1、This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar, Inc. AUGUST 2009 Page 1 of 4 NAVISTAR, INC. CEMS (CORPORATE ENGINEERING MATERIAL SPECIFICA
2、TION) NUMBER: CEMS G-5, Part IV General TITLE: Part IV Paints Casting Sealers, General Requirements CURRENT ISSUE DATE: August 2009 WRITTEN/REVIEWED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: February 2002 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CU
3、RRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability
4、 of regulatory limits prior to use. Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; added CEMS B-50 requirement; editorial changes. 1.0 SCOPE The intent of this specification is to establish acceptable durability and quality levels
5、for the finish on Navistar products and to define requirements and physical properties of the various materials used in the painting operation. 1.1 Restricted Chemical Substances Effective January 1, 2007, all product supplied to the requirements of this specification must comply with the requiremen
6、ts of the CEMS B-50 specification. 2.0 INTRODUCTION This specification is divided into eight parts as follows: Part I, Section A - Product Finishing Requirements Part V - Primers Part I, Section B - Paint Material Requirements Part VI - Paints for Repair phone: 1-800-854-7179; website: . 8.1.1 Colo
7、r Chips Requests for color chips should be addressed to: Non-Metals Laboratory, Truck Development and Technology Center, P.O. Box 1109, Ft. Wayne, IN 46801-1109 8.2 ASTM Test Methods ASTM test methods are available from ASTM, 1916 Race Street, Philadelphia, PA 19103 8.3 Federal Test Methods Federal
8、test Methods are available from the Business Service Center, General Services Administration, Washington, D.C. 20407 For documents referenced in Section 6.0 Property Requirements See Section 8.0 Test Methods Copyright Navistar International Corporation Provided by IHS under license with INTERNNot fo
9、r ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: CEMS G-5, Part IV General TITLE: Part IV Paints Casting Sealers, General Requirements CURRENT ISSUE DATE: August 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without perm
10、ission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 Navistar, Inc. AUGUST 2009 Page 3 of 4 9.0 SOURCE APPROVAL AND QUALITY CONTROL 9.1 Supplier Requirements All suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requireme
11、nts. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration cer
12、tificates to their Corporate Buyer upon request. 9.2 Approval Parts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples that were approved by the purchaser. No changes in formulation or processing practices are permitted withou
13、t approval. In the event that changes in material, properties, processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering (TDTC) and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformanc
14、e to all requirements of this specification, test samples, and new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 9.3 Process Control The supplier shall either perform and report results of tests
15、on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality
16、 control manager of the using NAVISTAR plant may determine testing and reporting requirements on specific products. 10.0 DESIGNATION ON DRAWINGS AND PURCHASE ORDERS 10.1 Engineering Drawings Engineering generally specifies only the Class of Finish on its drawings. The finish classification describes
17、 the durability, corrosion resistance, and appearance requirements of the part or assembly. It is the responsibility of the supplier or of Manufacturing to determine the need for casting sealers in order to satisfy the specified finish requirements. 10.2 Purchase Orders Purchase orders should includ
18、e the grade of the casting sealer and reference this specification: if necessary the color; by the Navistar paint color number, may be included. When necessary the desired viscosity range should also be included on the purchase order. Example: 0001-43W Black Casting Sealer, per CEMS G-5, Pt. IV Visc
19、osity 45-60 seconds 11.0 PACKING AND SHIPPING Packing, shipping and identification shall be in accordance with Manufacturing Standard MS-D-13. Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license f
20、rom IHS-,-,-NUMBER: CEMS G-5, Part IV General TITLE: Part IV Paints Casting Sealers, General Requirements CURRENT ISSUE DATE: August 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required
21、 to assume all patent liability. 2009 Navistar, Inc. AUGUST 2009 Page 4 of 4 12.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may purchase controlled copies of this specification by contacting: Materials Engineering and Tec
22、hnology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringN IHS Global Inc. 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/ Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
