1、MIL-C-LibL4F 84 m 7777906 0380554 7 m d-g+*6614F( NU) SUPERSEDING MIL-C-l7614E(NU) 3 February 1981 1987 MILITARY SPECIFICATION CAP, GARRISON, MANS This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Depart
2、ments and Agencies of the Department of Defense. l. SCOPE 1.1 Scope. This specification covers the requirements for lined and unlined garrison caps. 1.2 Classification. The .caps shall be procured in the following types, classes and sizes as specified (see 6.2): 1.2.1 Types. Type I - Lined Type II -
3、 Unlined * 1.2.2 Classes. (Type 1) Class 1 - Wool Elastique, Green 2212 Class 2 - Polyester/Wool Tropical, Khaki 3729 Class 3 - Wool Gabardine, Khaki 2115 Class 4 - Polyester/Wool Serge, Blue 3362 Class 5 - PolyesterICotton Twill, Khaki 3729 Class 6 - Polyester/Cotton Twill, Blue 3362 (Type 11) 1.2.
4、3 Sizes. 6 112, 6 518, 6 314, 6 718, 7, 7 118, 7 114, 7 318, 7 112, 7 518 7 314, 7 718, 8 Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and. Textile Research F
5、acility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this documenbor by letter. AMSC NIA FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. THIS DOCU
6、MENT CONTAINS PAPES. * Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-YIL-C-17614F 84 W 777770b 0380555 7 W 2. APPLICABLE DOCUMENTS * 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The . following specifications, standar
7、ds, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications in the solicitation. SPECIFICATIONS FEDERAL V-T-276 NN-P-7 1 DDD-L-20
8、MIL ITARY MIL-(2-368 MIL-C-823 MIL-S-3577 MIL-C-3738 MIL-C-10176 MIL-P-15011 MIL-B-1775 7 MIL-C-2 11 15 MIL-C-29 127 MIL-T-43548 MIL-S-43993 MIL-C-44121 STANDARDS FEDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-901 and Standards (DODISS) and supplement thereto, cited ri - Th
9、read, Cotton - Pallet, Material Handling, Wood, Stringer - Label; for Clothing, Equipage, and Tentage (General Construction 2 Way and 4 Way (Partial) use) - Cloth, Satin, Rayon and Cloth, Twill, Rayon - Cloth, Serge; Wool, Wool and Nylon, Polyester and - Sweatband, Headwear (Leather) - Cloth, Elasti
10、que, Wool - Cloth, Gabardine, Wool, Polyester and Wool - Pallet, Material Handling,. Wood, Post Construction, - Boxes, Shipping, Fiberboard (Modular Sizes) - Cloth, Tropical, Wool, Polyester/Wool - Cloth, Twill, Polyester/Cotton (Crease-Resistant Fi ni s h) - Thread, Polyester Core: Cotton-, Rayon-
11、or Polyester-Covered - Sweatband, Headwear, Artificial Leather - Cloth, Twill, Polyester Wool 4 Way Entry - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Storage - Palletized Unit Loads - Provisions for Evaluating Quality of Caps, Garri
12、son, Mens At t ri butes 2 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L76LqF 84 m 7977906 0380556 O m MIL-C-l7614F(NU) ( Copies of specifications, standards, drawings, and publications required by contractors. in connection with specific
13、procurement functions should be obtained from the procuring activity or as directed by the contracting ,officer) . * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent spec
14、ified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS US POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402.) * 2.2 Other p
15、ublications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issue
16、s of documents not listed in the DODISS shall be the issue of the nongovernment documents which is current on the date of the soli ci tat ion. NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to the American Tr
17、ucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinoi
18、s DEPARTMENT OF DEFENSE STANDARD COLOR CARD OF OFFICIAL STANDARDIZED SHADES FOR SEWING THREADS 60606 (Applications for copies shall be addressed to the Color Ascocaation of t,.e United States, Inc., 343 Lexington Ave., New York, N.Y. 10016). * 2.3 Order of precedence. In the event of a conflict betw
19、een the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3 Provided by IHSNot for Re
20、saleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-17bL4F 84 m 779770b 0380557 2 = 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case thi
21、s specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Basic cloths. * 3.3.1.1 Cloth, elastique, wool. The basic cloth for the Type I, Class 1 cap shall- be a wool e
22、lastique cloth conforming to Type I of MIL-C-3738. The cloth shall be dyed to match Green Shade 2212. * 3.3.1.2 Cloth, tropical, polyester/wool. The basic cloth for the Type I, Class 2 cap shall be a polyester/wool tropical conforming to Type III, Class 1 or 3 of MIL-C-21115. The cloth shall be dyed
23、 to match Khaki Shade 3729. * 3.3.1.3 Cloth, gabardine, wool. The basic cloth for the Type I, Class 3 cap shall be a wool gabardine conforming to Type I, Class 3 of MIL-C-10176. The cloth shall be dyed to match Khaki Shade 2115. * 3.3.1.4 Cloth, polyester/wool. The basic cloth for the Type I, Class
24、4 cap shall be a polyester/wool serge conforming to Type III, Class 3 of MIL-C-823. The cloth shall be dyed to match Blue Shade 3362. The standard sample piece number is 80353. * 3.3.1.5 Cloth, twill, polyester/cotton. The basic cloth for the Type II caps shall be a polyester/cotton cloth conforming
25、 to Class 1 of MIL-C-29127. The cloth shall be dyed to match Khaki Shade 3729 for the Class 5 cap and Blue Shade 3362 for the Class 6 cap. * 3.3.1.6 Cloth, twill rayon. The basic cloth for the lining pieces for the Type I caps (see 3.5.1) shall be a rayon twill cloth conforming to Class 1 of MIL-C-3
26、68. As an alternate, material conforming to MIL-C-44121 may be used. The cloth shall be dyed to approximate the shade of the basic fabric. 3.3.2 Sweatband. The sweatband for the Type I caps shall be made from either sheepskin leather conforming to MIL-S-3577 or from artificial leather conforming to
27、MIL-S-43993 dyed a brown shade to finish not less than 7/8 inch in width. When Class 4 caps are procured, the sweatband shall be black. 3.3.3 Sweatband cloth. The cloth sweatband for the Type II cap shall be made of the material specified in 3.3.1.5, cut 2 1/8 inches in width, unfinished. * 3.3.4 Th
28、read. The thread for seaming and stitching the caps shall be a cotton-covered or rayon-covered thread conforming to 2 or 3 ply, ticket No. 50 or 70 of MIL-T-43548. The polyester core, polyester covered thread is not allowed. As an alternate, the thread for seaming and stitching the caps shall be cot
29、ton thread conforming to Type I, IC2, Ticket Nos. A, and B, 3-ply of V-T-276. The thread shall be dyed to the shade specified below, in accordance with the Standard Shades for Threads, except that the thread used for 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
30、nse from IHS-,-,-MIL-C-L7bL4F BL( 7799706 0380558 4 , MIL-C-l7614F(NU) stitching the sweatband of the Type I cap shall approximate the shade of the sweatband. 0 - Type I caps Class 1 - Olive Drab T-1, Cable No. 66023 Classes 2 and 3 - Khaki P-1, Cable No. 66019 Class 4 - Navy Blue AT, Cable No. 6606
31、0 . Type II caps Class 5 - Khaki P-1, Cable No. 66019 Class 6 - Navy Blue AT, Cable No. 66060 * 3.3.4.1 Colorfastness. The dyed thread shall show fastness to light, laundering, wet-dry cleaning, and perspiration equal to or better than the standard sample when tested as specified in V-T-276 or MIL-T
32、-43548. When a standard sample is not available, the dyed thread shall show a minimum of “good“ fastness to light, laundering, wet-dry cleaning, and perspiration, when tested as specified in V-T-276 or MIL-T-43548. * 3.3.5 Labels. Each cap shall have a combination identification, size, and personal
33、label and a separate instruction label in accordance with 3.3.5.1 and 3.3.5.2. * 3.3.5.1 Combination label. Each cap shall have an identification, size, and personal label conforming to Type VI, classes 4 and 10, of ODD-L-20, except that the inscription shall be as shown below. The size of the label
34、 shall be not more than 1-1/2 inches in height and 2-1/2 inches in length. The height of the lettering except for the applicable size shall be 1/16 to 1/8 inch. The size lettering shall be not less than 1/4 inch. The label shall show fastness to drycleaning only when Type I caps are applicable and t
35、o laundering only when Type II caps are applicable. O NAME : SERVICE NO.: CAP, GARRISON, MANS (100% WOOL) (EXAMPLE) CONTRACT NO.: DLA-100-00-0-000 (EXAMPLE) STOCK NO.: 8405-00-000-0000 (EXAMPLE) NAME OF CONTRACTOR: SIZE : * 3.3.5.2 Instruction label. Each cap shall have an instruction label conformi
36、ng to Type VI, Class 3 of DDD-L-20. The size of the label shall be not more than 1-1/2 inches in height and 2-1/2 inches in length. The size of the lettering shall be 1/16 to 1/8 inch. The label shall show fastness to drycleaning only when Type I caps are applicable and to laundering only when Type
37、II caps are applicable. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-LAUNDERING INSTRUCTIONS DRY CLEAN ONLY MACHINE WASH WARM, PERMANENT PRESS CYCLE TUMBLE DRY, MEDIUM SETTING REMOVE PROMPTLY DO NOT USE CHLORINE BLEACH OR Follow NAVEDTRA Manual
38、414-01-45-81 Formula IL 3,4 Design. The cap shall be of a garrison style, having a three piece crown and a one pfece curtain turned up on the outside of the cap with the tapered Bends crossing at the front. The caps shall be lined or unlined and shall have a leather, artificial leather or basic clot
39、h sweatband, as specified. 3.4.1 Figures. Figures 1 and 2 are furnished for information purpases only. When inconsistencies exist between the written specification and the figures, the written specification shall govern. * 3.5 Patterns. Standard patterns to be used to cut the working patterns will b
40、e furnished by the Government (see 6.3). The working patterns shall be identical to the Government patterns. Neither-the Government patterns nor the working patterns shall be altered in any way. * 3.5.1 List of pattern parts. The caps shall be cut from material as specified, and in accordance with p
41、attern parts inicated below: Mat er i al Nomenclature Cut parts Appldcabl e basic material Side crown 2 Top crown (gusset) 1 Curtain 1 Rayon twill cloth Side crown lining (Type i only) 2 3.6 Construction. * 3.6.1 Stitches, seams, and stitchings. Stitch, seams, and stitching types, as specified in Ta
42、ble I shall conform to the requirements of FED-STD-751. Whenever two or more methods for seams or stitchings are given for the same operation, any one of them may be used. Seam allowances shall be maintained with seams sewn so that no raw edges, runoffs, twists, pleats, puckers, or open seams result
43、. All seams shall start and finish evenly. Thread tension shall be maintained so that there is no tight or loose stitching. Where stitch type 401 is used, the looper (underthread) shall be on the inside of- the cap. Ends of all seams prodvced by stitch type 401 shall be caught in Provided by IHSNot
44、for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-L7614F 84 9779706 0380560 2 W MIL-C-l7614F( NU) other seams or stitchings. The width of the safety stitch shall be 3/8 inch and the guides and knives on the safety stitch machine shall be set to trim only the ravell
45、ed ends of the fabric. 3.6.2 Stitches per inch. The minimum and maximum number of stitches per inch shall be as specified in Table I. * 3.6.3 Thread breaks and ends of seams. Ends of type 301 seams and stitchings, when not caught in other seams or stitchings, shall be backtacked not less than 1/4 in
46、ch. The ends of a continuous line of stitching shall be overlapped not less than 1/2 inch. Thread breaks (all stitch types) shall be secured by stitching back of break not less than 1/2 inch. Skipped stitches or thread breaks may be repaired by using 301 stitch type. The ends of type 401 stitching n
47、ot caught in other stitching or seams shall have a 1/2 to 3/4 inch chain extending from it. 3.7 Mankfacturing operations requirements. The caps shall be manufactured in accordance with the operation requirements specified in Table I. The contractor is not required to follow the exact sequence of ope
48、rations listed, provided that the finished cap is identical to that produced by following the sequence of operations as listed in Table I. 3.7.1 Shade and size marking. The component parts shall be marked or ticketed to insure a uniform shade and size throughout the cap. Any method may be used excep
49、t: 1. Metal fastening devices 2. Sewn-on tickets 3. Adhesive type tickets whose adhesive causes discoloration or whose adhesive mass adheres to the material upon removal of the tickets. The use of a rubber stamp, ink pad numbering machine, or pencil is acceptable provided the numbers are legible and are not visible on the outside of the cap. 3.7.2 Pressing. All pressing as required in Table I shall be performed with a steam iron or steam pressing machine.
