JUS N C6 134-1993 Coaxial cables for cable distribution systems and common antena systems RF 75-5-6 F V RF 75-5-6 S V RF75-5-6 F P RF 75-5-6 S P《用于布线系统和普通天线系统RF 75-5-6 F V,RF 75-5-.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

CNS 15076-1-2007 Modular units for machine tools - Workholding pallets - Part 1 Workholding pallets up to 800 mm nominal size《工具机之模块单元－工件固定托板－第1部：标称尺度800mm以下之工件固定托板》.pdf

CNS 15076-2-2007 Modular units for machine tools - Workholding pallets - Part 2 Workholding pallets of nominal size greater than 800 mm《工具机之模块单元－工件固定托板－第2部：标称尺度800mm以上之工件固定托板》.pdf

CNS 15077-4-2007 Test conditions for machining centers - Part 4 Accuracy and repeatability of positioning of linear and rotary axes《切削中心机之检验条件－第4部：线性轴与旋转轴之定位精度与重现性》.pdf

CNS 15077-5-2007 Test conditions for machining centers - Part 5 Accuracy and repeatability of positioning of work-holding pallets《切削中心机之检验条件－第5部：工件夹持托板之定位精度与重现性》.pdf

CNS 15077-6-2007 Test conditions for machining centers - Part 6 Accuracy of feeds speeds and interpolations《切削中心机之检验条件－第6部：进给、速率与插值之精度》.pdf

CNS 15077-7-2007 Test conditions for machining centers - Part 7 Accuracy of finished test piece《切削中心机之检验条件－第7部：精加工之试件精度》.pdf

CNS 15077-8-2007 Test conditions for machining centers - Part 8 Evaluation of contouring performance in the three coordinate planes《切削中心机之检验条件－第8部：在三个坐标平面内之轮廓性能评估》.pdf

CNS 15077-9-2008 Test conditions for machining centres - Part 9 Evaluation of the operating time of tool change and pallet change《切削中心机之检验条件－第9部：刀具与托板更换之操作时间评估》.pdf

CNS 15078-2007 Method of test for determination of the oxidation stability of middle distillate fuels《中质蒸馏燃油氧化稳定性测定法》.pdf