JUS N M2 150-1990 Safety requirements Electrical shtmers and ha ir clippers Particular technical condltions and tests《安全要求 电动剃须刀及发剪 特殊技术条件及测试》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST 20531-1975 Combined needle taper roller bearings Specifications《组合式向心推力滚针轴承 基本尺寸》.pdf

GOST 20532-1983 Television radiotransmitters of I-V bands Basic parameters technical requirements and measuring methods《I－V波段电视无线电发射机 基本参数，技术要求和测量方法》.pdf

GOST 20533-1975 Pintle end mills with solid carbide tips Construction and dimensions《镶硬合金圆柱柄立铣刀 结构及尺寸》.pdf

GOST 20534-1975 Taper shank end mills with solid carbide tips Construction and dimensions《镶硬质合金锥柄立铣刀 结构及尺寸》.pdf

GOST 20535-1975 Thread shank end mills with solid carbide tips Construction and dimensions《镶硬质合金螺纹柄立铣刀 结构及尺寸》.pdf

GOST 20537-1975 Taper shank end mills of 12 5-50 mm diameter with spiral carbide blades Construction and dimensions《镶螺旋硬质合金刀片锥柄直径12 5～50mm立铣刀 结构及尺寸》.pdf

GOST 20538-1975 Elongated taper shank end mills of 20-50 mm diameter with spiral carbide blades Construction and dimensions《镶螺旋硬质合金刀片锥柄直径20～50mm加长立铣刀 结构及尺寸》.pdf

GOST 20539-1975 End mills with solid carbide tips and with spiral carbide blades Specifications《镶硬质合金头及螺旋刀片立铣刀 技术要求》.pdf

GOST 20544-1975 Ground feldsparic and quartzfeldsparic materials Method for determination of mica content《长石及磨碎石英--长石材料 云母含量测定法》.pdf