FORD WSD-M2D420-A2-2009 RUBBER POLYCHLOROPRENE (CR) LOW TEMPERATURE FLEXIBLE 60 IRHD HARDNESS TO BE USED WITH FORD WSS-M99P1111-A 《IRHD硬度为60的柔性耐低温聚氯丁烯(CR)橡胶 与标准FORD WSS-M99P1111.pdf

上传人:吴艺期 文档编号:749863 上传时间:2019-01-14 格式:PDF 页数:3 大小:26.84KB
下载 相关 举报
FORD WSD-M2D420-A2-2009 RUBBER POLYCHLOROPRENE (CR) LOW TEMPERATURE FLEXIBLE 60 IRHD HARDNESS  TO BE USED WITH FORD WSS-M99P1111-A  《IRHD硬度为60的柔性耐低温聚氯丁烯(CR)橡胶  与标准FORD WSS-M99P1111.pdf_第1页
第1页 / 共3页
FORD WSD-M2D420-A2-2009 RUBBER POLYCHLOROPRENE (CR) LOW TEMPERATURE FLEXIBLE 60 IRHD HARDNESS  TO BE USED WITH FORD WSS-M99P1111-A  《IRHD硬度为60的柔性耐低温聚氯丁烯(CR)橡胶  与标准FORD WSS-M99P1111.pdf_第2页
第2页 / 共3页
FORD WSD-M2D420-A2-2009 RUBBER POLYCHLOROPRENE (CR) LOW TEMPERATURE FLEXIBLE 60 IRHD HARDNESS  TO BE USED WITH FORD WSS-M99P1111-A  《IRHD硬度为60的柔性耐低温聚氯丁烯(CR)橡胶  与标准FORD WSS-M99P1111.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2009 09 17 N-STATUS Use industry standard C. Mracna, NA 2005 01 25 Revised Removed Inactive A1; Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.10, 3.11, 4 1990 03 30 Released C10067638 B. Hennessey Printed copies are uncontrolled Copyright 2009, Ford

2、Global Technologies, LLC Page 1 of 3 RUBBER, POLYCHLOROPRENE (CR) WSD-M2D420-A2 LOW TEMPERATURE FLEXIBLE, 60 IRHD HARDNESS RUBBER, POLYCHLOROPRENE (CR) WSD-M2D420-A3 LOW TEMPERATURE FLEXIBLE, 70 IRHD HARDNESS NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by these specifications are Po

3、ly-Chloroprene Rubbers with nominal hardnesses of 60 IRHD (Suffix A2) and 70 IRHD (Suffix A3) respectively. 2. APPLICATION These specifications were released originally for materials used for drive shaft dust boots where low temperature flexibility down to -40 C and high tear strength are required.

4、3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 MATERIAL TESTING 3.4.1 Preparation of Test Specimens Whenever possible, all test specimens shall

5、be die-cut from the finished parts. When not feasible, specimens cut from molded test sheets manufactured from the same material and with equivalent cure to molded parts are recommended. The test sheets shall have the following dimensions: 150 x 150 mm, min x 2.0 +/- 0.2 mm 3.5 ORIGINAL PROPERTIES A

6、2 A3 3.5.1 Hardness, 55 - 65 65 - 75 International (ASTM D 1415) 3.5.2 Hardness, Durometer A 55 - 65 65 - 75 (ISO 868/ASTM D 2240, instantaneous, plied-up specimen. Hand held durometers shall not be used) ENGINEERING MATERIAL SPECIFICATIONWSD-M2D420-A2/A3 Printed copies are uncontrolled Copyright 20

7、09, Ford Global Technologies, LLC Page 2 of 3 A2 A3 3.5.3 Tensile Strength, MPa, min 12 15 (ISO 37/ASTM D 412, Die C) 3.5.4 Elongation at Break, %, min 300 240 (Test Method according to para 3.5.3) 3.5.5 Modulus at 100% 2.4 4.5 4.6 7.0 Elongation, MPa (Test Method according to para 3.5.3) 3.5.6 Tear

8、 Strength, kN/m, min 15 20 (ISO 34, Method B, procedure (a)/ASTM D 624, Die C) 3.5.7 Brittleness Point, max -40 C (ISO 812, Type B specimen/ ASTM D 2137, Method A) 3.5.8 Ozone Resistance, max Rating 0 (FLTM BP 101-01, Procedure A) 3.5.9 Compression Set, max 30% (ISO 815/ASTM D 395, Method B, except

9、25% compression, plied-up specimens, 22 h at 100 +/- 2 C) 3.6 HEAT AGED (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 168 h at 100 +/- 2 C) 3.6.1 Hardness Change, max +15 3.6.2 Tensile Strength Change, max -15% 3.6.3 Elongation Change, max -35% 3.6.4 Visual Evaluation No surface tackiness or cracks

10、 when folded flat against itself. 3.7 HEAT AGED (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 80 +/- 2 C) 3.7.1 Hardness Change, max +15 3.7.2 Tensile Strength Change, max -15% 3.7.3 Elongation Change, max -35% ENGINEERING MATERIAL SPECIFICATIONWSD-M2D420-A2/A3 Printed copies are uncontro

11、lled Copyright 2009, Ford Global Technologies, LLC Page 3 of 3 3.7.4 Visual Evaluation No surface tackiness or cracks when folded flat against itself. 3.8 IMMERSION IN OIL No. 1 (ISO 817/ASTM D 471, 168 h at 100 +/- 2 C) 3.8.1 Hardness Change, max +20 3.8.2 Tensile Strength Change, max -20% 3.8.3 El

12、ongation Change, max -40% 3.8.4 Volume Change -15 to +5% 3.8.5 Visual Evaluation No surface tackiness or cracks when folded flat against itself. 3.9 IMMERSION IN OIL No. 3 (ISO 1817/ASTM D 471, 168 h at 100 +/- 2 C) 3.9.1 Hardness Change, max -35 3.9.2 Tensile Strength Change, max -60% 3.9.3 Elongation Change, max -50% 3.9.4 Volume Change +70% 3.9.5 Visual Evaluation No surface tackiness or cracks when folded against itself.

展开阅读全文
相关资源
猜你喜欢
  • CP 65 Pt 2-1996 CODE OF PRACTICE FOR Structural use of concrete Part 2  Special circumstances《混凝土结构使用规范  第2部分:特殊环境》.pdf CP 65 Pt 2-1996 CODE OF PRACTICE FOR Structural use of concrete Part 2 Special circumstances《混凝土结构使用规范 第2部分:特殊环境》.pdf
  • CP 67 Pt 2-1999 CODE OF PRACTICE FOR Cleaning and surface repair of buildings Part 2  Concrete and concrete masonry《建筑物清洁及外表面的修缮规范 第2部分:混凝土和混凝土砖石工程》.pdf CP 67 Pt 2-1999 CODE OF PRACTICE FOR Cleaning and surface repair of buildings Part 2 Concrete and concrete masonry《建筑物清洁及外表面的修缮规范 第2部分:混凝土和混凝土砖石工程》.pdf
  • CP 69-1998 Code of Practice for Microfilming of documents on 16 mm black and white silver-gelatin type microfilm planetary and rotary camera filming- Operating procedures《16毫米银胶质黑白.pdf CP 69-1998 Code of Practice for Microfilming of documents on 16 mm black and white silver-gelatin type microfilm planetary and rotary camera filming- Operating procedures《16毫米银胶质黑白.pdf
  • CP 7 Erratum 1-1999 CODE OF PRACTICE FOR THE STRUCTURAL USE OF TIMBER ERRATUM NO 1《建筑用木材规范 错字勘误表1》.pdf CP 7 Erratum 1-1999 CODE OF PRACTICE FOR THE STRUCTURAL USE OF TIMBER ERRATUM NO 1《建筑用木材规范 错字勘误表1》.pdf
  • CP 7 Erratum 2-1999 CODE OF PRACTICE FOR THE STRUCTURAL USE OF TIMBER ERRATUM NO 2《建筑用木料的使用规范  错字勘误表2》.pdf CP 7 Erratum 2-1999 CODE OF PRACTICE FOR THE STRUCTURAL USE OF TIMBER ERRATUM NO 2《建筑用木料的使用规范 错字勘误表2》.pdf
  • CP 70-1998 Code of Practice for Microfilming of technical drawings and other drawing office documents on 35 mm black and white silver-gelatin type microfilm planetary camera filmin.pdf CP 70-1998 Code of Practice for Microfilming of technical drawings and other drawing office documents on 35 mm black and white silver-gelatin type microfilm planetary camera filmin.pdf
  • CP 71-1998 Code of Practice for Quality control inspection of 16 mm and 35 mm black and white silver-gelatin type microfilm《16mm和35mm银胶质黑白微缩胶片的质量控制检查规范》.pdf CP 71-1998 Code of Practice for Quality control inspection of 16 mm and 35 mm black and white silver-gelatin type microfilm《16mm和35mm银胶质黑白微缩胶片的质量控制检查规范》.pdf
  • CP 72-1998 Code of Practice for Microfilming of newspapers on 35 mm black and white silver-gelatin type microfilm planetary camera filming-Operating procedures《35毫米银胶质黑白微缩胶片上的新闻微缩影.pdf CP 72-1998 Code of Practice for Microfilming of newspapers on 35 mm black and white silver-gelatin type microfilm planetary camera filming-Operating procedures《35毫米银胶质黑白微缩胶片上的新闻微缩影.pdf
  • CP 73-1998 CODE OF PRACTICE FOR Design of concrete structures for retaining aqueous liquids《拦水用混凝土结构的设计规范》.pdf CP 73-1998 CODE OF PRACTICE FOR Design of concrete structures for retaining aqueous liquids《拦水用混凝土结构的设计规范》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1