INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf

上传人:tireattitude366 文档编号:786135 上传时间:2019-01-29 格式:PDF 页数:7 大小:70.26KB
下载 相关 举报
INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf_第1页
第1页 / 共7页
INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf_第2页
第2页 / 共7页
INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf_第3页
第3页 / 共7页
INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf_第4页
第4页 / 共7页
INTERN TMS 7006-2008 Non-Metallic Tubing (SAE J844)《非金属管(SAE J844)》.pdf_第5页
第5页 / 共7页
点击查看更多>>
资源描述

1、NAVISTAR, INC. TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-7006 TITLE: Non-Metallic Tubing (SAE J844) CURRENT REV No.: 0806 DATE: June 2008WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering SUPERSEDES: Rev L - April 2003 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FO

2、R CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicabi

3、lity of regulatory limits prior to use. Change Notice: Replaced “International Truck and Corporation” with “Navistar, Inc.” per corporate directive; updated Tables 1 and 2; added restricted chemical substances requirements as Section 2.3; editorial changes. Reference: File 20-3 Keywords: Tubing, nyl

4、on tubing, non-metallic tubing, air tube. 1.0 APPLICATION This specification outlines the minimum requirements for non-metallic tubing that may be used in certain portions of the air brake systems (see Restrictions in SAE J844 and J1394), in the secondary air system (such as air horns, air shift lin

5、es, air wipers, and air seats), and in fuel lines. This tubing is restricted to use in a temperature range of -40 to 93C (-40 to 200F) and to a maximum working pressure of 1034 kPa (150 psi). Tubing used in the fuel system is also controlled by TMS-7134. 2.0 SCOPE This specification covers the gener

6、al requirements, property and performance requirements, quality control and KCC requirements for two types of non-metallic tubing. 2.1 Type A: This is a non-reinforced tubing for use in secondary air system applications outside of the primary braking system. 2.2 Type B: This is a reinforced tubing t

7、hat may be used in the primary braking system as well as other air system applications and in the fuel system. NOTE 1: These tubing types should not be used for compressor discharge lines or in other applications where temperatures exceed 93C (200F), or pressures exceed 1034 kPa (150 psi). NOTE 2: S

8、ome existing engineering drawings may refer to TMS-7006, Type C in these applications tube provided will meet the requirements of TMS-7134, Type A. NOTE 3: Some existing engineering drawings may refer to TMS-7006, Type D in these applications tube provided will meet the requirements of TMS-7134, Typ

9、e B. 2.3 Restricted Chemical SubstancesEffective January 1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall app

10、ly. The following specifications and standards are referenced in this specification: This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2008 by Navistar, In

11、c. JUNE 2008 Page 1 of 7 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7006 TITLE: REVISION: Non-Metallic Tubing (SAE J844)0806 This document is restricted and may n

12、ot be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Quality System Standard ISO 9001 or TS-16949 NAVISTAR TMS-7106 SAE J844 NAVISTAR Engineering Design Std. A-16 NAVISTAR TMS-7134 SAE J1131 NAVISTAR Manufacturing Std. MS-D-13 ASTM D 471 SAE J1394 CF

13、R Title 29, Part 1910 ASTM D 638 FMVSS-106 NAVISTAR CEMS B-50 4.0 GENERAL REQUIREMENTS The tubing for these applications shall meet the requirements of SAE J844 (SAE J1394 for Metric Equivalents) Air Brake Tubing and SAE J1131 (Performance Requirements) and any additional requirements outlined in th

14、is specification. 4.1 Material The tubing shall be constructed as indicated for the type: 4.1.1 Type A Construction: A single wall extrusion, 100% virgin polyamide (nylon Type 11 or 12) 4.1.2 Type B Construction: Seamless, polyamide (nylon Type 11 or 12) or polyamide composite core tube wrapped with

15、 a polyester fiber reinforcement, and then covered with a smooth outer sheath of polyamide (nylon 11, or 12) or polyamide composite with the outermost layer being polyamide (nylon 11 or nylon 12) bonded to the core tube. 4.2 Appearance The tubing shall compare to and be equivalent in surface finish

16、and color to the original samples approved by NAVISTAR Truck Development and Technology Center. Tubing supplied to this specification shall be smooth and uniform, free from any visible defects, foreign matter, kinks, seams or any other condition that would impair the performance. 4.3 Color Tubing co

17、lor formulation shall be consistent in hue and of uniform saturation. Type A tubing shall be solid black in color, unless otherwise specified. Type B tubing shall have a black cover, unless otherwise specified, and the core tube shall be of a contrasting color. 4.4 Tolerances Tubing provided will me

18、et the OD and wall thickness tolerances for the type and size tube as indicated: Tube Tube O.D. and Wall Outside Diameter Wall Thickness Tolerance Tubing Type mm in mm in mm inA 3.18 0.125 0.58 0.023 0.08 0.003 A 3.97 0.156 0.58 0.023 0.08 0.003 A 6.35 0.250 1.02 0.040 0.08 0.003A 7.93 0.312 1.02 0.

19、040 0.10 0.004 B 9.53 0.375 1.57 0.062 0.10 0.004B 12.70 0.500 1.57 0.062 0.10* 0.004* B 15.88 0.625 2.34 0.092 0.13 0.005 B 19.05 0.750 2.34 0.092 0.13 0.005*For wall only; O.D. tolerance = 0.13 mm or 0.005 in Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 P

20、age 2 of 7 Copyright Navistar International Corporation Provided by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7006 TITLE: REVISION: Non-Metallic Tubing (SAE J844)0806 This document is restricted and may not be sent out

21、side Navistar, Inc. or reproduced without permission from Corporate Technical Standards. 4.5 Property And Performance Requirements - Tubing Only Tubing furnished to this specification shall meet requirements of SAE J844 (SAE J1394 for Metric Equivalents), Air Brake Tubing, SAE J1131 (Performance Req

22、uirements), all applicable requirements of FMVSS-106 and, in addition, the following requirements. 4.5.1 Fuel Resistance 4.5.1.1 Method: Fill a test sample 45 cm (18 in) long with ASTM Fuel “B“ (Reference ASTM D 471) and age 100 hours at 24 3C (75 5F). Determine volume change. 4.5.1.2 Required: 2.5%

23、 maximum volume change 4.5.2 Tensile and Elongation 4.5.2.1 Method: ASTM D 638 (Perform test on production lots of tubing; determine elongation and tensile strength from original tube area. Rate of pull shall be 25 mm (1 in) per minute.) 4.5.2.2 Required Type A: 24 MPa (3500 psi) min tensile strengt

24、h - 200% min ultimate elongation 4.5.2.3 Required Type B: 24 MPa (3500 psi) min tensile strength - 150% min ultimate elongation 4.6 Property And Performance Requirements - Tubing and Fitting AssembliesAssemblies shall meet the requirements of SAE J1131 except as follows: 4.6.1 Tension Test When test

25、ed in accordance with SAE J1131, assemblies shall withstand the load shown below without causing separation from the fitting. Tubing OD Tensile Load3.2 mm (1/8“) 67 N (15 lbs) 4.0 mm (5/32“) 178 N (40 lbs) 6.4 mm (1/4“) 222 N (50 lbs) 7.9 mm (5/16“) 334 N (75 lbs) 9.5 mm (3/8“) 667 N (150 lbs) 12.7

26、mm (1/2“) 890 N (200 lbs) 15.9 mm (5/8“) 1446 N (325 lbs) 19.1 mm (3/4“) 1557 N (350 lbs) 5.0 SUPPLIER QUALITY CONTROL REQUIREMENTS The supplier shall perform the following control tests of material and production parts on a continuing basis according to the minimum sample size and test frequencies

27、stipulated. The supplier shall maintain a complete record of test results. Certification of compliance shall be furnished for each shipment. All tests shall be performed in conformance to the requirements in the Properties and Performance section of this specification, as per SAE J844, SAE J1131, or

28、 SAE J1394. Test FrequencyLeakage Each continuous production length Adhesion Each continuous production length Burst (Room Temperature) One sample per each production lot* Tensile and Elongation One sample per each production lot* Cold Temperature Impact One sample per each production lot* Outside D

29、iameter* Monitor continuously and record * A lot shall consist of one size and color tubing made during a single production shift. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 3 of 7 Copyright Navistar International Corporation Provided by IHS under li

30、cense with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7006 TITLE: REVISION: Non-Metallic Tubing (SAE J844)0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical St

31、andards. * Outside diameter of Type A tubing and outside diameter of the core tubing and all sheathed oducts of Type B tubing. prNOTE: All quality control tests described in this specification, that require tube-to-fitting connections, shall be conducted using the currently approved production tube

32、fittings. 5.1 Qualification Material and process submitted for approval to this specification shall include the following: 5.1.1 Report: A detailed and signed report documenting testing to this specification prepared as per TMS-9543. The report will include actual test data and not merely test summa

33、ries. 5.1.2 Failure Modes: Test samples or photographs showing failure modes for each destructive test. 5.1.3 Test Procedure: The procedure used for preparing, curing, and assembling sample for test, will be submitted for review. 5.1.4 Analysis: A detailed analysis of the test results including assu

34、mptions made, discussion of unexpected results and a full explanation of any non-compliant results. 5.2 Key Control CharacteristicsUnless specific exception is noted on the engineering drawing, blueprint, and/or purchase order, the following features/characteristics* are identified as features for w

35、hich management by statistical process control* is mandatory for all hoses and/or hose assemblies (all hose Types) supplied to the requirements of this specification: KCCOutside Diameter * Other Characteristics for inclusion in the control plan may be specified on the engineering drawing and/or purc

36、hase order. * See Engineering Design Standard A-16 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.1 Supplier RequirementsAll suppliers to NAVISTAR are required to be registered to ISO 9001 Quality System Requirements. NAVISTAR will also accept TS-16949 registration as long as the supplier can also fulfil

37、l all AIAG PPAP (Production Part Approval Process) documentation and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their Corporate Buyer upon request. 6.2 ApprovalParts supplied against contract

38、s or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties, processing practices, constru

39、ction, color, or labeling of the product are required, the supplier shall notify NAVISTAR Truck Development and Technology Center and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and new or am

40、ended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. Suppliers are required to assume all patent liability. 2008 by Navistar, Inc. JUNE 2008 Page 4 of 7 Copyright Navistar International Corporation Provided

41、by IHS under license with INTERNNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NUMBER: TMS-7006 TITLE: REVISION: Non-Metallic Tubing (SAE J844)0806 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corpora

42、te Technical Standards. 6.3 Process ControlThe supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949 guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capa

43、ble of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determine testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION 7.1 Identification The tubing and

44、 fittings furnished to this specification shall comply with the identification requirements of Federal Motor Vehicle Safety Standard 106 and SAE J844. Any size not regulated by FMVSS shall be identified in accordance with SAE J844 and this specification. In case of conflicting identification require

45、ments, DOT, FMVSS, and/or SAE requirements shall prevail in the order cited. 7.2 Tube LabelingEach tube shall be labeled or marked on the outer cover along the entire length of tube at intervals of 330-380 mm (13-15 inches) with a maximum spacing of 150 mm (6 inches) between repeats. The markings sh

46、all be in a color contrasting to that of the tube cover color, in clearly legible block capital letters not less than 3 mm (1/8 inch) high, except for sizes under 6.4 mm (1/4 inch) O.D. which shall be the maximum size possible, with the following minimum information: 7.2.1 Vendor Code: A four-or-fiv

47、e-digit code assigned by NAVISTAR to each vendor. Contact Corporate Technical Standards, Truck Development and Technology Center, for assignment of codes. 7.2.2 Hose Type: Identification by hose type, as required 7.2.3 Size: Nominal size, i.e., diameter in fractions of an inch or “dash” sizes, as re

48、quired. 7.2,4 NAVISTAR Part Number7.2.5 Date Code: The six-digit date code, with first two digits (01-12) representing the month, second two digits (01-31) representing the day, and last two digits (e.g. 01) representing the year, is the preferred method for date codes. Other methods of date code may be used by agreement between the purchaser and supplier 7.2.6 Certification: DOT certification symbol when applica

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > 其他

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1