MSZ 7482 5-1981 《紫外线照射下退色检测来检验粘合剂》.pdf

相关资源

IRS 70778-2-2018 Recommendations for determining the carrying capacity and fatigue risks of existing metallic railway bridges.pdf

IRS 70712-2018 Rail defects.pdf

IRS 50596-6-2018 Conditions for coding intermodal loading units in combined transport combined transport lines and wagons.pdf

IRS 50596-5-2018 Transport of road vehicles on wagons-Technical Organisation-Conveyance of semi-trailers with P coding or N coding on recess wagons.pdf

IESNA TM-23-2017 Lighting Control Protocols.pdf

IESNA RP-2-2017 Recommended Practice for Retail Lighting.pdf

ITU-R RAPPORT M 766-2 FRENCH-1990 Feasibility of frequency sharing between the GPS and other services《全球定位系统和其他服务之间的频率共享的可行性》.pdf

ITU-R RAPPORT M 763-3 FRENCH-1990 Signal level variation due to multipath effects and blockage by ship-s superstructure in maritime mobile-satellite service lin.pdf

ITU-R RAPPORT M 739-1 FRENCH-1986 Interference due to intermodulation products in the land mobile service between 25 and 100 MHz《由于互调产物在陆地移动服务25和100 MHz之间产生的干扰》.pdf

ITU-R RAPPORT M 319-7 FRENCH-1990 Characteristics of equipment and principles governing the assignment of frequency channels between 25 and 100 MHz for land mob.pdf

猜你喜欢

GOST R IEC 60287-3-2-2011 Electric cables Calculation of the current rating Part 3-2 Sections on operating conditions Economic optimization of power cable size《电缆 额定电流的计算 第3-2部分 工作.pdf

GOST R IEC 60287-3-3-2011 Electric cables Calculation of the current rating Part 3-3 Sections on operating conditions Cables crossing external heat sources《电缆 额定电流的计算 第3-3部分 工作条件部分.pdf

GOST R IEC 60297-3-101-2006 Mechanical structures for radio-electronic equipment Subracks and associated plug-in units Dimensions of mechanical structures of the 482 6 mm (19 in) s.pdf

GOST R IEC 60297-3-102-2006 Mechanical structures for radio-electronic equipment Injector extractor handle Dimensions of mechanical structures of the 482 6 mm (19 in) series《无线与电子设.pdf

GOST R IEC 60297-3-103-2006 Mechanical structures for radio-electronic equipment Keying and alignment pin Dimensions of mechanical structures of the 482 6 mm (19 in) series《无线与电子设备.pdf

GOST R IEC 60317-0-1-2013 Specifications for particular types of winding wires Part 0-1 General requirements Enamelled round copper wire《特种绕组线规范 第0-1部分 通用要求 漆包圆铜线》.pdf

GOST R IEC 60317-0-2-2013 Specifications for particular types of winding wires Part 0-2 General requirements Enamelled rectangular copper wire《特种绕组线规范 第0-2部分 通用要求 漆包扁铜线》.pdf

GOST R IEC 60317-0-4-2013 Specifications for particular types of winding wires Part 0-4 General requirements Glass-fibre wound resin or varnish impregnated bare or enamelled rectan.pdf

GOST R IEC 60317-0-6-2013 Specifications for particular types of winding wires Part 0-6 General requirements Glass-fibre wound resin or varnish impregnated bare or enamelled round .pdf