KS R ISO 6697-2003 Cycles－Hubs and freewheels－Assembly dimensions 《自行车 轮毂和游滑轮的组装尺寸》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D716-B1-2016 POLYETHERIMIDE (PEI) MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D719-A2-2006 POLYAMIDE (PA) 66 38% GLASS FIBER MINERAL REINFORCED MOLDING COMPOUND 25% POST CONSUMER MINERAL FILLED NYLON TO BE USED WITH FORD WSS-M99P1111-A (Shown on.pdf

FORD WSS-M4D719-A3-2007 POLYAMIDE (PA) 66 40% MINERAL REINFORCED MOLDING COMPOUND HEAT STABILIZED 25% POST CONSUMER CONTENT - TO BE USED WITH FORD WSS-M99P1111-A 《25%消费后回收、受热稳定的4.pdf

FORD WSS-M4D725-B1-2012 POLYBUTYLENE TEREPHTHALATE (PBT) 30% GLASS FIBER REINFORCED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D726-A3-2010 POLYETHYLENE TEREPHTHALATE (PET) 30% GLASS FIBER REINFORCED POST CONSUMER RECYCLATE MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%玻璃纤维增强的聚对苯二甲酸.pdf

FORD WSS-M4D729-A3-2006 POLYPROPYLENE (PP) HOMOPOLYMER 20% TALC FILLED INJECTION MOLDING COMPOUND INTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车内部用20%滑石粉填充的聚丙烯(PP)注塑成型料 与标准FOR.pdf

FORD WSS-M4D729-A4-2000 POLYPROPYLENE (PP) HOMOPOLYMER 20 % TALC FILLED INJECTION MOLDING COMPOUND EXTERIOR《汽车外部用20%滑石粉填充的聚丙烯（PP）均聚物注塑成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSS-M4D729-B1-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% MINERAL FILLED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%矿物填充聚丙烯(PP)均聚物模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf

FORD WSS-M4D729-B5-2011 POLYPROPYLENE (PP) HOMOPOLYMER 20% MINERAL FILLED MOULDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《20%矿物填充聚丙烯(PP)均聚物模塑材料 与福特WSS-M99P1111-A 一起使用》.pdf