1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2010 01 06 Revised Revised 3.3, 3.7, 3.12, 3.14, 3.15, 3.16.1, 3.16.2, Inserted 3.4.3, 3.4.4, 3.4.5 Deleted 3.13 para 3.1, 3.20 & 4 deleted 1996 03 29 Activated NE01-E-10127076-166 D. Walter Printed copies are uncontrolled Copyright 2010, Ford
2、 Global Technologies, LLC Page 1 of 3 FUEL, DIESEL, INITIAL FILL, ARGENTINA WSS-M4C117-A 1. SCOPE The material defined by this specification is a well-refined middle distillate petroleum product containing normal commercial additives. 2. APPLICATION This specification was released originally for mat
3、erial used as initial fill fuel for diesel engines in passenger cars and trucks. This material is not specifically intended for use in certification testing. It may be used for engine hot test, mileage accumulation or general fueling. 3. REQUIREMENTS This material must be produced using current refi
4、nery practices for commercial diesel and in addition to the requirements of this specification, must also meet all pertinent local requirements including climatic grades. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIAL Material suppliers and part producers must conform to the Companys Standard Req
5、uirements For Production Materials (WSS-M99P1111-A). 3.2 CETANE RATING 3.2.1 Cetane Number 51 min (ISO 5165 / ASTM D 613) 3.2.2 Cetane Index 48 min (ISO 4264 / ASTM D 4737) 3.3 SULPHUR 50 mg/kg max (ASTM D 1552 / D 2622 / D 4294 / D 5453) ENGINEERING MATERIAL SPECIFICATIONWSS-M4C117-A Printed copies
6、 are uncontrolled Copyright 2010, Ford Global Technologies, LLC Page 2 of 3 3.4 COMPOSITION, max 3.4.1 Water content 200 mg/kg (ISO 12937/ASTM D 1744) 3.4.2 Hydrocarbon Types Report (ISO 3837/ASTM D 1319) 3.4.3 Total contamination 24 mg/kg (EN 12662) 3.4.4 Polycyclic Aromatic Hydrocarbons 11% mass (
7、IP 391:1995/EN12916) 3.4.5 FAME (Biodiesel) Not allowed 3.5 DISTILLATION RANGE, max (ISO 3405/ASTM D 86) Temperature, C Initial boiling point Report 10% vol recovery at, Report 50% vol recovery at, 300 95% vol recovery at, 365 Final boiling point Report 3.6 DENSITY 0.820 - 0.860 kg/L (ISO 3675/ASTM
8、D 1298, 15.0 C) 3.7 OXIDATION STABILITY, total insolubles 2.5 mg/100 mL max (ISO 12205/ASTM D 2274) 3.8 CALORIFIC VALUE, gross Report (ASTM D 240) 3.9 CORROSION 3.9.1 Copper Tarnish, max 1 b (ISO 2160/ASTM D 130, 3 h at 100 +/- 1 C) 3.9.2 Rust Prevention, max Ligth (ISO DP 7120/ASTM D 665, Procedure
9、 B, 30 minutes) 3.10 FLASHPOINT 48 C min (ISO 2719/ASTM D 93) 3.11 KINEMATIC VISCOSITY 2.00 - 4.50 mm2/s (ISO 3104/ASTM D 445, 40 C) 3.12 LUBRICITY at 60C 400 m max (ISO 12156-1/ASTM D6079 (HFRR) ENGINEERING MATERIAL SPECIFICATIONWSS-M4C117-A Printed copies are uncontrolled Copyright 2010, Ford Glob
10、al Technologies, LLC Page 3 of 3 3.14 CARBON RESIDUE 0.20% max (ISO 6615/ASTM D 189/ASTM D 524, 10% distillation residue) 3.15 WATER REACTION, fuel layer only 1, slight haze max (ISO 6250/ASTM D 1094) 3.16 COLD TEMPERATURE PROPERTIES 3.16.1 Cloud Point, max 7 C (Oct Mar) (ISO 3015/ASTM D 2500) 5 C (
11、Apr May) 3 C (Jun Sep) 3.16.2 Cold Filter Plugging Point, max 0 C (Oct Mar) (EN 116/ASTM D 6371) 1 C (Apr May) -3 C (Jun Sep) 3.17 ODOR The material shall have the usual characteristic odor of diesel fuel. There shall be no obvious foreign odors. 3.18 ADDITIVES The material shall contain normal comm
12、ercial additives. Additives which specifically enhance the cetane number are not permitted. A commercial corrosion inhibitor package is normally required to pass paragraph 3.10.2 Rust Prevention and paragraph 3.15 Water Reaction. 3.19 DYESTUFF The material shall be dyed in accordance with Customs an
13、d Excise requirements. 3.20 ASH 0.01% mass max (ISO 6245/ASTM D 482) 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 FLAMMABILITY This material represents a potential fire hazard. The Manufacturing
14、 Engineering Department or other responsible activity shall notify both the Security and Safety Units of its presence to assure that proper fire precautions are provided. The location in which it is used or stored shall be included in the notifications. 5.2 SAMPLING AND SUBMISSION OF SAMPLES (ISO 3170/3171, ASTM D 4057/D 4177) 5.3 Quality Control records must be made available to the responsible product engineering office upon request.
