FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED TO BE USED WITH FORD WSS-M99P1111-A .pdf

上传人:eastlab115 文档编号:754072 上传时间:2019-01-14 格式:PDF 页数:15 大小:142.04KB
下载 相关 举报
FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第1页
第1页 / 共15页
FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第2页
第2页 / 共15页
FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第3页
第3页 / 共15页
FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第4页
第4页 / 共15页
FORD WSS-M8P3-E1-2014 PERFORMANCE FLEXIBLE POLYMERIC FILM INTERIOR QUALITY UNSUPPORTED  TO BE USED WITH FORD WSS-M99P1111-A  .pdf_第5页
第5页 / 共15页
点击查看更多>>
资源描述

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 5 2014 06 18 Editorial See Summary of Revisions D. Murtonen, NA 2014 02 25 Editorial See Summary of Revision D. Murtonen, NA 2009 04 14 Activated M Dumitrescu, FNA J Williams, FOE Controlled document at www.MATS Copyright 2014, Ford Glob

2、al Technologies, LLC Page 1 of 15 PERFORMANCE, FLEXIBLE POLYMERIC FILM, INTERIOR WSS-M8P3-E1 QUALITY, UNSUPPORTED PERFORMANCE, FLEXIBLE POLYMERIC FILM, INTERIOR WSS-M8P3-E2 QUALITY, SUPPORTED PERFORMANCE, FLEXIBLE POLYMERIC FILM, INTERIOR WSS-M8P3-E3 QUALITY, SUPPORTED PLUS FOAM LAMINATE AND/OR BACK

3、ING MATERIAL 1. SCOPE These specifications define the performance requirements for interior unsupported and supported polymeric films, supported films laminated to foam, and the material requirements for the foam. 2. APPLICATION These specifications were released originally for materials used as int

4、erior trim coverings for seats, door panels, headlining and other applications. WSS-M8P3-E1 Unsupported WSS-M8P3-E2 Supported WSS-M8P3-E3 Supported plus Foam Laminate and/or Backing Material 3. REQUIREMENTS In addition to the requirements listed herein, the face flexible polymeric film and/or foam l

5、aminate shall meet all requirements of the applicable M2F or M2D material specifications. Laminated composites must demonstrate compliance to this specification for all material lamination combinations utilized. Seat trim cover assemblies or interior trim panels employing these materials must also m

6、eet the engineering requirements of the related Ford Motor performance specifications (e.g., WSS-M15P4-F or latest, System Design Specifications (SDS), seat assembly, headrest, etc.), along with any other requirements shown on the engineering drawing. The material specification shall take precedence

7、 over the performance specification, for any requirement that differs from the performance specification. 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements for Production Materials (WSS-M99P1111-A). 3.1.1 Vehic

8、le Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/latest. ENGINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 2 of 15 3.2 SAMP

9、LE SELECTION Testing must be conducted on materials at each prototype and production build phase unless specified otherwise by Ford Engineering. See Table 1 for DV/PV testing. 3.3 CONSTRUCTION All information must be provided in Table 2- MATERIAL SUPPLIER SPECIFICATION INFORMATION SHEET which will b

10、e included in the Construction Package. 3.4 APPEARANCE (FLTM BI 109-O1) The color, pattern, and finish shall match the approved Design Center master sample, or shall be as specified on the engineering drawing. 3.4.1 Instrumental Color Readings (SAE J1767) Instrumental color readings are required. Vi

11、sual evaluation will take precedence over instrumental readings in cases of dispute. No production batch shall deviate by more than 0.85 Delta E from the designated color master nor from the preceding production batch when measured in accordance with SAE J1767. 3.5 WEIGHT, g/m2 Report Range (ASTM D

12、751, sample method) 3.6 FINISHED THICKNESS, mm Report Range (ASTM D751) 3.7 RESISTANCE TO FLEXING* (*Contact Materials Engineering for agreement on method selection for Resistance to Flexing) 3.7.1 Resistance to W flex No evidence of (FLTM BN 102-02) crazing, lifting, peeling or crackingSeating Mate

13、rials, Trim Materials Original, 100,000 cycles Rating 1 max After Heat Aging per para 3.12, 30,000 cycles Rating 1 max After Fade per para 3.11.1, 30,000 cycles Rating 1 max Commercial Vehicle and Truck Seating Applications Original Material, 500,000 cycles Rating 1 max After Heat Aging per para 3.1

14、2, 100,000 cycles Rating 1 max After Fade per para 3.11.1, 100,000 cycles Rating 1 max 3.7.2 Resistance to Bally flex (FLTM BN 162-01) Test three specimens in each direction to the number of cycles specified below. Retain tested specimens and submit for evaluation by Materials Engineering. Seating m

15、aterials, Trim materials Original, 100,000 cycles Rating 1 max Original, 200,000 cycles Rating 2 max After Heat Aging per para 3.12, 30,000 cycles Rating 1 max ENGINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 3 of 15 3.7.2 Resistance to Bally fl

16、ex (cont) (FLTM BN 162-01) Commercial Vehicle and Truck Seating Applications Original, 300,000 cycles Rating 1 max Original, 400,000 cycles Rating 2 max After Heat Aging per para 3.12, 100,000 cycles Rating 1 max 3.8 COLD CRACKING RESISTANCE 3.8.1 Cold Flexibility Shall remain flexible (FLTM BN 102-

17、01) and not crack when bent 180 around Original (as received) after 24 hrs at-30 +/- 2 C mandrel. Aged 7 days at 100 +/-2 C and 24 hrs at -30 +/- 2 C Note: the mandrel diameter should be 6.4 mm or as specified in the Material Specification 3.8.2 Low Temperature Impact (coated fabrics) (FLTM BN 128-0

18、1, 4.05J impact) Original (as received) after 24 hrs at-30 +/- 2 C No visible cracking After 7 days at 100+/- 2 C and 24 hrs at -30 +/- 2 C No visible cracking 3.9 RESISTANCE TO ABRASION* (*Contact Materials Engineering for agreement on method selection for Resistance to Abrasion) 3.9.1 Taber Abrasi

19、on (SAE J948, CS-10 wheels) Headlining Materials 500 g load, 150 cycles Seating Materials, Tonneau Cover 1000 g load, 1000 cyclesor higher if directed in the relevant material specification Trim Panels and Other Materials 1000 g load, 250 cycles 3.9.2 Wyzenbeek Abrasion (ASTM D4157, 3 specimens, 2.7

20、 kg tension, 40,000 cycles or higher 1.8 kg load, No 8 Duckcloth) if directed in the relevant material specification The abraded area must exhibit compatible color and appearance with the adjacent unabraded area. No loss of grain or other detrimental effects. The abrasion resistance of production ma

21、terial shall be equal to or better than the sample approved by Materials Engineering. All three specimens must pass 3.10 RESISTANCE TO SCUFFING (SAE J365, 0.9 kg load, A head) No evidence of lifting, Seating Materials, 200 cycles peeling or excessive Headlining Materials, 75 cycles scuffing. Trim Pa

22、nels and Other Materials, 200 cycles ENGINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 4 of 15 3.11 RESISTANCE TO FADE (FLTM BO 116-01, ISO 105-A02/ AATCC Evaluation Procedure 1) 3.11.1 451.2 kJ/m2 Exposure Rating 4-5 min 3.11.2 977.6 kJ/m2 Expos

23、ure Rating 4 min After exposure, the material shall show no change in color tone (hue) or gloss and shall be equal to or better than the sample approved by Materials Engineering. Any surface bloom/chalking should be easily removed with water. In addition, it must remain flexible and exhibit no crack

24、ing when bent around a 6.4 mm mandrel (face side out) after exposure. 3.12 RESISTANCE TO HEAT AGING (7 days at 100 +/- 2 C, the oven shall conform to ISO 188/ASTM E 145 Type IIA, normal oven, 150 +/- 50 air changes per hour, and provide a minimum oven space of 2 L/100 cm2 of sample size for heat exp

25、osure tests.) 3.12.1 Visual Deterioration Rating 4 min (ISO 105-A02/AATCC Evaluation Procedure 1) After exposure, the material shall show no evidence of tackiness, spewing, excessive loss of grain or exhibit staining, color tone change or change in hue in excess of required AATCC rating. Any “spotty

26、“ or non-uniform staining or discoloration shall be cause for rejection. If rating is less than 4, then the material must be tested and found to meet the requirements of 3.12.1.1 3.12.1.1 Visual Deterioration, Xenon Arc Rating 4-5 min (FLTM BO 116-01, 75.2 kJ/m2 ISO 105-A02/AATCC Evaluation Procedur

27、e 1) After exposure, the material shall show no evidence of tackiness, spewing, excessive loss of grain, or exhibit staining, color tone change or change in hue in excess of required AATCC rating. Any “spotty“ or non-uniform staining or discoloration shall be cause for rejection. 3.12.2 Volatile los

28、s, range 0 - 5% by weight 3.13 SOILING AND CLEANABILITY (FLTM BN 112-08, ISO 105-A02/AATCC Evaluation Procedure 2) Standard Soil Rating 4 min Grease Rating 4 min Coffee Rating 4 min 3.14 RESISTANCE TO CROCKING AND DYE TRANSFER 3.14.1 Resistance to Crocking (FLTM BN 107-01, AATCC Evaluation Procedure

29、 2) Dry and Wet Rating 5 min Vinyl Cleaner from FLTM BN 112-08 Rating 5 min Commercially available Glass Cleaner Rating 5 min 3.14.2 Resistance to Dye Transfer, Martindale method (ISO 26082 except use Pilling Head, ISO 105-A03/AATCC Evaluation Procedure 2, Test fabric EMPA 128, 1000 cycles) ENGINEER

30、ING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 5 of 15 Clean the surface manually using white cotton cloths moistened with the Approved Brand Vinyl Cleaner from FLTM BN 112-08. Change cloth frequently until no color transfer is visible on the cloth. a

31、fter cleaning and 30 minutes drying at room temperature Rating 4 min after cleaning and 24 hours drying at room temperature Rating 4 min . 3.14.3 Resistance to Dye Transfer, Crockmeter method (FLTM BN 112-09, AATCC Evaluation procedure 2) Before cleaning Rating 3 min after cleaning and 30 minutes dr

32、ying at room temperature Rating 4-5 min after cleaning and 24 hours drying at room temperature Rating 4-5 min 3.15 RESISTANCE TO MIGRATION STAINING AND BLOCKING (FLTM BN 103-01) No evidence of injurious exudation, adhesion (tackiness), separation, color transfer, staining, or flattening of embossing

33、 when placed face to face with itself and to unsupported white vinyl film. No staining or color transfer to white vinyl film. 3.16 SEAM FATIGUE RESISTANCE 3 mm max (FLTM BN 106-02, seating applications only) (Needle hole elongation after test). 3.17 RESISTANCE TO TEAR (Requirements are found in the

34、relevant Material Specification) 3.17.1 Unsupported Film, N/mm Report (ISO 34/ASTM D 1004 Method B, Procedure A) 3.17.2 Supported Film (fabric backing), N Report (ASTM D751,Trapezoid tear) 3.17.3 Foam Laminated Film, N Report (ASTM D751,Trapezoid tear) 3.18 BREAKING STRENGTH (Requirements are found

35、in the relevant Material Specification) 3.18.1 Unsupported Films, MPa Report (ISO 37 type 1 dumbbell/ASTM D 412, Method A, Die C) 3.18.2 Supported Films, N Report (ASTM D 751, grab method) 3.18.3 Foam Laminated Films, N Report (ASTM D 751, grab method) ENGINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/

36、E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 6 of 15 3.19 SEAM STRENGTH 350 N min (FLTM BN 119-01, except use lockstitch with (for seating 6 stitches/25 mm, 5 sample average in each applications) direction) 3.20 ADHESION 3.20.1 Coating Adhesion No removal of (FLTM BI 106-01, Method C) su

37、rface coating or vinyl film 3.20.2 Film to Backing (FLTM BN 151-05 Method A/ISO 2411) WMD and AMD 25 N/50 mm min 3.21 STRETCH AND SET, % Report (SAE J855) 3.22 STIFFNESS Report (ASTM D 747, 25 x 50 mm) 3.23 DIMENSIONAL STABILITY (SAE J883) (Requirements are found in the relevant Material Specificati

38、on) MD added 3.9.2 Wyzenbeek Abrasion Date 2011 07 26 Allowed material specifications to impose higher requirements for Tabor Abrasion (3.9) Date: 2011 04 20 Paragraph 3 -Added requirement for Performance, Vehicle Interior Environment Quality Material /Components WSS-M99P2222* Paragraph 3.3 Added re

39、quirement for construction package to include MSSI Paragraph 3.5 Added weight range requirement Paragraph 3.6 Added finished thickness range requirement (All sub-sequential paragraph numbers changed) Paragraph 3.7.1 (changed from 3.5.1) updated requirement to Rating 1 max according with revised FLTM

40、 102-02; changed Fade exposure requirement to 451.2 kJ/m2/ para 3.11.1 (FLTM BO 116-01) Paragraph 3.7.2 (changed from 3.5.2) - Modified Resistance to Flexing Bally Flex, added new FLTM for Bally Flex, new requirements. Added note at the end of paragraph. Paragraph 3.9 (Changed from 3.7) Taber abrasi

41、on samples requirement updated; Simulated seat wear and Wyzenbeek tests removed. Paragraph 3.11 (changed from 3.9) - Removed SAE J2412 exposure / evaluation criteria Paragraph 3.12 (changed from 3.10) Resistance to Heat Aging, added clarification note Paragraph 3.12.1 (changed from 3.10.1) added cla

42、rification Paragraph 3.14 (changed from 3.12) revised cleaners Paragraph 3.17.2 and 3.17.3 test method updated to ASTM D751 (ASTM D1117 withdrawn) Paragraph 3.28 modified Paragraph 3.33-Suppliers responsibility added control plan testing/batch as annual submission requirement Table1-Modified to incl

43、ude the number of specimens, requirement for test specimens submitted with the construction package and Batch testing for annual submission Added Table 2 at the end of the document Date: 2009 07 09 Section 3 added a note Section 3.7.2 added abradant material Section 3.10 - correction of paragraph EN

44、GINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 12 of 15 Table 1 Paragraphs No of specimens Test specimens required with the construction package submission Construction and DV testing PV testing New color/ new grain Batch testing for annual subm

45、ission 3.5 Weight 3 per each direction on 3 lots min. X X 3.6 Finished thickness 3 per each direction on 3 lots min. X X 3.7 Resistance to Flexing 3.7.1 Resistance to W-Flex 3 per each direction on 3 lots min. X X X X X 3.7.2 Resistance to Bally Flex 3 per each direction on 3 lots min. X X X X X 3.8

46、 Cold flexibility 3.8.1 Cold Flexibility preaged 1 X X X 3.8.2 Low Temp impact 1 X X X 3.9 Resistance Abrasion 3.9.1 Taber Abrasion 3 X X X X X 3.9.2 Wyzenbeek Abrasion 3 per each direction X X X X X 3.10 Resistance to Scuffing 3 X X X X 3.11 Resistance to Fade 1 per each condition X X X X 3.12 Resi

47、stance to Heat Aging 1 X 3.12.1 Visual Deterioration 1 X X X X 3.12.1.1 Xenon Arc 1 X X X X 3.12.2 Volatile loss 1 X X 3.13 Soiling and Cleanability 1 per each soiling agent X X X X 3.14 Resistance to Crocking and Dye Transfer 3.14.1 Resistance to Crocking 1 X X X X 3.14.2 Resistance to Dye Transfer

48、 1 X X X X X For light colors only; L value 50 3.15 Resistance to Migration Staining and Blocking 1 X X X X 3.16 Seam Fatigue Resistance 5 in each direction X X 3.17 Resistance to tear 3.17.1 Unsupported film 5 in each direction X X 3.17.2 Trapezoidal tear - supported films 5 in each direction X X E

49、NGINEERING MATERIAL SPECIFICATION WSS-M8P3-E1/E2/E3 Copyright 2014, Ford Global Technologies, LLC Page 13 of 15 Table 1 (Cont.) Paragraphs No of specimens Test specimens required with the construction package submission Construction and DV testing PV testing New color/ new grain Batch testing for annual submission 3.17.3 Foam laminated 5 in each direction X X

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1