1、INTERNATIONAL TRUCK AND ENGINE CORPORATION Engineering Standard Parts NUMBER: ESP-M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 WRITTEN/REVIEWED BY: Corporate Technical Standards APPROVED BY: Corporate Technical StandardsSUPERSEDES ISSUE OF: April 2002PRINTE
2、D COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION Change Notice: Revised C dimension (End to Center) on part number 444048 from 1.69” to 2.00”. AUTOMOTIVE PIPE NIPPLES (Noun Code - 5760) PREFERRED PARTS A C G D E PART NUMBERS Dryseal Taper Hexagon Shoulder Drill Brass Thread Width Leng
3、th Diameter Length Plain 1/16-27 .312 .38 .14 .94 1/8 -27 .438 .38 .22 .97 443976 1/4 -18 .562 .56 .31 1.38 443978 3/8 -18 .688 .56 .44 1.41 443980 1/2 -14 .875 .75 .56 1.81 443982 A A1C G G1D E K L PART NUMBERS Dryseal Taper Hexagon Shoulder Drill Counterbore Brass Thread Width Length Diameter Leng
4、th Dia Length Plain 1/8-27 1/16-27 .438 .38 .38 .14 .97 .19 .47 1/4-18 1/8 27 .562 .56 .38 .22 1.19 .28 .69 443986 3/8-18 1/8 27 .688 .56 .38 .22 1.22 .41 .69 443988 3/8-18 1/4 18 .688 .56 .56 .31 1.41 .41 .69 443990 1/2-14 3/8 18 .875 .75 .56 .44 1.62 .53 .91 443992 CHAMFERFor General Specification
5、s, See ESP-M-1.101-GS This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY
6、 2007 Page 1 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: ESP-M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 For General S
7、pecifications, See ESP-M-1.101-GS This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from A B C N L PART NUMBERS Dryseal Taper Hexagon Shoulder *Hole Diameter Brass Thread Width Length Min Length Plain 1/8-27 1/16-27 .4
8、38 .38 .139 .56 1/4-18 1/8 -27 .562 .56 .217 .75 444024 3/8-18 1/8 -27 .688 .56 .217 .75 444026 3/8-18 1/4 -18 .750 .56 .309 .75 444028 1/2-14 1/8 -27 .875 .75 .217 1.00 444030 1/2-14 1/4 -18 .875 .75 .309 1.00 444032 1/2-14 3/8 -18 .875 .75 .435 1.00 444034 3/4-14 1/2 -14 1.125 .75 .559 1.00 24466R
9、1 *At manufacturers option, hole may conform to tap drill diameter or may be reduced beyond tap drill depth but in no case will it be smaller than L diameter specified. AUTOMOTIVE PIPE ADAPTERS (Noun Code - 0030) Dimension in inches: A C J E D F PART NUMBERS Dryseal Taper Hexagon Tap Drill Shoulder
10、Drill Brass Thread Width Depth Length Diameter Length Plain 1/16-27 .438 .38 .38 .14 .84 443996 1/8 -27 .562 .38 .38 .22 .88 443998 1/4 -18 .750 .56 .56 .31 1.25 444000 3/8 -18 .875 .56 .56 .44 1.25 444002 1/2 -14 1.062 .75 .75 .56 1.66 444004 3/4 -14 1.375 .75 .75 .75 1.69 444006 1-11-1/2 1.625 .94
11、 .94 .94 2.06 Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY 2007 Page 2 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networki
12、ng permitted without license from IHS-,-,-NUMBER: ESP-M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 For General Specifications, See ESP-M-1.101-GS This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduce
13、d without permission from AUTOMOTIVE PIPE REDUCER ADAPTERS (Noun Code - 0030) A A1C J E D F PART NUMBERS Dryseal Taper Hexagon Tap Drill Shoulder Drill Brass Thread Width Depth Length Diameter Length Plain Max 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11 1/2 1/16-27 1/8 -27 1/4 -18 3/8 -18 1/2 -14 3/4 -1
14、4 .562 .750 .875 1.062 1.375 1.625 .38 .56 .56 .75 .75 .94 .38 .38 .56 .56 .75 .75 .14 .22 .31 .44 .56 .75 .84 1.06 1.25 1.47 1.69 1.88 444010 444012 444014 444016 444018 444020 AUTOMOTIVE PIPE REDUCER COUPLINGS (Noun Code - 2220) Dimensions in inches: A B G H J K PART NUMBERS Body Tap Brass Dryseal
15、 Taper Hexagon Shoulder Diameter Drill Depth Plain Thread Width Length Min Min Length 1/8-27 to 1/16-27 .562 .31 .50 .38 .78 1/4-18 to 1/8 -27 .750 .31 .56 .56 .97 444104 3/8-18 to 1/8 -27 .875 .25 .56 .56 .94 444106 3/8-18 to 1/4 -18 .875 .47 .75 .56 1.16 444108 1/2-14 to 1/8 -27 1.062 .25 .56 .75
16、1.19 444110 1/2-14 to 1/4 -18 1.062 .34 .75 .75 1.28 444112 1/2-14 to 3/8 -18 1.062 .44 .88 .75 1.38 444114 Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY 2007 Page 3 of 6 Copyright Navistar International
17、Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: ESP-M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 For General Specifications, See ESP-M-1.101-GS This document is
18、restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from AUTOMOTIVE PIPE COUPLINGS (Noun Code - 2220) A F G C D PART NUMBERS Dryseal Taper Hexagon Shoulder Body Brass Thread Width Length DiameterPlain Min Length 1/16-27 .438 .28 .44 .75
19、1/8 -27 .562 .27 .56 .75 444094 1/4 -18 .750 .44 .57 1.12 444096 3/8 -18 .875 .42 .88 1.12 444098 1/2 -14 1.062 .59 1.06 1.50 444100 AUTOMOTIVE 90 DEGREE PIPE ELBOWS (Noun Code - 2940) EXTRUDED TYPE Dimension in inches: A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 B C Body
20、 Size (Square) End to Center .03 7/16 .50 9/16 .55 11/16 .78 13/16 .84 1 1.09 1-1/4 1.16 1-1/2 1.52 Material & Finish PART NUMBERS Brass Plain 9409923 444068 444070 444072 444074 AUTOMOTIVE 90 DEGREE PIPE STREET ELBOWS (Noun Code 2940) A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1
21、11-1/2 B Body Size (Square) 7/16 9/16 11/16 13/16 1 1-1/4 1-1/2 C End to Center .03 .59 .66 .91 .97 1.25 1.38 2.00 E End to Center .03 .45 .48 .72 .78 1.03 1.12 1.41 G Drill Diameter .14 .22 .31 .44 .56 .75 .97 Material & Finish PART NUMBERS Brass Plain 444036 9409931 444040 444042 444044 444046 44
22、4048 Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY 2007 Page 4 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permit
23、ted without license from IHS-,-,-NUMBER: ESP-M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 For General Specifications, See ESP-M-1.101-GS This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without
24、 permission from AUTOMOTIVE 45 DEGREE PIPE STREET ELBOWS (Noun Code 2940) A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 D E Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY 2007 Pag
25、e 5 of 6 AUTOMOTIVE 45 DEGREE PIPE ELBOWS (Noun Code - 2940) AUTOMOTIVE PIPE TEES (Noun Code - 9020) EXTRUDED TYPE Dimensions in inches: F S Body Size (Square) End to Center .03 End to Center .03 Drill Diameter 7/16 .47 .38 .14 9/16 .50 .38 .22 11/16 .72 .56 .31 13/16 .78 .56 .44 1 1.00 .75 .56 1-1/
26、4 1.06 .75 .75 1-1/2 1.34 .94 .97 Material & Finish PART NUMBERS Brass Plain 9409927 444054 444056 444058 444060 444062 A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2 -14 BD Body Size (Square) 7/16 .44 9/16 .45 11/16 .66 13/16 .69 1 End to Center .03 .91 Material & Finish PART NUMBERS Brass Pl
27、ain 9409919 444082 444084 444086 Internal, Internal, Internal A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 D F Body Size (Square) 7/16 .50 9/16 .55 11/16 .78 13/16 .84 1 1.09 1-1/4 1.16 1-1/2 End to Center .03 1.52 Material & Finish PART NUMBERS Brass Plain 9409935 444120
28、444122 444124 444126 444128 Internal, Internal, External A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 E G F D Body Size (Square) End to Center .03 End to Center .03 Drill Diameter 7/16 .50 .59 .14 9/16 .55 .66 .22 11/16 .78 .91 .31 13/16 .84 .97 .44 1 1.09 1.25 .56 1-1/4 1
29、16 1.38 .75 1-1/2 1.52 1.69 .97 Material & Finish PART NUMBERS Brass Plain 9409939 444134 444136 444138 444140 444142 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: ESP-
30、M-1.103-PP TITLE: Automotive Pipe Fittings Preferred Parts CURRENT ISSUE DATE: May 2007 For General Specifications, See ESP-M-1.101-GS This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from AUTOMOTIVE PIPE TEES (Noun C
31、ode - 9020) EXTRUDED TYPE Internal, External, Internal A Dryseal Taper Thd 1/16-27 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-11-1/2 D Body Size (Square) 7/16 9/16 11/16 13/16 1 1-1/4 1-1/2 F End to Center .03 .50 .55 .78 .84 1.09 1.16 1.52 G End to Center .03 .59 .66 .91 .97 1.25 1.38 1.69 E Drill Diamet
32、er .14 .22 .31 .44 .56 .75 .97 K Tap Drill Length .66 .75 1.03 1.17 1.48 1.66 2.12 Material & Finish PART NUMBERS Brass Plain 9409943 444148 444150 444152 444154 444156 Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. MAY 2007 Page 6 of 6 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
