ICONTEC 966-1981 《涂料，测量其对湿气磨蚀的抗性》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST 28038-2013 Fruit and vegetable products Methods for determination of mycotoxin patulin《水果和蔬菜制品 棒状真菌霉素的测定方法》.pdf

GOST 28040-1989 Cosmonaut-s life and activity support systems complex on board of manned spacecraft Terms and definitions《在驾驶宇航器中宇航员生活机能的综合保证系统 术语和定义》.pdf

GOST 28041-1989 Crossovers section insulators frogs for tramway and trolleybus catenary suspensions General technical requirements《电车和无轨电车接触电线路的交叉点 分段绝缘子和转辙器 一般技术要求》.pdf

GOST 28043-1989 Personal computers Removable heads hard fixed disk drive interface General requirements《个人电子计算机 硬磁盘存储器移动头间的接口 一般要求》.pdf

GOST 28044-1989 Internal broaches for straight splines based at internal diameter one pass combined type Construction《内径定心直齿十键孔用交替切削装配式拉刀 结构》.pdf

GOST 28045-1989 Internal broaches for straight splines based at internal diameter dauble pass combined type Construction《内径定心直齿十键孔用两次拉削成形的交替切削组合拉刀 结构》.pdf

GOST 28046-1989 Internal broaches for straight splines based at internal diameter three pass combined type Construction《内径定心直齿十键孔用三次拉削成型的交替切削装配式组合拉刀 结构》.pdf

GOST 28047-1989 Internal broaches for straight splines based at internal diameter four pass combined type Construction《内径定心直齿十键孔用四次拉削成形的交替切削装配式组合拉刀 结构》.pdf

GOST 28048-1989 Broaches with diameter from 50 to 120 mm for slitting holes with involute profile with round tail and centring at outside diameter with modul frome 1 5 to 2 5 mm Co.pdf