1、 WORLDWIDE ENGINEERING STANDARDS General Specification GMW3278 Hexagon Nuts Style 1 Product Grade A Copyright 2011 General Motors Company All Rights Reserved October 2011 Originating Department: North American Engineering Standards Page 1 of 4 1 Introduction 1.1 Scope. This standard gives specificat
2、ions for hexagon nuts, Style 1 with thread diameters from M5 to M12. Basis for this standard is ISO 4032 See Figure 1. 1.2 Designation. GMW3278. 2 References Note: Only the latest approved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ISO 724 ISO 4032 IS
3、O 898-2 ISO 4759-1 ISO 965-1 ISO 6157-2 ISO 1502 ISO/TS 16949 2.2 GM Standards/Specifications. GMW3059 3 Requirements Figure 1: Hexagon Nut Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3278 Copyright 2011 Gene
4、ral Motors Company All Rights Reserved October 2011 Page 2 of 4 3.1 Dimensions. See Figure 2 and Table 1. Figure 2: Dimension Illustration Table 1: Dimensions Diameter M5 M6 M8 M10 M12 P Pitch 0.8 1 1.25 1.5 1.75 da Maximum 5.75 6.75 8.75 10.75 13 Minimum 5 6 8 10 12 dw Minimum 6.9 8.9 11.6 13.6 16.
5、6 e Minimum 8.79 11.05 14.38 16.64 20.03 m Maximum 4.7 5.2 6.8 8.4 10.8 Minimum 4.4 4.9 6.44 8.04 10.37 mw Minimum 3.5 3.9 5.2 6.4 8.3 s Maximum 8 10 13 15 18 Minimum 7.78 9.78 12.73 14.73 17.73 Property Class 8 8 8 10 10 Provided by IHSNot for ResaleNo reproduction or networking permitted without l
6、icense from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3278 Copyright 2011 General Motors Company All Rights Reserved October 2011 Page 3 of 4 3.2 Material. Steel, ISO 898-2. See Table 1 for property class for each nut diameter. 3.3 Surface Treatment. As specified on the detail drawing. 3.4 Threa
7、d. ISO 724, ISO 965-1. Thread tolerance recommended 6G before surface treatment. After surface treatment, the thread shall be gaged according to ISO 1502 with a GO-gage of tolerance H. 3.5 Tolerances. Product Grade A, ISO 4759-1. 3.6 Surface Discontinuities. ISO 6157-2. 3.7 Mechanical Properties. IS
8、O 898-2. 3.8 Acceptability. ISO/TS 166949, GM Product Part Approval Process (PPAP). 4 Rules and Regulations 4.1 Legal Regulations. All materials must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 4.2 Language. In the event of conflict between the Engl
9、ish and domestic language, the English language shall take precedence. 4.3 Inspection and Rejection. Samples of components or materials released to a GM general specification shall be tested for conformity with the requirements of this general specification and approved by the responsible Engineerin
10、g department prior to commencement of delivery of bulk supplies. A new approval must be received for any changes, e.g., properties, manufacturing process, location of manufacture, etc. If not otherwise agreed, all testing and documentation normally required for initial release must be completed. It
11、is the responsibility of the supplier to inform the customer in a timely manner, without solicitation, and to include documentation of all modifications of materials and/or processes and to apply for a new release. If not otherwise agreed, all release tests shall be repeated and documented by the su
12、pplier prior to commencement of delivery of non-conforming bulk supplies. In individual cases, a shorter test can be agreed to between the responsible Engineering department and the supplier. 4.4 Initial Source Approval. Not applicable 4.5 All materials supplied to this standard must comply with the
13、 requirements of GMW3059, Restricted and Reportable Substances for Parts. 5 Notes 5.1 Glossary. Not applicable. 5.2 Acronyms, Abbreviations, and Symbols. PPAP Product Part Approval Process 6 Coding System This standard shall be referenced in other documents, drawings, etc., as follows: GMW3278 7 Rel
14、ease and Revisions This standard was originated in May 1999. It was first approved by Fasteners Engineering in February 2000. It was first published in June 2000. Issue Publication Date Description (Organization) 1 JUN 2000 Initial publication. 2 JUN 2001 Editorial revision. (GMNA) 3 MAY 2005 Reform
15、atted 3.3. (Fasteners Group) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW3278 Copyright 2011 General Motors Company All Rights Reserved October 2011 Page 4 of 4 Issue Publication Date Description (Organization) 4 OCT 2011 Five year refresh. Removed part numbers and finish from the spec, revised M10 WAF from 16 mm to 15 mm. (Fasteners Global Council) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
