FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf

上传人:hopesteam270 文档编号:750768 上传时间:2019-01-14 格式:PDF 页数:5 大小:138.59KB
下载 相关 举报
FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf_第1页
第1页 / 共5页
FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf_第2页
第2页 / 共5页
FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf_第3页
第3页 / 共5页
FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf_第4页
第4页 / 共5页
FORD WSK-M4D743-A-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 40% GLASS FIBER REINFORCED MOLDING COMPOUND  TO BE USED WITH FORD WSS-M99P1111-A  (Use WSB-M4D678-A)《40%玻璃纤维增强的受热稳定的聚酰胺66成型.pdf_第5页
第5页 / 共5页
亲,该文档总共5页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 04 N-STATUS Replaced by WSB-M4D678-A A. Reaume/M. Masserant 2006 01 13 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.8, 3.9 & 4 1990 03 01 Released C/01031533 M. Siewert Printed copies are uncontrolled Copyright 2006, Ford Global Technolog

2、ies, LLC Page 1 of 5 POLYAMIDE (PA) 66, HEAT STABILIZED WSK-M4D743-A 40% GLASS FIBER REINFORCED MOLDING COMPOUND NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a heat stabilized glass fiber reinforced polyamide 66 molding compound. 2. APPLICATION This specificat

3、ion was released originally for material used for parts of cable throttle control. NOTICE: This material absorbs and retains moisture. Part design and tolerances must accommodate changes in part dimensions and physical properties due to moisture absorption or loss in the service/assembly environment

4、 3. REQUIREMENT Material specification requirements are to be used for initial qualification of materials. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.3 CONDI

5、TIONING AND TEST CONDITIONS All test values indicated herein are based on material and specimens with moisture content not exceeding 0.2% (test according to ISO 960, Method B/ASTM D 789). All test materials immediately after processing have to be sealed in containers that are impermeable to water va

6、por. If the moisture content exceeds 0.2%, condition the material for a minimum of 16 h at 40 - 50 C at a reduced pressure below 133 Pa. Conduct tests in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity. Individual specimens shall not be removed from closed containers until imme

7、diately before testing. 3.4 MOLDING COMPOUND 3.4.1 Glass Fiber Content 37.5 - 42.5% (ISO 3451/4, test temperature 600 +/ 25 C, test portion 1 g) 3.4.2 Melt Temperature 250 - 265 C (ISO 1218, Method B/ASTM D 789) ENGINEERING MATERIAL SPECIFICATIONWSK-M4D743-A Printed copies are uncontrolled Copyright

8、 2006, Ford Global Technologies, LLC Page 2 of 5 3.5 MOLDED TEST SPECIMEN 3.5.1 Preparation of Test Specimens Unless otherwise specified all tests shall be carried out on injection molded one-end gated test specimens. The following dimensions are required: A. 150 min x 10 x 4.0 +/- 0.2 mm (Tensile B

9、ar, ISO 3167) B. 120 x 10 x 4.0 +/- 0.2 mm Specimens with shorter dimensions shall be cut from the center portion of the test specimen A and/or B. The specimens shall be prepared according to ISO 294. No annealing allowed. 3.5.2 Density 1.44 - 1.48 g/cm3(ISO 1183, Method A/ASTM D 792, Method A1) 3.5

10、3 Tensile Strength at Max Load, min 190 MPa (ISO R 527/ASTM D 638M, 150 x 10 x 4.0 +/- 0.2 mm specimen, 5 mm/minute test speed) 3.5.4 Flexural Modulus, min 9.0 GPa (ISO 178/ASTM D 790M, Method I, Procedure A, 80 x 10 x 4.0 +/- 0.2 mm specimen, 64 mm support span) 3.5.5 Shear Modulus at 23 C 1.67 -

11、2.79 GPa (ASTM D 4065, forced constant amplitude, fixed frequency of 1 Hz +/- 15%, strain level below 1%. Specimen approx. 60 x 10 x 4.0 +/- 0.2 mm cut from the center of specimen A. Specimen length between clamps 35 - 40 mm. Soak time at each temperature interval - 3 minutes minimum). Additionally,

12、 a Shear Modulus vs. Temperature curve shall be plotted for -50 to +240 C temperature range, at 5 C minimum intervals. The plotted curve must be within tolerance range shown on page 5. 3.5.6 Impact Strength, Izod, min (ISO 180, Method A/ASTM D 256, Method A, 63.5 x 10 x 4.0 +/- 0.2 mm specimen, 10 s

13、pecimens for each test) 3.5.6.1 At 23 +/- 2 C 10 kJ/m23.5.6.2 At -40 +/- 2 C 9 kJ/m2The test specimens must be conditioned for minimum of 6 h at the above specified temperature prior to impact test. Low temperature testing shall be done within the cold box, if not possible, test can be conducted out

14、side, but within 5 s. ENGINEERING MATERIAL SPECIFICATIONWSK-M4D743-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 5 3.5.7 Heat Deflection Temperature, min (ISO 75/ASTM D 648, 120 x 10 x 4.0 +/- 0.2 mm specimen) 3.5.7.1 At 1.82 MPa 240 C 3.5.7.2 At 0.45 MPa

15、250 C 3.5.8 Heat Aging Performance (ISO 188/ASTM D 573, 150 +/- 50 air changes/h, 1000 h at 140 +/- 2 C. After heat aging test specimens are to be conditioned in a desiccator for 3 - 5 h at 23 +/- 2 C. Unaged property values shall be determined at the time of the aged properties determination) 3.5.8

16、1 Impact Strength, Izod Change +/- 25% (Test Method per para 3.5.6.1, specimens to be notched before heat aging) 3.6 FLAMMABILITY (ISO 3795) Burn Rate, max 100 mm/minute The specimen size required for material approval is 355 x 100 x 1.0 +/- 0.1 mm with a smooth surface. 3.7 FOGGING (FLTM BO 116-03

17、) Fog Number, min 60 Formation of excessive amounts of clear film or droplets is cause for rejection. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 COEFFICIENT OF LINEAR THERMAL EXPANSION 2 - 4-5

18、/ C (ASTM D 696) 5.2 MOLD SHRINKAGE (ISO 2577, approx. 150 x 100 x 3.2 +/- 0.2 mm injection molded specimen) 5.2.1 Molding Shrinkage After 48 h at 23 +/- 2 C 0.2 - 1.4% ENGINEERING MATERIAL SPECIFICATIONWSK-M4D743-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 4

19、 of 5 5.2.2 Post Shrinkage (Separate specimens required for each test) After 48 h at 80 C 0.01 - 0.05% After 30 minutes at 120 C 0.01 - 0.09% 5.3 WATER ABSORPTION 0.6 - 1.0% (ISO 62, 24 h/ASTM D 570, 24 h, 50 +/- 1 mm diameter, 3.2 +/- 0.2 mm thick specimen) 5.4 IMPACT STRENGTH, IZOD, min (ISO 180,

20、Method A/ASTM D 256, Method A, 63.5 x 10 x 4.0 +/- 0.2 mm specimen, 10 specimens minimum) 5.4.1 After Moisture Conditioning 19 kJ/m2The notched specimens shall be immersed for 48 h in distilled water at 50 +/- 1 C and subsequently conditioned for 1 h at 23 +/- 2 C and 50 +/- 5% relative humidity prior to test and tested under the same conditions within 1 h. ENGINEERING MATERIAL SPECIFICATIONWSK-M4D743-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 5 of 5

展开阅读全文
相关资源
猜你喜欢
  • DIN EN 6059-601-2014 Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 601 Open and close German and English version EN 6059-601 2014《航空航.pdf DIN EN 6059-601-2014 Aerospace series - Electrical cables installation - Protection sleeves - Test methods - Part 601 Open and close German and English version EN 6059-601 2014《航空航.pdf
  • DIN EN 606-2004 Bar coding - Transport and handling labels for steel products German version EN 606 2004《条形码 钢产品的运输和处理标签》.pdf DIN EN 606-2004 Bar coding - Transport and handling labels for steel products German version EN 606 2004《条形码 钢产品的运输和处理标签》.pdf
  • DIN EN 6069-2011 Aerospace series - Rivet 100 reduced flush head close tolerance - Inch series German and English version EN 6069 2009《航空航天系列 紧公差100缩减埋头铆钉 英制系列 德文和英文版本EN 6069-2009》.pdf DIN EN 6069-2011 Aerospace series - Rivet 100 reduced flush head close tolerance - Inch series German and English version EN 6069 2009《航空航天系列 紧公差100缩减埋头铆钉 英制系列 德文和英文版本EN 6069-2009》.pdf
  • DIN EN 607-2005 Eaves gutters and fittings made of PVC-U - Definitions requirements and testing German version EN 607 2004《未增塑聚氯乙烯制屋檐沟和附件 定义、要求和检验》.pdf DIN EN 607-2005 Eaves gutters and fittings made of PVC-U - Definitions requirements and testing German version EN 607 2004《未增塑聚氯乙烯制屋檐沟和附件 定义、要求和检验》.pdf
  • DIN EN 6072-2011 Aerospace series - Metallic materials - Test methods - Constant amplitude fatigue testing German and English version EN 6072 2010《航空航天系列 金属材料 试验方法 横幅疲劳试验 德文版本和英文版本.pdf DIN EN 6072-2011 Aerospace series - Metallic materials - Test methods - Constant amplitude fatigue testing German and English version EN 6072 2010《航空航天系列 金属材料 试验方法 横幅疲劳试验 德文版本和英文版本.pdf
  • DIN EN 6075-2017 Aerospace series - Static seal elements O-Ring ethylene-propylene moulded phosphate ester resistant (- 55 C to 107 C) - Inch series German and English version EN 6.pdf DIN EN 6075-2017 Aerospace series - Static seal elements O-Ring ethylene-propylene moulded phosphate ester resistant (- 55 C to 107 C) - Inch series German and English version EN 6.pdf
  • DIN EN 6076-2017 Aerospace series - Static seal elements O-Ring for straight thread tube fitting boss ethylene-propylene moulded phosphate ester resistant (-55 C to 107 C) - Inch s.pdf DIN EN 6076-2017 Aerospace series - Static seal elements O-Ring for straight thread tube fitting boss ethylene-propylene moulded phosphate ester resistant (-55 C to 107 C) - Inch s.pdf
  • DIN EN 6080-2016 Aerospace series - Rivet 100 normal flush head close tolerance - Inch series German and English version EN 6080 2016《航空航天系列 100紧公差正常平头铆钉 英制系列 德文和英文版本EN 6080-2016》.pdf DIN EN 6080-2016 Aerospace series - Rivet 100 normal flush head close tolerance - Inch series German and English version EN 6080 2016《航空航天系列 100紧公差正常平头铆钉 英制系列 德文和英文版本EN 6080-2016》.pdf
  • DIN EN 6081-2016 Aerospace series - Rivet universal head close tolerance - Inch series German and English version EN 6081 2016《航空航天系列 100紧公差通用头铆钉 英制系列 德文和英文版本EN 6081-2016》.pdf DIN EN 6081-2016 Aerospace series - Rivet universal head close tolerance - Inch series German and English version EN 6081 2016《航空航天系列 100紧公差通用头铆钉 英制系列 德文和英文版本EN 6081-2016》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1