1、A-A-59189 9018054 0000638 091 I INCH-POUND I A-A-59 189 12 May 1998 COMMERCIAL ITEM DESCRIPTION OVEN, BAKING AND ROASTING, FORCED CONVECTION, ELECTRIC (NAVAL SHIPBOARD) The General Services Administration has authorized the use of this comercial item description for all. federal agencies. 1. SCOPE T
2、his commercial item description (CID) covers single-compartment and two- compartment, baking and roasting, electric, forced convection ovens. These ovens are intended for use in Naval shipboard galleys and bakeries where combined use and time savings are required. 2. CLASSIFICATION Type 1: Single co
3、mpartment Type 2: Two compartments Size 1: Standard depth oven cavity Size 2: Extra deep oven cavity 3. SALIENT CHARACTERISTICS 3.1 Desian and construction. The front, sides, back, and top exterior surfaces of the type 1 oven shall be stainless steel; the bottom surface shall be carbon steel or stai
4、nless steel. The front, sides, and back exterior surfaces of the type 2 oven shall be stainless steel; the top and bottom surfaces shall be carbon steel or stainless steel. The type 1 oven shall provide the following features: Single oven body Removable stainless steel oven compartment linings Verti
5、cally split doors (side opening type) with handles Five equally spaced shelves capable of supporting a load of 20 pounds per square foot Removable shelves and shelf supports Beneficial comments, recommendations, additions, deletions, clarifications, etc., and any other data which may improve this do
6、cument should be sent to: Conunander, Naval Sea Systems Command, 2531 Jefferson-Davis Highway, Arlington, IVA 22242-5160. - - - I AMCC N/A FSC 7310 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted w
7、ithout license from IHS-,-,-1 I Measurements Width, overall A-A-5 9 18 9 Size 1 Minimum I Maximum 33 I 40 e Minimum 33 38 54 52 26 11 26 27 19 Two-speed oven blower to provide circulation of forced, heated air throughout the oven compartment (which becomes de-energized when the door is opened) Blowe
8、r switch (low and high speeds) Adj us tab1 e thermos tat 5-hour timer with alarm, installed in control panel or oven front Oven cavity light Indicator light (power) ON-OFF power switch Adjustable air baffle Remotely operated vent to control and release moisture from the baking chamber (operated from
9、 control panel) Maximum 40 46 69 78 38 17 30 38 22 The type 2 oven shall consist of two identical single ovens (same as type l), stacked and secured together. The oven shall preheat to 35OOF (starting from ambient air temperature of approximately 70F) in 10 minutes. Each oven compartment shall opera
10、te independently with a separate thermostat. Both type 1 and type 2 ovens shall support a uniformly distributed load of 500 pounds without any visible permanent deformation. A terminal board or box shall be provided to make permanent connections to the installation wiring system, and it shall be gro
11、unded to the oven shell. Controls, switches, and indicator lights shall be located in a control panel at the front of the oven. 3.2 Heatina units. The oven shall be provided with heating elements located to provide even heat distribution throughout the oven compartment. The heating elements shall be
12、 fully protected and removable from the oven front. The heating elements shall be energized by heat control switches. 3.3 Dimensions. Oven dimensions shall be within the limits given in Table 1. TABLE 1. Dimensions (inches). Depth, overall Height, overall (excluding vent) (1) Type 1 Type 2 to deck T
13、ype 1 Type 2 Height, from bottom of lower oven Compartment (inside) (2) Width Depth 32 54 57 26 11 26 19 39 65 78 38 17 30 25 Notes : 1. Height from finished deck 2. Each chelf/rack of size 1 ovens shall accommodate a nominal 18 x 26-inch sheet pan or roasting pan. Each shelf/rack of size 2 ovens sh
14、all accommodate two five-strap bread pans. Pans specified shall not make contact with oven interior surfaces, and contents of the load pans shall not contact oven surfaces, shelves, or racks during roasting or baking operations. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted
15、without license from IHS-,-,-A-A-59189 9038054 0000b40 7YT = A-A-5 9 18 9 3.4 Removable oven lininu Danels. Removable oven lining panels shall be stainless steel. Panels shall be made removable without the use of tools, if possible, but the use of basic tools (e.g., screwdriver, pliers, adjustable w
16、rench) is acceptable. 3.5 Oven door latch. Oven cavity door interiors shall be stainless steel. Oven doors shall be equipped with secondary exterior mechanical latches (in addition to the main interior door latches). Each side-opening-type door shall be provided wich a hold-open latch which holds th
17、e doors in a wide-open position flush with the oven interior side walls. 3.6 Mountinq. The type 1 oven shall be provided with an open stainless steel stand suitable for secure attachment to the deck. The type 2 oven shall be provided with four stainless steel legs not less than 8 inches high suitabl
18、e for secure attachment to the deck. (Shipboard requirement, see 7.2) 3.7 Inclined operation and structural intesritv. The unit shall operate satisfactorily, in accordance with the requirements of this CID (such as the door remaining closed to prevent the loss of contents), when test-operated for 30
19、 seconds inclined at an angle of 15O each side of the vertical, in each of two vertical planes at right angles to each other. The oven shall not deviate or rack from perpendicularity to the deck by more than 1/8 inch when the deck is inclined at an angle of 15O. (Shipboard requirement, see 7.2) 3.8
20、Environmental suitability. The unit shall be capable of withstanding ships vibration and motion. Controls, switches, moving parts, and electrical circuits shall operate under shipboard conditions without malfunction, binding, excessive looseness, or damage, when tested in accordance with MIL-STD-167
21、-1, type I equipment. The unit shall be secured to the test machine in the same manner that it will be secured on shipboard. (Shipboard requirement, see 7.2) 3.9 Electrical requirements. The unit shall operate on 440 VAC, 60 Hz, three- phase power, as defined in MIL-STD-1399, Section 300, and shall
22、have provisions for making direct (hardwired) connections for electric power (2 conductors) and for equipment grounding (1 conductor). All outermost metallic surfaces shall be grounded via the equipment grounding connection. The grounding resistance between any exposed metallic surfaces and the comm
23、on ground point shall be not greater than 0.1 ohm. Electrical components, other than the hermetically sealed motor, shall be provided in accordance with NEMA 250, Type 13 or equivalent enclosure protection. Metal parts of electrical components and enclosures shall be inherently corrosion resistant o
24、r shall be treated and processed for corrosion resistance in accordance with IEEE Standard 45. (Shipboard requirement, see 7.2) 3.10 Heatina elements. The ends of the heating elements shall be sealed and protected to preclude the entrance of moisture. Heating elements shall be removable from within
25、the oven cavity. Leads requiring disconnection from terminal boards or strips outside the oven shall not be used. 3.11 Accessibility. The unit shall be physically and visually accessible from the front for operation and for normal maintenance with tools, test equipment, and replacement parts. No spe
26、cial tools shall be required for access or parts replacement. 3.12 Oven cavity liuht. which is recessed and protected with a heat-resistant window. The light shall be activated by either a manual switch or an automatic door switch. The oven interir shall be provided with a light 3 Provided by IHSNot
27、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5 9 18 9 3.13 Phvsical size limitations. The unit shall pass or shall disassemble so that it can pass through a shipboard access measuring 26 x 66 inches with 8- inch radius corners. (Shipboard requirement, see 7.2)
28、3.14 Label plates. The unit shall be provided with a data nameplate and an instruction plate, both attached to the front of the unit. They shall be readily visible during normal operating use and shall not adversely affect the life and utility of the unit. 3.14.1 Data nameDlate. The data nameplate s
29、hall contain the manufacturers name, model, serial number, date manufactured, and any other information needed to uniquely identify the unit. 3.14.2 Instruction Dlate. The instruction plate shall provide instructions for start-up, operation, and shut down. 3.15 Hiqh voltaue labels. A label reading “
30、Danger-High Voltage“ shall be affixed to the outer case assembly, on or adjacent to each service access cover near one of the fasteners securing the cover. In addition, a warning label in accordance with UL 969 shall be placed near the high voltage components inside the equipment. This label shall i
31、nclude, but not be limited to the f.ollowing texts: Danger-High Voltage. Access covers must be in place before use. Power supply must be disconnected before servicing. Service should be performed by authorized personnel only. 3.16 Standards compliance. The unit shall be in accordance with and certif
32、ied to meet the applicable requirements of NSF 4 and UL 197. 4. REGULATORY REQUIREMENTS The offeror/contractor is encouraged to use recovered materials to the maximum extent practicable, in accordance with paragraph 23.403 of the Federal Acquisition Regulation. 5. QUALITY ASSURANCE PROVISIONS 5.1 Pr
33、oduct conformance. The product provided shall meet the salient characteristics of this CID, conform to the producers own drawings, specifications, standards, and quality assurance practices, and be the same product offered for sale in the commercial market, or the same product that has been delivere
34、d to the Government for shipboard use on a previous procurement. The Government reserves the right to require proof of such compliance. 6. PACKAGING Preservation, packing, and marking shall be as specified in the contract or purchase order. 7. NOTES 7.1 Orderinu data. Title, number, and date of this
35、 CID Type and size required When required, manuals shall be in accordance with ASTM F 760 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-59189 H 9018054 0000b42 512 A-A-5 9 1 8 9 7.2 Sh inboard remirement. Whenever a (Shipboard requirement) iD
36、 is included . in a paragraph under SALIENT CHARACTERISTICS, it is meant that the requirement is something that is not normally offered to the commercial market by the manufacturer. 7.3 Source of documents. 7.3.1 Militarv documents. Copies of documents required by manufacturers in connection with sp
37、ecific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer. MIL-STD-167-1 - Mechanical Vibrations of Shipboard Equipment (Type I - Environmental and Type II - Internally excited) Electric Power, Alternating MIL-STD-1399 - Interface Standar
38、d for Shipboard Systems Section 300A 7.3.2 American Societv for Testins and Materials (ASTM) Standards. AS“ standards are available from the American Society for Testing and Materials, 100 Barr Harbor Drive, West Conshohoken, PA 19428-2959. ASTM F 760 - Food Service Equipment Manuals 7.3.3 National
39、Sanitation Foundation International (NSF) Standards. NSF Standards are available from the National Sanitation Foundation International, 3475 Plymouth Road, P.O. Box 130140, Ann Arbor, MI 48113-0140. NSF 4 - Commercial Cooking, Rethermalization and Powered Hot Food Holding and Transport Equipment 7.3
40、.4 Underwriters Laboratories (UL) Standards. UL Standards are available from the Underwriters Laboratories Inc., 333 Bfingston Road, Northbrook, IL 60062. UL 197 - Comercial Electric Cooking Appliances UL 969 - Marking and Labeling Systems 7.3.5 The Institute of Electrical and Electronic Enaineers (
41、IEEE) standards. IEEE Standards are available from The Institute of Electrical and Electronic Engineers, 445 Hose Lane, P.O. Box 1331, Piscataway, NJ 08855-1331. IEEE 45 - IEEE Recommended Practice for Electric Installations on Shipboard 7.4 Suasested sources of supplv. Manufacturers of products kno
42、wn to meet the requirements of this CID are listed below. However, competition is not limited to these companies. G. S. Blodgett Company 50 Lakeside Av. Burlington, VT 05401 Lang Manufacturing Co. 6500 Merrill Creek Parkway Everett, WA 98201 Vulcan-Hart Corp. 3600 North Point Blvd. Baltimore, MD 212
43、22-2726 c Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-A-A-5q38q 9 9038054 O000643 459 A-A-5 9 10 9 MILITARY INTERESTS: Custodian: Navy - SH Army - GL CIVIL AGENCY COORDINATING ACTIVITY: GSA-FSS Preparing activity: Navy - SH (Project 7310-0891) 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
