MSZ 6786 11-1982 《木质材料的硬度规定》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

FORD WSS-M4D943-A1-2010 POLYPHTHALAMIDE + POLYPROPYLENE (PPA+PP) BLEND MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《聚邻苯二甲酰胺+聚丙烯（PP）混合物成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSS-M4D944-A1-2006 POLYPROPLENE (PP) HOMOPOLYMER 50% BARIUM SULFATE FILLED 25% MINIMUM RECYCLED CONTENT MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《再生料含量最低25%的50%硫.pdf

FORD WSS-M4D945-A1-1996 POLYPROPYLENE (PP) HOMOPOLYMER 25 % CALCIUM CARBONATE FILLED MOLDING COMPOUND《25%碳酸钙填充的聚丙烯（PP）均聚物成型料》.pdf

FORD WSS-M4D947-A1-2010 POLYAMIDE 66 (PA66) 30 % GLASS FIBER AND 15 % PTFE POWDER FILLED IMPACT MODIFIED MOLDING COMPOUND TO BE USED WITH FORD WSS-M99P1111-A 《30%玻璃纤维和15%聚四氟乙烯(PT.pdf

FORD WSS-M4D947-B1-2007 POLYAMIDE (PA) 66 25% GLASS FIBER REINFORCED IMPACT MODIFIED INTERNALLY LUBRICATED (PTFE) HEAT STABILIZED MOLDED IN COLOR MOLDING COMPOUND INTERIOR TO BE U.pdf

FORD WSS-M4D948-A1-2010 POLYCARBONATE + POLYETHYLENE TEREPHYTHALATE + POLYBUTYLENE TEREPHTHALATE BLEND (PC+PET+PBT) MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A .pdf

FORD WSS-M4D950-A1-2006 THERMOPLASTIC POLYURETHANE ELASTOMER (TPU) ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOLDING COMPOUND EXTERIOR TO BE USED WITH FORD WSS-M99P1111-A 《汽车外部用热塑性聚氨.pdf

FORD WSS-M4D951-A1-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 19% GLASS MINERAL REINFORCED TO BE USED WITH FORD WSS-M99P1111-A 《19%玻璃 矿物增强的受热稳定的聚酰胺66成型料 与标准FORD WSS-M99P1111-A一起使用 》.pdf

FORD WSS-M4D951-A2-2006 POLYAMIDE (PA) 66 HEAT STABILIZED 19% GLASS MINERAL REINFORCED 25% MIN POST CONSUMER CONTENT TO BE USED WITH FORD WSS-M99P1111-A (Shown on WSS-M4D951-A1)《.pdf