1、IES LEM-7-13 IES LEM713 Addendum A Jan. 30, 2018 Page 1 of 20 Addendum A for LEM713: Lighting Controls for Energy Management If you, as a user of IES LEM713, believe you have located an error not covered by the following revisions, you should email your information to Pat McGillicuddy, pmcgillicuddy
2、ies.org, or send a letter to Pat McGillicuddy, Manager of Standards Development, IES,120 Wall St., 17thFloor, New York, NY 10005. Additions will be posted to this list online as they become available. Revisions to IES LEM713 Section 3.2 Economic Considerations In the last paragraph, after the first
3、sentence, which reads: “Additional variables impacting the economic performance of lighting control systems include energy rates, peak demand charges, installation and commissioning costs, and any available financial incentive such as utility rebates rewarding users for power or energy reductions or
4、 installations of specific lighting control devices.” Add the following sentence: “It should be noted that reducing lighting energy reduces heat load, which may provide a reduction in energy needed for cooling. Add the following text at the end of the last paragraph: “It should be noted that control
5、 features for color change (CCT and color rendering) in support of biologic applications (circadian rhythms, performance and alertness, healing, horticultural applications, animal husbandry, or unity with exterior environment) can result in increased energy consumption if not implemented properly.”
6、IES LEM-7-13 IES LEM713 Addendum A Jan. 30, 2018 Page 2 of 20 New Annex: Annex B LED OnOff Control and Dimming INTRODUCTION LED technology is capable of smooth, flickerfree dimming over a wide rangetypically down to 10% or less, and even down to 1% or less on premium commercial dimming systemswhich
7、is why LED dimming is an effective means of reducing the overall energy consumption of lighting systems. All the lighting control strategies described in Section 2 are applicable to LED technology. This annex supplements IES LEM713 to update and augment the information specific to LED dimming in Sec
8、tion 5.5 Solid State Lighting and Section 7 Control Protocols. B.1.0 LED DRIVERCONTROLLED DIMMING IMPLEMENTATION B.1.1 LED Driver Outputs LED drivers are designed to be either constant current or constant voltage output devices, and these two types of drivers are not interchangeable. It is typically
9、 the luminaire manufacturers responsibility to select the driver type and configuration to meet the electrical requirements of the LED module(s) used in the luminaire. Constant voltage drivers provide a fixed voltage to multiple LED arrays, LED modules, LED tape, or LED luminaires that are connected
10、 in parallel, e.g., cove or undercabinet lighting. Constant voltage drivers are typically electronic, but some magnetic low voltage (MLV) and electronic low voltage (ELV) transformers used for halogen strip lights in a cove or with MR16 lamps or luminaires can also be used as constant voltage driver
11、s. These drivers commonly provide 12V or 240V outputs, although other output voltages are possible. Dimming of LED lighting that uses constant voltage drivers can only be accomplished via a pulsewidth modulation (PWM) output method, described later. In addition, MLV or ELV transformers can be used w
12、ith some types of LED modules. These need to be dimmed using the appropriate dimmer type, also described later. Constant current drivers provide an unchanging current, e.g., 700 mA, to a dedicated LED module that is designed to operate at that current level. Constant current drivers are commonly use
13、d for downlights, sconces or other LED luminaires. While most constant current drivers provide one output current, some can be adjusted to support multiple output currents, which provides design flexibility to accommodate different light outputs. There are two different dimming methods for adjusting
14、 the output current for constant current drivers: PWM and constantcurrent reduction (CCR). Although most drivers use one method or the other, some dimming divers use a combination of the two methods. PWM is accomplished through current switching between 0 amps and the rated output current at a speci
15、fic modulation frequency, meaning that the LED load is either on (at rated current) or off. The ratio of ontime to offtime determines the perceived brightness of the LED source. Figure B1 shows an example of the current for an LED source dimmed to approximately 25% of full perceived brightness as a
16、result of current flowing for 25% of the each cycle. IES LEMIES LEM7Figure B1By definithuman eylikelihoodin order toelectronic(IEEE 1789health risIn CCR dimlight outpbrightnesapproximFigure B2CCR dimin applicMRI roomB.1.2 OnThe growproducts source. Dto ensureThe most manually -7-13 13 . Dimming usio
17、n, PWM dime. Frequenciof discernibleliminate stequipment, ) that specifks to viewersming, the cuut is proports of the LED. ately 25% of . Dimming uming has sevations with sts, and for aOff Control oing interest inneed to be coue to the natsuccessful swbasic form ofwith wall swiing pulse widming is a
18、ccoes lower thane flicker decrroboscopic eincluding vidies the minim. rrent flows cional to the cFigure B2 shofull light outpsing constaneral advantagrict EMI requpplications wf LEDs the use of Lmpatible witure of LEDs, itching. LED lightingtches or relaAddendumth modulatimplished at 200 Hz are peas
19、ing as freffects in fasteo systems. Ium frequencontinuously urrent flowinws an examut using CCRt current redes over PWMirements, inith high motiED lighting foh switching cthere are speonoff contry control systA Jan. 30,on (PWM) (Ifrequencies otentially obquency incremotion envirn addition, IEy at wh
20、ich dat a set valueg through thple of the cur. uction (CCR)dimming focluding videoon activity orr many geneontrols, whiccific technicaol is linevoltaems. Automa, 2018mage courtehigh enough servable in pases. Higher onments or EE has publisrivers need tofor a given le LED, a redurent for an L(Image c
21、ourtr certain appconference arotating maral illuminatih provide onl consideratige switchingtic switchingsy of Lutron,to be imperceripheral visfrequencies ainterference hed a recomoperate to ight level. Sinction in curreED source thaesy of Lutrolications. CCpplications, chinery. on applicatiooff cont
22、rol oons and prod. Switching isusing occupPage 3Inc.) eptible to theion, with there also requiwith other mended praavoid potentce the amount will reduct is reduced n, Inc.) R dimming ismedical suitens means thef the LED liguct requiremaccomplisheancy sensorsof 20 e red ctice ial nt of e the to used
23、s and LED ht ents d or IES LEM-7-13 IES LEM713 Addendum A Jan. 30, 2018 Page 4 of 20 daylight sensors can provide cost effective control to meet minimum building code requirements. The instanton and zero warmup time of LED sources provide superior functionality in warehouses, sports facilities and e
24、xterior switching applications. Luminaires that include multiple switched circuits can also utilize multilevel switching, in which portions of the luminaire can be turned off or on based on the needs of the occupants of the space. Since luminaires are turned on or off instantly, switching control is
25、 primarily utilized in applications where adjustability of the overall lighting level is needed but the aesthetics associated with dimming are not required. B.1.3 Dimming Controls for LED Lighting In general, dimming controls for LED lighting can be implemented via either of two methods: Direct dimm
26、ing of the line voltage feeding the LED lamp or luminaire Providing a separate control input to the driver that is typically a lowvoltage analog or digital signal (referred to as directly controlled because the signal acts directly as the method of level control, as opposed to control of line voltag
27、e or current) Because the control input type is independent of the driver output type (constant current or constant voltage), ensuring the compatibility of a control with a particular LED lamp or luminaire begins with verifying that both use the same control method, whether its a simple standalone w
28、all box dimmer or a more complex lighting control system. Dimming of the line voltage is implemented via either of two methods. These methods are commonly referred to as forward phase control (FPC), also known as leading edge (LE), and reverse phase control (RPC), also known as trailing edge (TE). B
29、.1.3.1 Forward Phase Control Dimming Forward phase control dimming is also sometimes referred to as triac dimming because of the bidirectional triode thyristors (commonly called triacs), components that can only be used in FPC circuit designs. Historically used for incandescent and MLV transformers,
30、 this is the most common method of line voltage dimming control. The U.S. National Electrical Manufacturers Association (NEMA) estimates that there are over 150 million FPC dimmers installed, and many of these are likely to be used for control of LED lamps as incandescent lamps are replaced. Unfortu
31、nately, these dimmers were never designed for LED loads and typically do not have safety certification for this application. Performance may be inadequate in many cases, with LED flicker, dropout, popon, or failure to dim at low levels commonly occurring. Figure B3 shows and example of an FPC dimmin
32、g diagram. IES LEMIES LEM7FiThwlainFPnmofFidasofFiFiatdNlamh-7-13 13 gure B3. Forere are a nuith LED lightimps they repimproper orC dimmer mecessarily opay draw onlyAC power thgure B4). Thiesign limits, aexcessive acup to a 100gure B4. Repnally, becauslow light levriver circuitryewer FPC dimmps, inc
33、ludinany lamp maelp ensure acward phase mber of caveng. LED lamplace and mayinadequate ust also be cerate satisfac15 W continat causes thes transient cund may causoustic noise.watt incandeetitive peak e LEDs are veels will be de. Even minutmers are deg the ability nufactures pceptable dimAddendumcon
34、trol (FPC)ats associatewattages arnot meet thoperation of onsidered. Fotorily when cuously, it wilsame demarrent puts sie premature LED loads asscent lamp.current comry sensitive tpendent on te fluctuationsigned to redto drive smarovide compming performA Jan. 30,dimming. (Imd with the use generally
35、loe minimum lthe LED lampr example, aonnected to l exhibit a repnd on the dimgnificant streproduct failulow as 20 Wparison. (Imao small chanhe power qus in line voltauce or eliminllwattage loaatibility lists fance. , 2018mage courtese standard fwer than theload requirem. In addition600watt inc40 15w
36、att Letitive peak mer as a 60ss on the dimre or impropcan result inge courtesy ges in currenality of the Age may resulate the probds. Some dior specific LEsy of Lutron, orward phasewattage of ent of the d, the maximuandescent dED lamps. Wcurrent durinwatt incandmer, exceeder system pethe same eleof
37、Lutron, Int, the stabilitC source andt in visible flilems with commer manufD lamps andPage 5Inc.) control dimthe incandesimmer, resulm rating of timmer will nohile the LED lg every halfescent load (s the dimmerformance, sctrical demac.) y of an LED lathe design ocker in the lantrolling LEDacturers a
38、ndluminaires tof 20 mers cent ting he t amp cycle see rs uch nds mp f the mp. o IES LEMIES LEM7BRtorecothlainodFiBStNdnfoa AteBThthhthbpd-7-13 13 .1.3.2 Reverseverse phasecontrol elecquire reversntrol methoe installed nmp and lumiternal electrolder buildingsimming diagrgure B5. Rev.1.3.3 Compaandard
39、s are EMA SSL7A1immers and aot ensure thallowup stanlevel of dimmdditionally, ssting and pro.1.3.4 LED Diis control tyreewire lineot wire and aan 2wire coeen used for opon. The surivers designee Phase Contcontrol is sotronic low voe phase contrds are due toumbers of incnaire manufanics. Not ev, whic
40、h limitam. erse phase ctibility being develostandard speddresses comt dimming pedard, NEMA ing performome LED lamvide results mming Usingpe is a form ovoltage conneutral wirentrol, with reover thirty yebstantial exid with a 3wAddendumrol (RPC) Dimmetimes refeltage (ELV) trol.) RPC dimthe similaritan
41、descent dcturers. RPCery electricals the applicabontrol (RPC)ped that addcifies basic ipatibility anrformance wSSL7B, is undance that wilp manufactuon their respExisting 3wf forward phnections cons. Providing aduced suscears to dim flsting base of ire control inA Jan. 30,ming rred to as ELansformers
42、. ming is ofteny to transformimmers, RPCdimmers typswitch box hility of RPC.dimming. (Imress compatinteroperabilid reliability. ill meet the er developml be acceptabrers and dimmective websitire Fluorescease control tist of a dimmthird wire foptibility to eleuorescent ba3wire dimmput with min, 2018V
43、 dimming b(Note, howevn more effectier loads. Wis often the cically requireas a neutral wFigure B5 shage courtesbility betweety between LHowever, SSLneeds and exent, with thele to consummer manufaces. nt Controlsypically useded hot (forwr control alloctrical noiseallasts to 1% wing installatioimal o
44、r no mecause it is trver, that not ve with LED dhile they do ontrol type sa neutral wire availablehows an examy of Lutron, n drivers andED lamps and7A compliapectations ointent of prers. turers perford for fluoresceard phase) wws for more. Threewire ithout flickens can be usodification. Page 6aditio
45、nally uall ELV dimmrivers than onot have neaupported byire connectio, particularlyple of an RPCInc.) LED loads. Tphasecontnce alone dof customers. oviding criterm inhouse nt dimming. ire, a switchprecise dimmcontrols haver, dropout, oed with LED of 20 sed ers ther rly LED n for in he rol es A ia for
46、 The ed ing r IES LEM-7-13 IES LEM713 Addendum A Jan. 30, 2018 Page 7 of 20 B.1.4 Low Voltage Analog and Digital Control of LED Lighting There are several common low voltage protocols which have historically been used to control older types of lighting and are now being used to control LED lighting.
47、 Typical low voltage analog protocols include: 010 V (as defined by standard IEC 60929 Annex E2or ANSI C82.113) PWM (as defined by standard IEC 60929 Annex E) Typical low voltage digital protocols include: DALI (as defined by standard IEC 628364) DMX512 (as defined by standard ANSI E1.115) In additi
48、on to the protocols mentioned above, other protocols exist, some of which are either a variation of one of those mentioned or may be significantly different. Luminaire manufacturers specify the drivers that can be used with their products, and most offer several driver options in order to accommodat
49、e different control systems. Driver manufacturers, in turn, specify the control protocol required for proper operation. It is up to the user to match the control type with driver manufacturer recommendations. B.1.4.1 Analog 010 V Control Protocol The control wiring between dimmer and driver for this control type consists of two wires for low voltage DC dimming control (Class 1 or 2 wiring, depending on the luminaire rating). Line voltage to the LED driver is switched to turn the driver on an
