESB-M6J106-AESB-M6J106-BWP 3948-b Page 2 of 5 3.3 PREPARATION OF TEST PANELS(FLTM BI 103-02, Method “C“, with thefollowing exceptions)Pan els: Glass fiber reinforced
7、polyester plastic panels of anyconvenient size. A smooth surface with no glass pattern, pits or blowholes i s required. Wipe panels with isopropanol, acetone or MEKbefore applying primer.Prim er: Reduce to 22 +/- 2 s #4 Ford Cup using 25 - 35 % M14J245Xylol. Spray 21 - 30 micrometre dry film thickn
8、ess. Bake 45 minutesat 149 C. Sand 1/2 of panel.Color Coat: ESB-M32J100, Color 1724-A Black (JASAXXA).3.4 APPEARANCE3.4.1 ColorType I Black or grayType II Gray* or black*No da rker than master color panel on file in the BodyMaterial Engineering Department.3.4.2 LevelingThe pr imer film shall level w
9、ith a minimum of orange peel.The surface of the material under test shall be equal to orbe tter than current approved production material forsmoothness when applied and baked under identica l conditions.3.4.3 HoldoutTh ere shall be no evidence of dulling or strike-in whenenamel color coat is ap plie
10、d over sanded and unsanded primersurfacer, and no difference in gloss of the color coatbetween sanded and unsanded primer. There shall be noprominence of sand scratches.3.4.4 Gloss(FLTM BI 110-01, 60 deg Glossmeter)ESB-M6J106-A (Types I & II), max 10ESB-M6J106-B (Type I), min 60(Type II), min 75ENGI
11、NEERING MATERIAL SPECIFICATIONESB-M6J106-AESB-M6J106-BWP 3948-b Page 3 of 5 3.5 FILM PROPERTIES3.5.1 Hand Sanding CharacteristicsThe primer, when applied and baked as outlined in para 3.3,shall w ater sand (using a new sheet of 400 grit paper foreach pan el) smoothly without clogging the paper and w
12、ith aminimum of sand scratch es. The material shall be equivalentin all respects to current approved production p rimer appliedand tested under identical conditions.3.5.2 Production TrialFi nal approval of sanding characteristics shall be made bythe using manufacturing division of the material or pa
13、intedpart on the basis of a shop trial under productioncon ditions. Disposition on conductivity of Type I primershall also be made.3.5.3 Adhesion(FLTM BI 106-01)Test material versus current approved production primer. Bothprimer adhesion to plastic and enamel adhesion to sanded orunsanded primer sha
14、ll be satisfactory, with no chipping.3.5.4 Electrical Conductivity (Type I), min 125(Ransburg Electro-Coating Corp. Model236 Sprayability Meter or Equivalent)3.6 RESISTANCE PROPERTIES3.6.1 Chip Resistance(FLTM BI 7-1)Prepare according to para 3.3 using current approvedpro duction primer for comparis
15、on, and ESB-M33J100 qualitycolor coat.3.6.2 Water Immersion, min 240 h(FLTM BI 104-01)No blistering or loss of gloss.3.6.3 Florida ExposurePanels, prepared as in para 3.3, scribed with an “X“ to bareplastic and exposed in the Miami, Florida area at 5 degfacing south for 12 months, shall show no blis
16、tering,peeling, checking or brittleness.ENGINEERING MATERIAL SPECIFICATIONESB-M6J106-AESB-M6J106-BWP 3948-b Page 4 of 5 3.7 STATISTICAL PROCESSSupplie rs must conform to the requirements of Ford Quality SystemStand ard Q-101. A mutually acceptable Control Plan as describedtherein is required for mat
17、erial/source approval. Appropriatestatist ical tools must be used to analyze process/product data sothat variation in the final product is continuously reduced.3.8 SUPPLIERS RESPONSIBILITYAll materials supplied to this specification must be equivalent inal l characteristics to the material upon whic
18、h approval wasoriginally granted.Pri or to making any change in the properties, composition,constr uction, color, processing or labeling of the materialorig inally approved under this specification, whether or not suchchange s affect the materials ability to meet the specificationrequir ements, the
19、Supplier shall notify Purchasing, Toxicology andthe affected Materials Engineering activity of the proposed changesand obtain the written approval of the Materials Engineeringactivity. Test data, t est samples and a new code identification areto be submitted with the request.Substance restrictions i
20、mposed by law, regulations or Ford, apply tothe materials addressed by this document. The restrictions aredefined in Engineering Material Specification WSS-M99P9999-A1.4. APPROVAL OF MATERIALSMat erials defined by this specification must have prior approval by theresponsible Materials Engineeri ng a
21、ctivity. Suppliers desiring approval ofthe ir materials shall first obtain an expression of interest from theaffec ted Purchasing, Design and Materials Engineering activity. Uponrequest, the Supplier shall submit to the affected Materials Engineeringactivity a completed copy of their laboratory test
22、 reports, signed by aqualified and authorized representative of the test faci lity, demonstratingful l compliance with all the requirements of this specification (testresults, not nominal values), the material designation a nd code number, andtes t specimens for Ford evaluation. Fords engineering ap
23、proval of amateri al will be based on its performance to this specification and on anassessment of suitability for i ntended processes and/or applications. Uponapprov al, the material will be added to the Engineering Material ApprovedSource List.5. GENERAL INFORMATIONThe information below is provide
24、d for clarification and assistance inmeeting the requirements of this specification.5.1 FLASH POINT, min 27 C(ASTM D 92)ENGINEERING MATERIAL SPECIFICATIONESB-M6J106-AESB-M6J106-BWP 3948-b Page 5 of 5 5.2 FLAMMABILITYThis material represent s a potential fire hazard. The ManufacturingEngineering Depa
25、rtment shall notify both the Plant Security and theSafety Units of its pre sence in the Plant to assure that proper fireprecautions are provided. The location in which it is used or storedshall be included in the notification.5.3 TOXICITYThe material shall be non-toxic and shall not cause skin rash
26、orirritation (dermatitis) to exposed handlers in normal productionoperations.Benzene and chlorinated hydrocarbon solvents are considered toxic andtheir use is strictly prohibited in compounding material to thisspecification.5.4 ZINC REACTIVITYThis material is highly zinc reactive and, therefore, should not bestored or used in galvanized or zinc-lined tanks or equipment.5.5 APPLICABLE SPECIFICATIONSSubstrate ESB-M3D101 or as specified onengineering drawing.Primer ESB-M6J106Enamels ESB-M30J100 or ESB-M32J 100 quality
