1、NOTE: The docunent identifier and heading has been changed on this page to reflect that this is a performance specification There are no other changes to this docwnt The docunent identifier on subsequent pages has not been changed, but will be changed the next time this docunent is revised. DOD-PRF-
2、24574(SH) 29 September 1978 PERFORMANCE SPECIFICATION LUBRICATING FLUID FOR LOU AND HIGH PRESSURE OXIDIZING GAS SYSTEMS This specification is approved for use by the Naval Sea Systems Comnand and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 w. This
3、specification covers lubricating fluid for use in oxidizing gas systems, including oxygen and cocipressed air. for air and oil-free nitrogen system at pressures above 10,300 kilopascals (kPa) (1500 pounds per square inch ( 1 b/ i nZ) 1 . The Lubricating fluid is intended for use uith oxygen systems
4、at all pressures, and 1.2 Classification. Based on viscosity, volatility, and other physical properties, the lubricating fluid Type I - for use at temperatures from -46C (-50F) to 0C (32F) (see 6.1.1). Type II - for use at tanperatures from -20C (-4F) to 40C (104F) (see 6.1.2). Type 111 - for use at
5、 tenperatures from 20C (68F) to 70C (158F) (see 6.1.3). shall be of the following types, as specified (sec 6.1 and 6.2.1): 2. APPLICABLE DOCUIIENTS 2.1 Issues of docunents. The following docunents, of the issue in effect on date of invitation for bids or request for proposal, form a part of this spe
6、cification to the extent specified herein. SPEC1 F IUT IONS MILITARY MIL-M-20693 - Molding Plastic, Polyamide (Nylon), Rigid. MIL-G-23652 - Gasket and Packing Material Petroleun and Phosphate Ester Fluid Resistant. STANDARDS FEDERAL FED-STD-791 - Lubricants, liquid Fuels and Related Products, Method
7、s of Testing. MILITARY MIL-STD-105 - Sanpling Procedures and Tables for Inspection by Attributes. UIL-STD-290 - Packaging of Petroleun and Related Products. (Copies of specifications, standards, drawings, and publications required by contractors in connection uith specific procurement functions shou
8、ld be obtained from the procuring activity or as directed by the contracting officer.) The following docunmts form a part of this specification to the extent specified herein. proposal shall apply. 2.2 Other aibticcitions. Unless otherwise indicated, the issue in effect on date of invitation for bid
9、s or reqwst for Beneficial conmcnts (recconnmdetions, additions, deletioos) and any pertinent data which may be of use in inproving this docunent should be addressed to: Camnander, Naval Ship Engineering Center, SEC 6124, Department of the levy, Uashngton, DC 20362 by using the self-addressed Standa
10、rdization Docunent Inprovmt Proposal (DO Form 1426) appearing at the end of this docunent or by letter. FSC 9150 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-l)l)-I -21574 (SI ) PJlrRICA:.I SOCIIIY 101 11 il I( ,“I1 f!lllf: (7“) D 92 - Flash and r
11、irr Poiit, Clevrla-c1 0i)cri CL, D 97 - Pour Point of Ietrclcw 911s D 130 - Copper Corrosion fror- Pctrolcun Prr,c:iic$s hy tl r ColJlwr )trip ?a1,1-!, D 270 - Petroleum and Petroleum Products, Sai.iplinr: For D 287 - API Gravity of Crude Pefrolrur ancl Pctroicuri Productr (Iy X O 1 I 9 Provided by
12、IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DOD-L-24574(SH) APPENDIX Y THERMOCOUPLE ASSEMBLY REACTION VESSEL (BOMB)- 1 SUPPORT BUSHING TEST TUBE STOPPER (Y- ._I. .-, - 15 x 125 mm WIRE SUPPORT FGURE 2. g-n&e holding assembly 10 Provided by IHSNot for ResaleN
13、o reproduction or networking permitted without license from IHS-,-,-WD-L-24574 (SH) APPENDIX - 25 to 35 mm I t- -1.6 ? 0.1 mm (fit thermocouple) 12.5 0-5 mm (fit test tube) 15flmm FIGURE 3. Test tube stopper. *US GOVERNMENT PRINTING OFFICE 1978 - 603 022l5150 11 Provided by IHSNot for ResaleNo repro
14、duction or networking permitted without license from IHS-,-,-INSTRUCTIONS This form is provided to solicit beneficial comments which may improve this document and enhance its use DoD contractors, government activities, manufacturers, vendors, or other prospective users of the document are invited to
15、 submit comments to the government Fold on lines on reverse side, staple in corner. and send to preparing activity Attach any pertinent data which may be of use in improving this document If there are additionai papers, attach to form and place both in an envelope addressed to preparing actrvity A r
16、esponse will be provided to the submitter, when name and address IS provided. within 30 days indicating that the 1426 was received and when any appropnate action on it will be completed NOTE This form shall not be used to submit requests for wmvers, deviations or chfication of specirication requirem
17、ents on current contracts Comments submitted on this form do not conrtitute or imply authorization to waive any portion of the referenced document(s) or to amend contractual requirements SUBMITTED BY Printed or typed name and addnrr -Optional) I I EDITION OF 1 JAN 72 WILL BE USED UNTIL EXHAUSTED TEL
18、EPHONE NO ATE Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-FOLD DEPARTMENT OF THE NAVY NAVAL SHIP ENGINEERING CENTER WASHINGTON, D. C 20362 - OFFICIAL BUSINESS PENALTY FOR PRIVATE USE. .800 POSTAGE AND FEES PAID DEPARTMENT OF THE NAVY DOD-JI6 COMMANDER NAVAL SHIP ENGINEERING CENTER(SEC 6124) DEPARTMENT OF THE NAVY WASHINGTON, D. C. 20362 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
